scholarly journals Influence of Welding Speed on the Microstructure and Mechanical Properties of Electron Beam-Welded Joints of TC4 and 4J29 Sheets using Cu/Nb Multi-Interlayers

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 810 ◽  
Author(s):  
Defeng Mo ◽  
Yang Wang ◽  
Yongjian Fang ◽  
Tingfeng Song ◽  
Xiaosong Jiang
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Electron Beam ◽  
Welding Speed ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Microstructure And Mechanical Properties ◽  
Hardness Tests ◽  
Weld Appearance

Dissimilar metal joining between titanium and kovar alloys was conducted using electron beam welding. Metallurgical bonding of titanium alloys and kovar alloys was achieved by using a Cu/Nb multi-interlayer. The effects of welding speed on weld appearance, microstructure and mechanical properties of welded joints were investigated. The microstructure of welded joints was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS). The mechanical properties of welded joints were investigated by tensile strength and micro-hardness tests. The results showed that welding speed had great effects on the weld appearance, microstructure, and mechanical properties of electron beam-welded joints. With an increase of welding speed, at the titanium alloy side, the amount of (Nb,Ti) solid solution was increased, while the formation of brittle FeTi was effectively suppressed. At the kovar alloy side, microstructure was mainly composed of soft Cu solid solution and some α-Fe + γ phases. In addition, higher welding speeds within a certain range was beneficial for eliminating the formation of cracks, and inhibiting the embrittlement of welded joints. Therefore, the tensile strength of welded joints was increased to about 120 MPa for a welding speed of 10 mm/s. Furthermore, the bonding mechanism of TC4/Nb/Cu/4J29 dissimilar welded joints had been investigated and detailed.

Investigation on the microstructure and mechanical properties of Ti6Al4V titanium alloy electron beam welding joint

2022 ◽  
pp. 095440622110329
Author(s):  
Xilong Zhao ◽  
Xinhong Lu ◽  
Kun Wang ◽  
Feng He
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Electron Beam ◽  
Penetration Depth ◽  
Welding Speed ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Martensite Phase ◽  
Ti6al4v Titanium Alloy ◽  
Microstructure And Mechanical Properties

Electron beam welding (EBW) is a fusion joining process particularly suitable for welding titanium plates. In the present work, 2.5 mm thickness Ti6Al4V titanium alloy plates were butt-welded together with backing plates by EBW. The detailed procedures of experiments were used to investigate the microstructure and mechanical properties of welded joints. The optimum welding speed was determined by microstructure examinations, microhardness tests, X-Ray diffraction tests, shear punch tests (SPT) and stress simulation calculations. The results showed that all microstructure of welded metal (WM) was martensite phase under the different welding speeds. In the heat-affected zone (HAZ), the martensite phase gradually evolved to be small and equiaxed. It can be seen that the microstructure of each region in welded joints did not change significantly. When the welding speed is between 8 mm/s and 14 mm/s, it can be seen from the macroscopic appearance of the joints that there was no utterly fused penetration between the butt plate and substrate. Finite element simulation was carried out for the no-penetration depth under different welding conditions, and it was found that the stress suffered by the small no-penetration depth was the smallest. Using different welding parameters shows that the engineering stress in WM was higher than other areas, and BM was the lowest. As welding speed increases from 8 mm/s to 14 mm/s, the variation of microhardness distribution was not evident.

scholarly journals Microstructure and Mechanical Properties of Electron Beam-Welded Joints of Titanium TC4 (Ti-6Al-4V) and Kovar (Fe-29Ni-17Co) Alloys with Cu/Nb Multi-Interlayer

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Yong-jian Fang ◽  
Xiao-song Jiang ◽  
De-feng Mo ◽  
Ting-feng Song ◽  
Zhen-yi Shao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Titanium Alloy ◽  
Electron Beam ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
X Ray Diffraction ◽  
Strength Tests

