scholarly journals Study on the Hot Deformation Characterization of Borated Stainless Steel by Hot Isostatic Pressing

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7110
Author(s):  
Yanbin Pei ◽  
Xuanhui Qu ◽  
Qilu Ge ◽  
Tiejun Wang
Keyword(s):  
Stainless Steel ◽  
Hot Deformation ◽  
True Strain ◽  
Hot Isostatic Pressing ◽  
Microstructural Analysis ◽  
Critical Conditions ◽  
True Strain Rate ◽  
Isostatic Pressing ◽  
Different Temperatures ◽  
Borated Stainless Steel

Borated stainless steel (BSS) specimens have a boron content of 1.86 wt%, and are prepared by hot isostatic pressing (HIP) conducted at different temperatures, ranging from 1000 to 1100 °C and a constant true strain rate (0.01, 0.1, 1 and 10 s−1). These tests, with observations and microstructural analysis, have achieved the hot deformation characteristics and mechanisms of BSS. In this research, the activation energy (Q) and Zener–Hollomon parameter (Z) were contrasted against the flow curves: Q = 442.35 kJ/mol. The critical conditions associated with the initiation of dynamic recrystallization (DRX) for BSS were precisely calculated based on the function between the strain hardening rate with the flow stress: at different temperatures from 1000 to 1100 °C: the critical stresses were 146.69–254.77 MPa and the critical strains were 0.022–0.044. The facts show that the boron-containing phase of BSS prevented the onset of DRX, despite the saturated boron in the austenite initiated DRX. The microstructural analysis showed that hot deformation promoted the generation of borides, which differed from the initial microstructure of HIP. The inhomogeneous distribution of elements in the boron-containing phase was caused by hot compression.

scholarly journals Effect of Heat Treatment Temperature on Microstructure and Properties of PM Borated Stainless Steel Prepared by Hot Isostatic Pressing

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4646
Author(s):  
Yanbin Pei ◽  
Xuanhui Qu ◽  
Qilu Ge ◽  
Tiejun Wang
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Heat Treatment Temperature ◽  
Hot Isostatic Pressing ◽  
Fracture Morphology ◽  
Treatment Temperature ◽  
Isostatic Pressing ◽  
Different Temperatures ◽  
Strength And Plasticity ◽  
Borated Stainless Steel

Borated stainless steel (BSS) with a boron content of 1.86% was prepared by a powder metallurgy process incorporating atomization and hot isostatic pressing. After solution quenching at 900–1200 °C, the phase composition of the alloy was studied by quantitative X-ray diffraction phase analysis. The microstructure, fracture morphology, and distributions of boron, chromium, and iron in grains of the alloy were analyzed by field-emission scanning electron microscopy with secondary electron and energy-dispersive spectroscopy. After the coupons were heat treated at different temperatures ranging from 900 to 1200 °C, the strength and plasticity were tested, and the fracture surfaces were analyzed. Undergoing heat treatment at different temperatures, the phases of the alloy were austenite and Fe1.1Cr0.9B0.9 phase. Since the diffusion coefficients of Cr, Fe, and B varied at different temperatures, the distribution of elements in the alloy was not uniform. The alloy with good strength and plasticity can be obtained when the heat treatment temperature of alloy ranged from 1000 to 1150 °C while the tensile strength was about 800 MPa, with the elongation standing about 20%.

scholarly journals Study of Microstructure Features and Properties of Metals Obtained by Hot Isostatic Pressing

2021 ◽  
Vol 24 (4) ◽  
pp. 4-10
Author(s):  
A.A. Khlybov ◽  
D.A. Ryabov ◽  
M.S. Anosov ◽  
E.S. Belyaev
Keyword(s):  
Fractal Dimension ◽  
Relative Density ◽  
Metal Powder ◽  
Hot Isostatic Pressing ◽  
Microstructural Analysis ◽  
Fractal Dimensionality ◽  
Spherical Particles ◽  
Metal Powders ◽  
Isostatic Pressing ◽  
Different Temperatures

The aim of this research is to study the features of the structure and properties of alloys obtained using the technology of hot isostatic pressing (HIP) of metal powders. The study was carried out in the temperature range of interruption of the HIP cycle from 670 to 1150 °C on alloys 08Cr18Ni10Ti and Cr12MoV. For processing images of microstructures and assessing their fractal dimension, software has been developed in the MATLAB environment. The results of microstructural analysis of the metals under study showed that complete sintering of powders is observed at a HIP temperature of 1150 °C; at lower temperatures, pores and unsintered spherical particles of metal powder are observed in the microstructure of the alloys. The grain size of alloys obtained by HIP is determined, first of all, by the size of the initial fraction of the metal powder. Based on the results of evaluating the density of alloys obtained at different temperatures of the HIP, a relationship was established between the relative density of the alloy and the process temperature. Based on the results of fractal analysis, the relationship between the fractal dimensionality of the microstructure of the alloy and the HIP temperature and the relative density of the metals under study has been established. The obtained dependences are linear. The error in estimating the relative density from the obtained dependencies is, on average, 5 %. The data obtained in the course of the study make it possible to estimate the density of metals obtained by hot isostatic pressing of metal powders by evaluating the fractal dimension of the microstructure image.

scholarly journals Evolution of Microstructure and Elements Distribution of Powder Metallurgy Borated Stainless Steel during Hot Isostatic Pressing

