scholarly journals Insights into Machining of a β Titanium Biomedical Alloy from Chip Microstructures

Metals ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 710 ◽  
Author(s):  
Damon Kent ◽  
Rizwan Rahman Rashid ◽  
Michael Bermingham ◽  
Hooyar Attar ◽  
Shoujin Sun ◽  
...  
Keyword(s):  
Shear Band ◽  
Shear Zone ◽  
Biomechanical Properties ◽  
Temperature Fields ◽  
Large Strains ◽  
Shear Direction ◽  
Grain Sizes ◽  
Β Phase ◽  
Secondary Shear Zone ◽  
Cutting Speeds

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study, machining chip microstructure has been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

scholarly journals Insights Into Machining of a β Titanium Biomedical Alloy from Chip Microstructures

2018 ◽  
Author(s):  
Damon Kent ◽  
Rizwan Rahman Rashid ◽  
Michael Bermingham ◽  
Hooyar Attar ◽  
Shoujin Sun ◽  
...  
Keyword(s):  
Shear Band ◽  
Shear Zone ◽  
Beta Phase ◽  
Biomechanical Properties ◽  
Alpha Phase ◽  
Temperature Fields ◽  
Large Strains ◽  
Shear Direction ◽  
Beta Titanium ◽  
Secondary Shear Zone

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400-600°C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20-50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720°C β transus temperature.

scholarly journals Insights into Machining of a β Titanium Biomedical Alloy from Chip Microstructures

2018 ◽  
Author(s):  
Damon Kent ◽  
Rizwan Rahman Rashid ◽  
Michael Bermingham ◽  
Hooyar Attar ◽  
Shoujin Sun ◽  
...  
Keyword(s):  
Shear Band ◽  
Shear Zone ◽  
Beta Phase ◽  
Biomechanical Properties ◽  
Alpha Phase ◽  
Temperature Fields ◽  
Large Strains ◽  
Shear Direction ◽  
Beta Titanium ◽  
Secondary Shear Zone

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

scholarly journals Intergranular Corrosion and Microstructural Evolution in a Newly Designed Al-6Mg Alloy

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3314
Author(s):  
Kweon-Hoon Choi ◽  
Bong-Hwan Kim ◽  
Da-Bin Lee ◽  
Seung-Yoon Yang ◽  
Nam-Seok Kim ◽  
...  
Keyword(s):  
Intergranular Corrosion ◽  
Alloy System ◽  
Critical Factors ◽  
Phase Precipitation ◽  
Grain Sizes ◽  
Β Phase ◽  
Mass Losses ◽  
Cold Rolling Reduction ◽  
Cold Rolled ◽  
Sensitization Time

In this work, the microstructure and corrosion behavior of a novel Al-6Mg alloy were investigated. The alloy was prepared by casting from pure Al and Mg+Al2Ca master alloy. The ingots were homogenized at 420 °C for 8 h, hot-extruded and cold-rolled with 20% reduction (CR20 alloy) and 50% reduction (CR50 alloy). The CR50 alloy exhibited a higher value of intergranular misorientation due to a higher cold rolling reduction ratio. The average grain sizes were 19 ± 7 μm and 17 ± 9 μm for the CR20 and CR50 alloys, respectively. An intergranular corrosion (IGC) behavior was investigated after sensitization by a nitric acid mass-loss test (ASTM G67). The mass losses of both the CR20 and CR50 alloys were similar at early periods of sensitization, however, the CR20 alloy became more susceptible to IGC as the sensitization time increased. Grain size and β phase precipitation were two critical factors influencing the IGC behavior of this alloy system.

Transient Elastic Thermal Stress Development During Laser Scribing of Ceramics

2000 ◽  
Vol 123 (1) ◽  
pp. 171-177 ◽  
Author(s):  
Michael F. Modest ◽  
Thomas M. Mallison
Keyword(s):  
Thermal Stresses ◽  
Continuous Wave ◽  
Elastic Stress ◽  
Three Dimensional ◽  
Thick Layer ◽  
Temperature Fields ◽  
Subsurface Cracks ◽  
Laser Scribing ◽  
Micro Cracks ◽  
Cutting Speeds

Lsaers are emerging as a valuable tool for shaping and cutting hard and brittle ceramics. Unfortunately, the large, concentrated heat flux rates that allow the laser to efficiently cut and shape the ceramic also result in large localized thermal stresses in a small heat-affected zone. These notable thermal stresses can lead to micro-cracks, a decrease in strength and fatigue life, and possibly catastrophic failure. In order to assess where, when, and what stresses occur during laser scribing, an elastic stress model has been incorporated into a three-dimensional scribing and cutting code. First, the code predicts the temporal temperature fields and the receding surface of the ceramic. Then, using the scribed geometry and temperature field, the elastic stress fields are calculated as they develop and decay during the laser scribing process. The analysis allows the prediction of stresses during continuous wave and pulsed laser operation, a variety of cutting speeds and directions, and various shapes and types of ceramic material. The results of the analysis show substantial tensile stresses develop over a thick layer below and parallel to the surface, which may be the cause of experimentally observed subsurface cracks.