Electron beam welding of a titanium alloy (Ti-6Al-4V) and a kovar alloy (Fe-29Ni-17Co) was performed by using a Cu/Nb multi-interlayer between them. Microstructure and composition of welded joints were analyzed by means of optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction. Mechanical properties of welded joints were evaluated by microhardness and tensile strength tests. Results indicated that in case of 0.22 mm thickness of Nb foil, microstructure of the titanium alloy side was mainly composed of Ti solid solution and some intermetallic compounds such as FeTi and CuTi2, whereas in case of 0.40 mm thickness of Nb foil, the appearance of weld was more uniform and hardness of the weld zone decreased sharply. However, tensile strength of welded joints was increased from 88.1 MPa for the 0.22 mm Nb foil to 150 MPa for the 0.40 mm Nb foil. It was found that thicker Nb foil could inhibit diffusion of Fe atoms towards the titanium alloy side, thus promoting the formation of Ti solid solution and a small amount of CuTi2 and eliminating FeTi. In addition, in both cases, Cu0.5Fe0.5Ti was found in the fusion zone of the titanium alloy side, which had an adverse effect on mechanical properties of welded joints.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

scholarly journals Application of Dynamic Beam Positioning for Creating Specified Structures and Properties of Welded Joints in Electron-Beam Welding

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2233
Author(s):  
Tatyana Olshanskaya ◽  
Vladimir Belenkiy ◽  
Elena Fedoseeva ◽  
Elena Koleva ◽  
Dmitriy Trushnikov
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Weld Metal ◽  
Thermal Effect ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Welded Joint ◽  
Parent Metal ◽  
Cooling Rates ◽  
Structures And Properties

The application of electron beam sweep makes it possible to carry out multifocal and multi-beam welding, as well as combine the welding process with local heating or subsequent heat treatment, which is important when preparing products from thermally-hardened materials. This paper presents a method of electron beam welding (EBW) with dynamic beam positioning and its experimental-calculation results regarding the formation of structures and properties of heat-resistant steel welded joints (grade of steel 20Cr3MoWV). The application of electron beam oscillations in welding makes it possible to change the shape and dimensions of welding pool. It also affects the crystallization and formation of a primary structure. It has been established that EBW with dynamic beam positioning increases the weld metal residence time and the thermal effect zone above the critical A3 point, increases cooling time and considerably reduces instantaneous cooling rates as compared to welding without beam sweep. Also, the difference between cooling rates in the depth of a welded joint considerably reduces the degree of structural non-uniformity. A bainitic–martensitic structure is formed in the weld metal and the thermal effect zone throughout the whole depth of fusion. As a result of this structure, the level of mechanical properties of a welded joint produced from EBW with dynamic electron beam positioning approaches that of parent metal to a greater extent than in the case of welding by a static beam. As a consequence, welding of heat-resistant steels reduces the degree of non-uniformity of mechanical properties in the depth of welded joints, as well as decreases the level of hardening of a welded joint in relation to parent metal.

Influence of Sr Addition on Microstructure and Mechanical Properties of Ignition-Proof AZ91D-0.3Be Magnesium Alloy

2011 ◽  
Vol 335-336 ◽  
pp. 783-786
Author(s):  
Fu Yin Han ◽  
Lin Hai Tian ◽  
Hong Xia Wang ◽  
Wei Liang ◽  
Wen Xian Wang
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Cast Alloy ◽  
Solid Solution Alloy ◽  
Aged Alloy ◽  
Microstructure And Mechanical Properties ◽  
Solid Liquid Interface ◽  
Solid Liquid

Sr added ignition-proof AZ91D-0.3Be magnesium alloy was prepared. The influence of Sr content on microstructure and mechanical properties of the alloy was studied. Results show that the microstructure of ignition-proof AZ91D-0.3Be magnesium alloy is refined by a small amount of Sr addition. It is due to that the enrichment of a few Sr atoms in solid liquid interface in the process of magnesium alloy solidification inhibits grain growth and accelerates more nucleation. However, with increasing of Sr addition the microstructure is coarsened. By 0.01% Sr addition the tensile strength of as-cast experimental alloy is increased by about 25% and that of both the solid-solution and aged alloy is increased by about 40%. The elongation of as-cast alloy is increased by about 20% and that of solid-solution alloy increased by about 30%.

Sign in / Sign up

Export Citation Format

Share Document