scholarly journals Analysis of Tribological Properties in Disks of AA-5754 and AA-5083 Aluminium Alloys Previously Processed by Equal Channel Angular Pressing and Isothermally Forged

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 938
Author(s):  
Carmelo J. Luis Pérez ◽  
Rodrigo Luri Irigoyen ◽  
Ignacio Puertas Arbizu ◽  
Daniel Salcedo Pérez ◽  
Javier León Iriarte ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
Mean Value ◽  
Wear Behaviour ◽  
Volume Loss ◽  
Angular Pressing ◽  
Ring Configuration ◽  
Ecap Process ◽  
Initial States ◽  
Accumulated Deformation

In the present study, the wear behaviour of two aluminium alloys (AA-5754 and AA-5083) is analysed where these have been previously processed by severe plastic deformation (SPD) with equal channel angular pressing (ECAP). In order to achieve the objectives of this study, several disks made of these alloys are manufactured by isothermal forging from different initial states. The microstructures of the initial materials analysed in this study have different accumulated deformation levels. In order to compare the properties of the nanostructured materials with those which have not been ECAP-processed, several disks with a height of 6 mm and a diameter of 35 mm are manufactured from both aluminium alloys (that is, AA-5754 and AA-5083) isothermally forged at temperatures of 150 and 200 °C, respectively. These thus-manufactured disks are tested under a load of 0.6 kN, which is equivalent to a stress mean value of 18 MPa, and at a rotational speed of 200 rpm. In order to determine the wear values, the disks are weighed at the beginning, at 10,000 revolutions, at 50,000 revolutions and at 100,000 revolutions, and then the volume-loss values are calculated. This study was carried out using specific equipment, which may be considered to have a block-on-ring configuration, developed for testing in-service wear behaviour of mechanical components. From this, the wear coefficients for the two materials at different initial states are obtained. In addition, a comparison is made between the behaviour of the previously ECAP-processed aluminium alloys and those that are non-ECAP-processed. A methodology is proposed to determine wear coefficients for the aluminium alloys under consideration, which may be used to predict the wear behaviour. It is demonstrated that AA-5754 and AA-5083 aluminium alloys improve wear behaviour after the ECAP process compared to that obtained in non-ECAP-processed materials.

Numerical Analysis of the Microstructure and Mechanical Properties Evolution during Equal Channel Angular Pressing

2010 ◽  
Vol 638-642 ◽  
pp. 1940-1945
Author(s):  
Lechoslaw Trebacz ◽  
Henryk Paul ◽  
Łukasz Madej ◽  
Maciej Pietrzyk
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
New Technology ◽  
Strength Properties ◽  
Detailed Understanding ◽  
Fine Grained ◽  
Finite Element Software ◽  
Angular Pressing ◽  
Ecap Process ◽  
The Subject

The development of the new technology for manufacturing of multi layer aluminium based materials for heat radiators is the subject of this work. Modern aluminium alloys can be specially processed in a controlled manner to obtain nano(mikro) structures. These ultra fine grained structures play a significant role because they provide a possibility to obtain final product that is characterized by elevated strength properties and, at the same time, good anticorrosion and soldering properties. A detailed understanding of these ultra fined structures using a combination of numerical modelling and experimental analysis is presented in this paper. Particular attention is put on implementation of the microstructure evolution model into the finite element software to simulate Equal Channel Angular Pressing (ECAP) process. Examples of the obtained results are presented and discussed.

Effect of Equal-Channel Angular Pressing (ECAP) on Creep in Aluminium Alloys

2007 ◽  
Vol 539-543 ◽  
pp. 2904-2909 ◽  
Author(s):  
Vàclav Sklenička ◽  
Jiří Dvořák ◽  
Marie Kvapilová ◽  
Milan Svoboda ◽  
Petr Král ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
Creep Resistance ◽  
Room Temperature ◽  
Creep Behaviour ◽  
Coarse Grained ◽  
Pure Aluminium ◽  
Creep Tests ◽  
Angular Pressing ◽  
Compression Creep

This paper examines the effect of equal-channel angular pressing (ECAP) on creep behaviour of pure aluminium, binary Al-0.2wt.%Sc alloy and ternary Al-3wt.%Mg-0.2wt.%Sc alloy. The ECAP was conducted at room temperature with a die that had a 90° angle between the channels and 8 repetitive ECAP passes followed route BC. Constant stress compression creep tests were performed at 473 K and stresses ranging between 16 to 80 MPa on ECAP materials and, for comparison purposes, on the initial coarse-grained materials. The results showed that the creep resistance of the ECAP processed Al-Sc and Al-Mg-Sc alloys was markedly deteriorated with respect to unpressed coarse-grained materials.

scholarly journals Investigation on the Microstructure of ECAP-Processed Iron-Aluminium Alloys

Materials ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 219
Author(s):  
Bernd-Arno Behrens ◽  
Kai Brunotte ◽  
Tom Petersen ◽  
Roman Relge
Keyword(s):  
Grain Refinement ◽  
Aluminium Alloys ◽  
Aluminium Content ◽  
Microstructure Development ◽  
Chamber Furnace ◽  
Fine Grained ◽  
Angular Pressing ◽  
Ecap Process ◽  
Average Grain Size ◽  
Forming Temperature

