scholarly journals Microstructure and Mechanical Properties of Electron Beam-Welded Joints of Titanium TC4 (Ti-6Al-4V) and Kovar (Fe-29Ni-17Co) Alloys with Cu/Nb Multi-Interlayer

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Yong-jian Fang ◽  
Xiao-song Jiang ◽  
De-feng Mo ◽  
Ting-feng Song ◽  
Zhen-yi Shao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Titanium Alloy ◽  
Electron Beam ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Weld Zone ◽  
X Ray Diffraction ◽  
Strength Tests

Electron beam welding of a titanium alloy (Ti-6Al-4V) and a kovar alloy (Fe-29Ni-17Co) was performed by using a Cu/Nb multi-interlayer between them. Microstructure and composition of welded joints were analyzed by means of optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction. Mechanical properties of welded joints were evaluated by microhardness and tensile strength tests. Results indicated that in case of 0.22 mm thickness of Nb foil, microstructure of the titanium alloy side was mainly composed of Ti solid solution and some intermetallic compounds such as FeTi and CuTi2, whereas in case of 0.40 mm thickness of Nb foil, the appearance of weld was more uniform and hardness of the weld zone decreased sharply. However, tensile strength of welded joints was increased from 88.1 MPa for the 0.22 mm Nb foil to 150 MPa for the 0.40 mm Nb foil. It was found that thicker Nb foil could inhibit diffusion of Fe atoms towards the titanium alloy side, thus promoting the formation of Ti solid solution and a small amount of CuTi2 and eliminating FeTi. In addition, in both cases, Cu0.5Fe0.5Ti was found in the fusion zone of the titanium alloy side, which had an adverse effect on mechanical properties of welded joints.

scholarly journals Influence of Welding Speed on the Microstructure and Mechanical Properties of Electron Beam-Welded Joints of TC4 and 4J29 Sheets using Cu/Nb Multi-Interlayers

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 810 ◽  
Author(s):  
Defeng Mo ◽  
Yang Wang ◽  
Yongjian Fang ◽  
Tingfeng Song ◽  
Xiaosong Jiang
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Electron Beam ◽  
Welding Speed ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Microstructure And Mechanical Properties ◽  
Hardness Tests ◽  
Weld Appearance

Dissimilar metal joining between titanium and kovar alloys was conducted using electron beam welding. Metallurgical bonding of titanium alloys and kovar alloys was achieved by using a Cu/Nb multi-interlayer. The effects of welding speed on weld appearance, microstructure and mechanical properties of welded joints were investigated. The microstructure of welded joints was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS). The mechanical properties of welded joints were investigated by tensile strength and micro-hardness tests. The results showed that welding speed had great effects on the weld appearance, microstructure, and mechanical properties of electron beam-welded joints. With an increase of welding speed, at the titanium alloy side, the amount of (Nb,Ti) solid solution was increased, while the formation of brittle FeTi was effectively suppressed. At the kovar alloy side, microstructure was mainly composed of soft Cu solid solution and some α-Fe + γ phases. In addition, higher welding speeds within a certain range was beneficial for eliminating the formation of cracks, and inhibiting the embrittlement of welded joints. Therefore, the tensile strength of welded joints was increased to about 120 MPa for a welding speed of 10 mm/s. Furthermore, the bonding mechanism of TC4/Nb/Cu/4J29 dissimilar welded joints had been investigated and detailed.

Investigation on the microstructure and mechanical properties of Ti6Al4V titanium alloy electron beam welding joint

2022 ◽  
pp. 095440622110329
Author(s):  
Xilong Zhao ◽  
Xinhong Lu ◽  
Kun Wang ◽  
Feng He
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloy ◽  
Electron Beam ◽  
Penetration Depth ◽  
Welding Speed ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Martensite Phase ◽  
Ti6al4v Titanium Alloy ◽  
Microstructure And Mechanical Properties

Electron beam welding (EBW) is a fusion joining process particularly suitable for welding titanium plates. In the present work, 2.5 mm thickness Ti6Al4V titanium alloy plates were butt-welded together with backing plates by EBW. The detailed procedures of experiments were used to investigate the microstructure and mechanical properties of welded joints. The optimum welding speed was determined by microstructure examinations, microhardness tests, X-Ray diffraction tests, shear punch tests (SPT) and stress simulation calculations. The results showed that all microstructure of welded metal (WM) was martensite phase under the different welding speeds. In the heat-affected zone (HAZ), the martensite phase gradually evolved to be small and equiaxed. It can be seen that the microstructure of each region in welded joints did not change significantly. When the welding speed is between 8 mm/s and 14 mm/s, it can be seen from the macroscopic appearance of the joints that there was no utterly fused penetration between the butt plate and substrate. Finite element simulation was carried out for the no-penetration depth under different welding conditions, and it was found that the stress suffered by the small no-penetration depth was the smallest. Using different welding parameters shows that the engineering stress in WM was higher than other areas, and BM was the lowest. As welding speed increases from 8 mm/s to 14 mm/s, the variation of microhardness distribution was not evident.

