scholarly journals Formulation of the Effect of Different Alloying Elements on the Tensile Strength of the in situ Al-Mg2Si Composites

Metals ◽  
2015 ◽  
Vol 5 (1) ◽  
pp. 371-382 ◽  
Author(s):  
Halil Kurt ◽  
Murat Oduncuoglu
Keyword(s):  
Tensile Strength ◽  
Alloying Elements

scholarly journals Study on Microstructure and In Situ Tensile Deformation Behavior of Fe-25Mn-xAl-8Ni-C Alloy Prepared by Vacuum Arc Melting

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 814
Author(s):  
Yaping Bai ◽  
Meng Li ◽  
Chao Cheng ◽  
Jianping Li ◽  
Yongchun Guo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Deformation Behavior ◽  
Tensile Deformation ◽  
Austenite Phase ◽  
Vacuum Arc ◽  
Al Content ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Tensile Deformation Behavior

In this study, Fe-25Mn-xAl-8Ni-C alloys (x = 10 wt.%, 11 wt.%, 12 wt.%, 13 wt.%) were prepared by a vacuum arc melting method, and the microstructure of this series of alloys and the in situ tensile deformation behavior were studied. The results showed that Fe-25Mn-xAl-8Ni-C alloys mainly contained austenite phase with a small amount of NiAl compound. With the content of Al increasing, the amount of austenite decreased while the amount of NiAl compound increased. When the Al content increased to 12 wt.%, the interface between austenite and NiAl compound and austenitic internal started to precipitate k-carbide phase. In situ tensile results also showed that as the content of Al increased, the alloy elongation decreased gradually, and the tensile strength first increased and then decreased. When the Al content was up to 11 wt.%, the elongation and tensile strength were 2.6% and 702.5 MPa, respectively; the results of in situ tensile dynamic observations show that during the process of stretching, austenite deformed first, and crack initiation mainly occurred at the interface between austenite and NiAl compound, and propagated along the interface, resulting in fracture of the alloy.

scholarly journals Enhanced Tensile Strength of Monolithic Epoxy with Highly Dispersed TiO2-Graphene Nanocomposites

2021 ◽  
Vol 5 (7) ◽  
pp. 191
Author(s):  
Yanshuai Wang ◽  
Siyao Guo ◽  
Biqin Dong ◽  
Feng Xing
Keyword(s):  
Tensile Strength ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Chemical Properties ◽  
High Mechanical Property ◽  
Graphene Nanocomposites ◽  
Highly Dispersed ◽  
Dispersion State ◽  
Physical And Chemical

The functionalization of graphene has been reported widely, showing special physical and chemical properties. However, due to the lack of surface functional groups, the poor dispersibility of graphene in solvents strongly limits its engineering applications. This paper develops a novel green “in-situ titania intercalation” method to prepare a highly dispersed graphene, which is enabled by the generation of the titania precursor between the layer of graphene at room temperature to yield titania-graphene nanocomposites (TiO2-RGO). The precursor of titania will produce amounts of nano titania between the graphene interlayers, which can effectively resist the interfacial van der Waals force of the interlamination in graphene for improved dispersion state. Such highly dispersed TiO2-RGO nanocomposites were used to modify epoxy resin. Surprisingly, significant enhancement of the mechanical performance of epoxy resin was observed when incorporating the titania-graphene nanocomposites, especially the improvements in tensile strength and elongation at break, with 75.54% and 176.61% increases at optimal usage compared to the pure epoxy, respectively. The approach presented herein is easy and economical for industry production, which can be potentially applied to the research of high mechanical property graphene/epoxy composite system.

Effect of Small Iron, Chromium and Boron Additions as Alloying Elements on Microstructure and Mechanical Properties of Ni3Al

2007 ◽  
Vol 23 ◽  
pp. 123-126
Author(s):  
Radu L. Orban ◽  
Mariana Lucaci
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Alloying Elements ◽  
Alloyed Powder ◽  
Mechanically Alloyed ◽  
Powder Mixtures ◽  
B Additions ◽  
Strength And Ductility ◽  
Iron Chromium

This paper investigates the effect of Fe, Cr and B additions, in small proportions, as alloying elements in Ni3Al with the purpose to reduce its intrinsic fragility and extrinsic embrittlement and to enhance, in the same time, its mechanical properties. It represents a development of some previous research works of the authors, proving that Ni3Al-Fe-Cr-B alloys obtained by reactive synthesis (SHS) starting from Mechanically Alloyed powder mixtures have superior both room temperature tensile strength and ductility, and compression ones at temperatures up to 800 °C, than pure Ni3Al. These create premises for their using as superalloys substitutes.

Study on Mechanical Properties of AA6351 Alloy Reinforced with Titanium Di-Boride (TiB2) Composite by In Situ Casting Method

2015 ◽  
Vol 787 ◽  
pp. 583-587 ◽  
Author(s):  
V. Mohanavel ◽  
K. Rajan ◽  
K.R. Senthil Kumar
Keyword(s):  
Tensile Strength ◽  
Aluminum Matrix ◽  
Aluminum Matrix Composites ◽  
Scanning Electron Micrographs ◽  
Matrix Composites ◽  
X Ray Diffraction ◽  
In Situ Reaction ◽  
Halide Salts ◽  
Scanning Electron

In the present study, an aluminum alloy AA6351 was reinforced with different percentages (1, 3 and 5 wt %) of TiB2 particles and they were successfully fabricated by in situ reaction of halide salts, potassium hexafluoro-titanate and potassium tetrafluoro-borate, with aluminium melt. Tensile strength, yield strength and hardness of the composite were investigated. In situ reaction between the inorganic salts K2TiF6 and KBF4 to molten aluminum leads to the formation of TiB2 particles. The prepared aluminum matrix composites were characterized using X-ray diffraction and scanning electron microscope. Scanning electron micrographs revealed a uniform dispersal of TiB2 particles in the aluminum matrix. The results obtained indicate that the hardness and tensile strength were increased with an increase in weight percentages of TiB2 contents.