The present work deals with adjusting a fine-grained microstructure in iron-rich iron-aluminium alloys using the ECAP-process (Equal Channel Angular Pressing). Due to the limited formability of Fe-Al alloys with increased aluminium content, high forming temperatures and low forming speeds are required. Therefore, tool temperatures above 1100 °C are permanently needed to prevent cooling of the work pieces, which makes the design of the ECAP-process challenging. For the investigation, the Fe-Al work pieces were heated to the respective hot forming temperature in a chamber furnace and then formed in the ECAP tool at a constant punch speed of 5 mm/s. Besides the chemical composition (Fe9Al, Fe28Al and Fe38Al (at.%—Al)), the influences of a subsequent heat treatment and the holding time on the microstructure development were investigated. For this purpose, the average grain size of the microstructure was measured using the AGI (Average Grain Intercept) method and correlated with the aforementioned parameters. The results show that no significant grain refinement could be achieved with the parameters used, which is largely due to the high forming temperature significantly promoting grain growth. The holding times in the examined area do not have any influence on the grain refinement.

Processing of Copper by Equal Channel Angular Pressing (ECAP) – Microstructure Investigations

2015 ◽  
Vol 641 ◽  
pp. 286-293
Author(s):  
Beata Leszczyńska-Madej ◽  
Maria W. Richert ◽  
Agnieszka Hotloś ◽  
Jacek Skiba
Keyword(s):  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Subgrain Size ◽  
Pure Copper ◽  
Shear Bands ◽  
Angular Pressing ◽  
Ecap Process ◽  
Transmission Electron ◽  
Different Types ◽  
Diffraction Patterns

The present study attempts to apply Equal-Channel Angular Pressing (ECAP) to 99.99% pure copper. ECAP process was realized at room temperature for 4, 8 and 16 passes through route BC using a die having angle of 90°. The microstructure of the samples was investigated by means both light and transmission electron microscopy. Additionally the microhardness was measured and statistical analysis of the grains and subgrains was performed. Based on Kikuchi diffraction patterns misorientation was determined. There were some different types of bands in the microstructure after deformation. The shear bands, bands and in the submicron range the microshear bands and microbands are a characteristic feature of the microstructure of copper. Also characteristic was increasing of the number of bands with increasing of deformation and mutually crossing of the bands. The intersection of a bands and microbands leads to the formation of new grains with the large misorientation angle. The measured grain/subgrain size show, that the grain size is maintained at a similar level after each stage of deformation and is equal to d = 0.25 – 0.32 μm.

Numerical Simulation of Microstructure Evolution in AZ31 Magnesium Alloy during Equal Channel Angular Pressing

2014 ◽  
Vol 609-610 ◽  
pp. 495-499
Author(s):  
Guo Cheng Ren ◽  
Xiao Juan Lin ◽  
Shu Bo Xu
Keyword(s):  
Finite Element ◽  
Magnesium Alloy ◽  
Equal Channel Angular Pressing ◽  
Microstructure Evolution ◽  
Element Model ◽  
Az31 Magnesium Alloy ◽  
Angular Pressing ◽  
Ecap Process ◽  
Element Simulation ◽  
3D Software

The microstructure and material properties of AZ31 magnesium alloy are very sensitive to process parameters, which directly determine the service properties. To explore and understand the deformation behavior and the optimization of the deformation process, the microstructure evolution during equal channel angular pressing was predicted by using the DEFORM-3D software package at different temperature. To verify the finite element simulation results, the microstructure across the transverse direction of the billet was measured. The results show that the effects strain and deformation temperatures on the microstructure evolution of AZ31 magnesium during ECAP process are significant, and a good agreement between the predicted and experimental results was obtained, which confirmed that the derived dynamic recrystallization mathematical models can be successfully incorporated into the finite element model to predict the microstructure evolution of ECAP process for AZ31 magnesium.

scholarly journals PERUBAHAN NILAI KEKERASAN DAN KONDUKTIVITAS LISTRIK ALUMINIUM AKIBAT PROSES EQUAL CHANNEL ANGULAR PRESSING (ECAP)

ROTASI ◽  
2014 ◽  
Vol 16 (4) ◽  
pp. 41
Author(s):  
Rusnaldy Rusnaldy ◽  
Norman Iskandar ◽  
Muhammad Khairul Rais ◽  
Wisnu Tri Erlangga
Keyword(s):  
Electrical Conductivity ◽  
Plastic Deformation ◽  
Equal Channel Angular Pressing ◽  
Hardness Test ◽  
Hardness Measurement ◽  
Optical Microscope ◽  
Pure Aluminium ◽  
Angular Pressing ◽  
Ecap Process ◽  
Number Of Passes