Microstructure and mechanical properties of 9Cr-3W-3Co steel welded joints by vacuum electron beam welding

2021 ◽  
pp. 2150192
Author(s):  
Youyi Zhang ◽  
Guoqing Gou
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
High Temperature ◽  
Base Metal ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Lath Martensite ◽  
Weld Zone ◽  
Creep Fracture ◽  
Welding Joints

This paper aims to explore the microstructure and mechanical properties of 9Cr-3W-3Co steel welded joints. In the experiment, 9Cr-3W-3Co steel samples were welded by vacuum electron beam welding technology (VEBW) without any metal stuff, and all the welding joints were treated by high-temperature tempering at [Formula: see text]C for 8 h. The microstructure of welding joints was observed by OM, SEM and TEM; and the mechanical properties of welded joints were analyzed by microhardness test, room-temperature tensile, test impact test and high-temperature creep test. As a result, all the 9Cr-3W-3Co steel samples displayed the microstructure status as martensite under the Scheffler-Schneider prediction model, which conformed to the expectation. After high-temperature tempering, the grains of the welding zone were smaller than the base metal and the composition was tempered lath martensite only. Some of the lath martensite bundles even showed the incomplete polygonal transformation. The M[Formula: see text]C6 carbides and MX phase were distributed continuously along with the lath martensite interfaces, which showed a tendency for further aggregation. The microhardness of the weld zone was slightly higher than the base metal (mean of base metal: 240 HV[Formula: see text], mean of weld zone: 273 HV[Formula: see text] and mean of heat affected area: 274 HV[Formula: see text]. There was no softening phenomenon observed, and the welding joints maintaining the high intensity. Other mechanical properties like the tensile strength (mean: 750 MPa), yield strength (mean: 707 MPa) and impact toughness (mean of WM: 25.1 J and HAZ: 23.3 J) were also excellent. When the temperature parameter is constant, the time for creep fracture reduces significantly with the increase of the stress; whereas the time for creep fracture decreases significantly as the temperature increases, while the stress parameter is constant.

scholarly journals Application of Dynamic Beam Positioning for Creating Specified Structures and Properties of Welded Joints in Electron-Beam Welding

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2233
Author(s):  
Tatyana Olshanskaya ◽  
Vladimir Belenkiy ◽  
Elena Fedoseeva ◽  
Elena Koleva ◽  
Dmitriy Trushnikov
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Weld Metal ◽  
Thermal Effect ◽  
Welded Joints ◽  
Electron Beam Welding ◽  
Welded Joint ◽  
Parent Metal ◽  
Cooling Rates ◽  
Structures And Properties

The application of electron beam sweep makes it possible to carry out multifocal and multi-beam welding, as well as combine the welding process with local heating or subsequent heat treatment, which is important when preparing products from thermally-hardened materials. This paper presents a method of electron beam welding (EBW) with dynamic beam positioning and its experimental-calculation results regarding the formation of structures and properties of heat-resistant steel welded joints (grade of steel 20Cr3MoWV). The application of electron beam oscillations in welding makes it possible to change the shape and dimensions of welding pool. It also affects the crystallization and formation of a primary structure. It has been established that EBW with dynamic beam positioning increases the weld metal residence time and the thermal effect zone above the critical A3 point, increases cooling time and considerably reduces instantaneous cooling rates as compared to welding without beam sweep. Also, the difference between cooling rates in the depth of a welded joint considerably reduces the degree of structural non-uniformity. A bainitic–martensitic structure is formed in the weld metal and the thermal effect zone throughout the whole depth of fusion. As a result of this structure, the level of mechanical properties of a welded joint produced from EBW with dynamic electron beam positioning approaches that of parent metal to a greater extent than in the case of welding by a static beam. As a consequence, welding of heat-resistant steels reduces the degree of non-uniformity of mechanical properties in the depth of welded joints, as well as decreases the level of hardening of a welded joint in relation to parent metal.

Tensile Strength of Forged Ti-6Al-4V Welded Joints by Electronic Beam Welding

2011 ◽  
Vol 255-260 ◽  
pp. 132-136
Author(s):  
Hong Yu Qi ◽  
Jian Xie ◽  
Dong Pan ◽  
Shao Lin Li ◽  
Xiao Guang Yang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Base Metal ◽  
Welded Joints ◽  
Empirical Relationship ◽  
Weld Zone ◽  
Structure Design ◽  
Microstructure And Mechanical Properties ◽  
Welded Structure ◽  
Static Tensile

Forged Ti-6Al-4V welded structure by electronic beam welding (EBW) as integrally bladed disk (blisk) structure in advanced aero-engine has been widely applied. It is necessary to analyze microstructure and mechanical properties of Ti-6Al-4V welded joints by EBW for failure analysis and structure design of blisk. Firstly the microstructure and mechanical properties of forged Ti-6Al-4V welded joints was focused on. Grains in the weld zone become coarse and large gradient organization structure appears in the heat affected zone (HAZ), which presents significant local heterogeneity. Microhardness of the weld zone is about 20% higher than that of the base metal. The size of different region of the welded joints was estimated. Then static tensile test of three different specimens were carried on. Experiment results show that the tensile and yield strength of welded joints are not less than that of the base metal. Finally the empirical relationship between strength and hardness of Ti-6Al-4V alloy is established. Tensile strength of the weld zone and the base metal were estimated. Compared to experiment data, the deviation is 3.56%, 0.097% respectively.

Sign in / Sign up

Export Citation Format

Share Document