Test Methods for Mechanical Properties of Structural Adhesives

2010 ◽  
Vol 97-101 ◽  
pp. 814-817 ◽  
Author(s):  
Jun Deng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Elastic Modulus ◽  
Butt Joint ◽  
Test Methods ◽  
Joint Specimen ◽  
Lap Shear ◽  
Better Than

One of the greatest drawbacks to predicting the behaviour of bonded joints has been the lack of reliable data on the mechanical properties of adhesives. In this study, methods for determining mechanical properties of structural adhesive were discussed. The Young’s modulus, Poisson’s ratio and tensile strength of the adhesive were tested by dogbone specimens (bulk form) and butt joint specimens (in situ form). The shear modulus and shear strength were test by V-notched specimens (bulk form) and thick adherend lap-shear (TALS) joint specimens (in situ form). The test results show that the elastic modulus provided by the manufacturer is too low, the dogbone specimen is better than the butt joint specimen to test the tensile strength and elastic modulus and the TALS joint specimen is better than the V-notched specimen to test the shear strength.

The Investigation on Aluminium Alloys Automobile Wheel with Low-Titanium Content Produced by Electrolysis

2005 ◽  
Vol 475-479 ◽  
pp. 317-320 ◽  
Author(s):  
Jing Pei Xie ◽  
Ji Wen Li ◽  
Zhong Xia Liu ◽  
Ai Qin Wang ◽  
Yong Gang Weng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminium Alloys ◽  
Solution Treatment ◽  
A356 Alloy ◽  
Aging Treatment ◽  
Titanium Content ◽  
The Matrix ◽  
Automobile Wheel

The in-situ Ti alloying of aluminium alloys was fulfilled by electrolysis, and the material was made into A356 alloy and used in automobile wheels. The results show that the grains of the A356 alloy was refined and the second dendrites arm was shortened due to the in-situ Ti alloying. Trough 3-hour solution treatment and 2-hour aging treatment for the A356 alloy, the microstructures were homogeneous, and Si particles were spheroid and distribute in the matrix fully. The outstanding mechanical properties with tensile strength (σb≥300Mpa) and elongation values (δ≥10%) have been obtained because the heat treatment was optimized. Compared with the traditional materials, tensile strength and elongation were increased by 7.6~14.1% and 7.4~44.3% respectively. The qualities of the automobile wheels were improved remarkably.

Classification of the Modes of Dissociation in Immiscible Cu-Alloy Thin Films

1999 ◽  
Vol 564 ◽  
Author(s):  
K. Barmak ◽  
G. A. Lucadamo ◽  
C. Cabral ◽  
C. Lavoie ◽  
J. M. E. Harper
Keyword(s):  
Thin Films ◽  
Driving Forces ◽  
Texture Evolution ◽  
Substantial Reduction ◽  
Alloying Elements ◽  
X Ray Diffraction ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Evolution Of Microstructure

AbstractWe have found the dissociation behavior of immiscible Cu-alloy thin films to fall into three broad categories that correlate most closely with the form of the Cu-rich end of the binary alloy phase diagrams. The motivation for these studies was to use the energy released by the dissociation of an immiscible alloy, in addition to other driving forces commonly found in thin films and lines, to promote grain growth and texture evolution. In this work, the dissociation behavior of eight dilute (3.3 ± 0.5 at% solute) binary Cu-systems was investigated, with five alloying elements selected from group VB and VIB, two from group VillA, and one from group 1B. These alloying elements are respectively V, Nb, Ta, Cr, Mo, Fe, Ru and Ag. Several experimental techniques, including in situ resistance and stress measurements as well as in situ synchrotron x-ray diffraction, were used to follow the progress of solute precipitation in approximately 500 nm thick films. In addition, transmission electron microscopy was used to investigate the evolution of microstructure of Cu(Ta) and Cu(Ag). For all eight alloys, dissociation occurred upon heating, with the rejection of solute and evolution of microstructure and texture often occurring in multiple steps that range over several hundred degrees between approximately 100 and 900°C. However, in most cases, substantial reduction in resistivity of the films took place at temperatures of interest to metallization schemes, namely below 400°C.

Mechanical And Superconducting Properties Of Cu-Nb3Sn In Situ Produced Composite Wires

1981 ◽  
Vol 12 ◽  
Author(s):  
A. Kolb-Telieps ◽  
B.L. Mordike ◽  
M. Mrowiec
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Wide Temperature Range ◽  
Volume Fraction ◽  
Superconducting Properties ◽  
Temperature Range ◽  
Composite Wires ◽  
Strength And Ductility

ABSTRACTCu-Nb composite wires were produced from powder, electrolytically coated with tin and annealed to convert the Nb fibres to Nb 3Sn. The content was varied between 10 wt % and 40 wt %. The superconducting properties of the wires were determined. The mechanical properties, tensile strength, yield strength and ductility were measured as a function of volume fraction and deformation over a wide temperature range. The results are compared with those for wires produced by different techniques.

Sign in / Sign up

Export Citation Format

Share Document