Effect of Minimum Quantity Lubrication to Prediction of Cutting Temperature Distribution in Turning Material AISI-1045

2020 ◽  
Vol 902 ◽  
pp. 97-102
Author(s):  
Tran Trong Quyet ◽  
Pham Tuan Nghia ◽  
Nguyen Thanh Toan ◽  
Tran Duc Trong ◽  
Luong Hong Sam ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Shear Zone ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Chip Thickness ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
The Difference ◽  
Secondary Shear Zone ◽  
Cutting Model

This paper presents a prediction of cutting temperature in turning process, using a continuous cutting model of Johnson-Cook (J-C). An method to predict the temperature distribution in orthogonal cutting is based on the constituent model of various material and the mechanics of their cutting process. In this method, the average temperature at the primary shear zone (PSZ) and the secondary shear zone (SSZ) were determined for various materials, based on a constitutive model and a chip-formation model using measurements of cutting force and chip thicknes. The J-C model constants were taken from Hopkinson pressure bar tests. Cutting conditions, cutting forces and chip thickness were used to predict shear stress. Experimental cutting heat results with the same cutting parameters using the minimum lubrication method (MQL) were recorded through the Testo-871 thermal camera. The thermal distribution results between the two methods has a difference in value, as well as distribution. From the difference, we have analyzed some of the causes, finding the effect of the minimum quantity lubrication parameters on the difference.

scholarly journals The examination of the effect of variable cutting speeds on the surface and edge qualities of milled granite materials

2019 ◽  
Vol 11 (7) ◽  
pp. 168781401983631 ◽  
Author(s):  
István Gábor Gyurika ◽  
Tibor Szalay
Keyword(s):  
Surface Roughness ◽  
Cutting Speed ◽  
Sample Surface ◽  
Average Surface Roughness ◽  
Edge Chipping ◽  
Average Surface ◽  
Grain Sizes ◽  
Natural Stones ◽  
Cutting Speeds

Automated stone manufacturing has undergone considerable development in recent years. Thanks to international research dealing with the cutting, sawing and grinding of different natural stones, processing time shortens and tool-life lengthens. However, the process of stone milling has not been extensively examined yet, primarily because of the novelty of this technology. The aim of the research described in this article is to examine how variable cutting speed affects the quality of workpiece edges while milling granite materials. For the research, sample surfaces were formed on five granite slabs with different average grain sizes using five cutting speed values. Afterwards, changes in the average surface roughness and average edge chipping rate were examined. From the research results, it can be concluded that, due to an increase in cutting speed, the average edge chipping rate will decrease until reaching a borderline speed. In the case of a higher cutting speed, the referent tendency cannot be ascertained. A statistical analysis conducted in the scope of this research showed that if a variable cutting speed is applied, then changes in the quality of the sample surface edge can be inferred from the development trends of average surface roughness.

Investigation of Bulging Behavior of Coke Drum—A Practical Analysis of Bulging Under Complex Quench Conditions

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Toshiya Yamamoto ◽  
Kazuaki Arii ◽  
Shinta Niimoto ◽  
Mitsuru Ohata ◽  
Tetsuya Tagawa ◽  
...  
Keyword(s):  
Temperature Profile ◽  
Cooling Water ◽  
Fe Analysis ◽  
Temperature Fields ◽  
Large Strains ◽  
Analysis Model ◽  
Actual Operation ◽  
Feasible Study ◽  
Temperature Strain ◽  
Rapid Drop