In current study, Equal Channel Angular Pressing (ECAP) process was applied to pure aluminium rod. The effect of the number of passes on hardness and electrical conductivity ECAP samples was investigated. The dimensions of ECAP die for 12 mmm diameter workpieces are designed with intersect angle of 120o. The experiments were carried out by using samples cut from an ingot and a rod and machined to a size of 12 mm in diameter and 50 mm in length. The workpiece was pressed into the ECAP die up to 7 passes at room temperature.After deformation, all samples were subjected to a hardness test, an electrical conductivity test and for optical microscope study. The hardness measurement of the ECAP samples suggested that enhanced hardness would be obtained by repeating ECAP process.Increasing the electrical conductivity of the ECAP samples indicatesthat there is no dislocation formation due to increasing plastic deformation in ECAP process

Evaluation Grain Homogeneity of Aluminium after ECAP Process by ECAP Geometry Analysis Using Taguchi Method

2013 ◽  
Vol 594-595 ◽  
pp. 896-901
Author(s):  
Aminnudin ◽  
Pratiko ◽  
Anindito Purnowidodo ◽  
Yudy Surya Irawan ◽  
Shigeyuki Haruyama ◽  
...  
Keyword(s):  
Grain Size ◽  
Taguchi Method ◽  
Equal Channel Angular Pressing ◽  
Channel Angle ◽  
Angular Pressing ◽  
Fine Grain ◽  
Ecap Process ◽  
Fillet Radius ◽  
Geometry Analysis

Grain size and homogeneity are influence to aluminium properties, Equal channel angular pressing (ECAP) can produce aluminium with ultra fine grain Size (UFG). The grain size is depends on ECAP Dies geometry (Channel angle Φ, Fillet radius ψ) and friction, taguchi method used to find the optimum dies geometry its can produce smaller grain size and homogeny. Modeling done with channel angels 90, 105 and 120°, fillet radius (inside) 1.5, 5,0 and 10 mm ; fillet radius (outside) 1.5, 5,0 and 10 mm and friction 0, 0,025 and 0,05. Modeling used L9 taguchi matrix, the most homogeny dies is ECAP dies with channel angel 105°, fillet radius (inside) 10 mm ; fillet radius (outside) 0 mm and friction 0,025

Mechanical Properties and Texture Evolution of AZ31 Mg Alloy during Equal Channel Angular Pressing

2005 ◽  
Vol 475-479 ◽  
pp. 545-548 ◽  
Author(s):  
Hyo Tae Jeong ◽  
Woo Jin Kim
Keyword(s):  
Mechanical Properties ◽  
Grain Refinement ◽  
Equal Channel Angular Pressing ◽  
Texture Evolution ◽  
Fiber Texture ◽  
Mg Alloy ◽  
Angular Pressing ◽  
Ecap Process ◽  
Az31 Mg Alloy ◽  
Similar Texture

Microstructure and texture evolution in the AZ31 Mg alloy subject to equal channel angular pressing (ECAP) have been investigated and correlated with the mechanical properties. When AZ31 Mg alloy was ECAPed up to 8 passes following the route Bc, grain refinement occurred effectively. Texture was also changed during ECAP. The original fiber texture of the extruded AZ31 Mg alloy changed to a new texture component of ] 1 3 2 5 )[ 1 1 01 ( , and the texture of ] 1 3 2 5 )[ 1 1 01 ( orientation was rotated to ] 0 2 5 7 )[ 6 4 13 ( orientation after 6-pass ECAP process. The variation of the strength with the pass number was explained by the texture and grain size. The strength data of AZ31 Mg alloys followed the standard Hall-Petch relationship when the similar texture was retained during the ECAP process. Otherwise the effect of texture on strength was dominant over the strengthening due to grain refinement.

Mechanical Properties of Al6061 Processed by Equal Channel Angular Pressing

2012 ◽  
Vol 585 ◽  
pp. 392-396 ◽  
Author(s):  
Ankit Sahai ◽  
Rahul Swarup Sharma ◽  
K. Hans Raj ◽  
Narinder Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Equal Channel Angular Pressing ◽  
Manufacturing Industry ◽  
High Strength ◽  
Load Variations ◽  
Outer Corner ◽  
Angular Pressing ◽  
Ecap Process ◽  
Circular Specimen ◽  
Number Of Passes

The severe plastic deformation (SPD) is an effective approach for producing bulk nanostructured materials. The Equal Channel Angular Pressing (ECAP) is the most efficient SPD solution for achieving ultra-fined grained (UFG) material as billet undergoes severe and large deformation. The process parameters of ECAP (Channel Angle, angle of curvature, friction, number of passes, etc) influences major impact on the properties. In present work, the ECAP process is performed by pressing a specimen through a die consisting of two intersecting channels meeting at an angle φ and outer corner meeting at an angle ψ. Experiments with a circular specimen of Al6061 were conducted to investigate the changes in mechanical properties upto 2 passes. 3-D finite element simulations were also performed using metal forming software FORGE to study the evolution of strain in the specimen during the ECAP process. Simulation results were investigated by comparing them with experimental measured data in terms of load variations. The present work clearly shows that ECAP caused accentuated increase in Al6061 hardness and tensile strength during multi-pass processing. This study is beneficial in developing high quality, high strength products in manufacturing industry on account of its ability to change microstructure of materials.

Sign in / Sign up

Export Citation Format

Share Document