Coke drums undergo cyclic operations typically in the temperature range from room temperature to about 500 °C (930 °F). During quenching, the coke drum is inevitably subjected to a rapid drop in temperature because cooling water is injected directly into the coke drum through the bottom inlet nozzle. The temperature profile on the shell surface is uneven during quenching, and can vary in each cycle of the quenching operation. Such a complicated thermal profile induces large strains in the shell portion of the coke drum, and eventually causes damage like bulging and/or cracking. The authors have investigated the bulging behavior of the coke drum by the thermal elastic-plastic finite element (FE)-analysis, considering the existence of the overmatch welds and uneven temperature field during quenching (Ohata et al., 2011, “Investigation of Bulging Behavior of Coke Drum—Feasible Study on Causes of Bulging,” ASME PVP2011-57276, Baltimore). In this paper, a practical FE-analysis is developed to estimate the complex strain that leads to bulging under uneven temperature fields during quenching. The actual temperature and strain data during operation are collected by thermocouples and high temperature strain gauges. A thermal analysis model, including an evaluation of boiling heat transfer on the shell's inner surface, is established to simulate the measured shell behavior of the coke drum. By utilizing this FE-analysis model, several parameters thought of as causal factors in bulging can be examined under the uneven temperature profile that is likely to occur during actual operation. This analytical approach can also provide effective technique for improvements in shell durability.

On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel

1982 ◽  
Vol 104 (2) ◽  
pp. 121-131 ◽  
Author(s):  
R. Komanduri ◽  
T. Schroeder ◽  
J. Hazra ◽  
B. F. von Turkovich ◽  
D. G. Flom
Keyword(s):  
Titanium Alloys ◽  
Shear Zone ◽  
Chip Formation ◽  
High Speed ◽  
Shear Bands ◽  
Shear Instability ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Cutting Speeds ◽  
Aisi 4340

An AISI 4340 Steel (325 BHN) was machined at various speeds up to 2500 m/min (8000 SFPM). Longitudinal midsections of the chips were examined metallurgically to delineate the differences in the chip formation characteristics at various speeds. Chips were found to be continuous at 30 to 60 m/min (100 to 200 SFPM) but discontinuous below this speed. Instabilities in the cutting process, leading to different types of cyclic chip formations, were observed at cutting speeds above 60 m/min (200 SFPM). Fully developed catastrophic shear bands separated by large areas (segments) of relatively less deformed material, similar to that when machining titanium alloys, were observed in the chips at cutting speeds above 275 m/min (800 SFPM). The intense shear bands between the segments appeared to have formed subsequent to the localized intense deformation of the segment in the primary shear zone. As the cutting speed increases, the extent of contact between the segments is found to decrease rapidly. At speeds of 1000 m/min (3200 SFPM) and above, due to rapid intense, localized shear between the segments, these segments were found to separate completely as isolated segments instead of being held intact as a long chip. The speed at which this decohesion occurs was found to depend upon the metallurgical state of the steel machined and its hardness. As in the case of machining titanium alloys, the deformation of the chip as it slides on the tool face, i.e., “secondary shear zone,” appeared to be negligible when machining this AISI 4340 steel at high speed. Based on the metallurgical study of the chip and the similarities of machining this material at high speed and that of titanium alloys at normal speed, a cyclic phenomenon in the primary shear zone is identified as the source of instability responsible for the large-scale heterogeneity and a mechanism of chip formation when machining AISI 4340 steel at high speed is proposed.

Primary Chip Formation During an Extremely High Speed Micromachining Process

2004 ◽  
Author(s):  
M. J. Jackson ◽  
C. H. Hamme ◽  
L. J. Hyde ◽  
G. M. Robinson ◽  
H. Sein ◽  
...  
Keyword(s):  
Shear Zone ◽  
Chip Formation ◽  
High Speed ◽  
Cutting Tools ◽  
Machining Processes ◽  
Orthogonal Machining ◽  
Shear Process ◽  
Order Of Magnitude ◽  
Cutting Zone ◽  
Secondary Shear Zone

The advent of nanotechnology has created a demand for precision-machined substrates so that ‘bottom-up’ nanomanufacturing processes can be used to produce functional products at the nanoscale. However, machining processes must be scaled down by an order of magnitude that requires very stable desktop machine tools to produce precision-machined substrates using cutting tools that are rotated at speeds in excess of one million revolutions per minute. Therefore, the mechanics of chip formation at this scale are critical when one considers the effect of chip formation on the generation of surface roughness on the substrate. The tight curl of a machined chip in orthogonal machining appears to be part of the primary shear process. It is also known that transient tight curl occurs before a secondary shear zone develops ahead of the removal of the chip from the cutting zone. However, continuum models predict that curled chips incorporate stresses due to the establishment of a secondary shear zone. A model is presented in terms of the heterogeneous aspects of continuous chip formation, which shows very good agreement with experimental data.

Sign in / Sign up

Export Citation Format

Share Document