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 19
Author(s):  
Yanbin Pei ◽  
Xuanhui Qu ◽  
Qilu Ge ◽  
Tiejun Wang
Keyword(s):  
Grain Size ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Powder Metallurgy ◽  
Relative Density ◽  
Hot Isostatic Pressing ◽  
Elemental Distribution ◽  
Isostatic Pressing ◽  
Average Grain Size ◽  
Borated Stainless Steel

prepared by powder metallurgy process incorporating atomization and hot isostatic pressing (HIP) sintering at six different temperatures from 600 to 1160 °C, borated stainless steel (BSS) containing boron content of 1.86 wt% was studied. The phase of BSS, relative density of different temperature, microstructure, elemental distribution, and mechanical properties were tested and analyzed. The phases of the alloy were calculated by the Thermo-Calc (2021a, Thermo-Calc Software, Solna, Sweden) and studied by quantitative X-ray diffraction phase analysis. The distributions of boron, chromium, and iron in grains of the alloy were analyzed by scanning electron microscopy and transmission electron microscope. The grain size distributions and average grain sizes were calculated for the boron-containing phases at 900, 1000, 1100, and 1160 °C, as well as the average grain size of the austenite phase at 700 and 1160 °C. After undergoing HIP sintering at 900, 1000, 1100, and 1160 °C, respectively, the tensile strength and ductility of the alloy were tested, and the fracture surfaces were analyzed. It was found that the alloy consisted of two phases (austenite and boron-containing phase) when HIP sintering temperature was higher than 900 °C, and the relative density of the prepared alloys was higher than 99% when HIP temperature was higher than 1000 °C. According to the boron-containing phase grain size distribution and microstructure analysis, the boron-containing phase precipitated both inside the austenite matrix and at the grain boundaries and its growth mechanism was divided into four steps. The tensile strength and elongation of alloy were up to 776 MPa and 19% respectively when the HIP sintering was at 1000 °C.

Producing HP Pump Barrels Utilizing Powder Metallurgy and Hot Isostatic Pressing

2009 ◽  
Author(s):  
Martin Bjurstro¨m ◽  
Carl-Gustaf Hjorth
Keyword(s):  
High Pressure ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Hot Isostatic Pressing ◽  
Austenitic Stainless Steels ◽  
Pressure Vessels ◽  
Uniform Structure ◽  
Isostatic Pressing ◽  
Near Net Shape ◽  
Hip Process

The fabrication of near net shape powder metal (PM) components by hot isostatic pressing (HIP) has been an important manufacturing technology for steel and stainless steel alloys since about 1985. The manufacturing process involves inert gas atomization of powder, 3D CAD capsule design, sheet metal capsule fabrication and densification by HIP in very large pressure vessels. Since 1985, several thousand tonnes of parts have been produced. The major applications are found in the oil and gas industry especially in offshore applications, the industrial power generation industry, and traditional engineering industries. Typically, the components replace castings, forgings and fabricated parts and are produced in high alloy grades such as martensitic steels, austenitic stainless steels, duplex (ferritic/austenitic) stainless steels and nickel based superalloys. The application of PM/HIP near net shapes to pump barrels for medium to high pressure use has a number of advantages compared to the traditional forging and welding approach. First, the need for machining of the components is reduced to a minimum and welding during final assembly is reduced substantially. Mechanical properties of the PM/HIP parts are isotropic and equal to the best forged properties in the flow direction. This derives from the fine microstructure using powder powder and the uniform structure from the HIP process. Furthermore, when using the PM HIP process the parts are produced near net shape with supports, nozzles and flanges integrated. This significantly reduces manufacturing lead-time and gives greater design flexibility which improves cost for the final component. The PM HIP near net shape route has received approval from ASTM, NACE and API for specific steel, stainless steel and nickel base alloys. This paper reviews the manufacturing sequence for PM near net shapes and discusses the details of several successful applications. The application of the PM/HIP process to high pressure pump barrels is highlighted.

scholarly journals Effect of Hot Isostatic Pressing on Porosity and Mechanical Properties of 316 L Stainless Steel Prepared by the Selective Laser Melting Method

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4377
Author(s):  
Tomas Cegan ◽  
Marek Pagac ◽  
Jan Jurica ◽  
Katerina Skotnicova ◽  
Jiri Hajnys ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Hot Isostatic Pressing ◽  
Microstructural Analysis ◽  
Scanning Speed ◽  
High Yield ◽  
Laser Method ◽  
Preparation Conditions ◽  
Lower Porosity ◽  
316 L Stainless Steel

The manufacturing route primarily determines the properties of materials prepared by additive manufacturing methods. In this work, the microstructural features and mechanical properties of 316 L stainless steel prepared by the selective laser method have been determined. Three types of samples, (i) selective laser melted (SLM), (ii) selective laser melted and hot isostatic pressed (HIP) and (iii) selective laser melted and heat treated (HT), were characterized. Microstructural analysis revealed that SLM samples were formed by melt pool boundaries with fine cellular–dendritic-type microstructure. This type of microstructure disappeared after HT or HIP and material were formed by larger grains and sharply defined grain boundaries. The SLM-prepared samples contained different levels of porosity depending on the preparation conditions. The open interconnected LOF (lack of fusion) pores were observed in the samples, which were prepared with using of scanning speed 1200 mm/s. The blowhole and keyhole type of porosity were observed in the samples prepared by lower scanning speeds. The HIP caused a significant decrease in internal closed porosity to 0.1%, and a higher pressure of 190 MPa was more effective than the usually used pressure of 140 MPa, but for samples with open porosity, HIP was not effective. The relatively high yield strength of 570 MPa, tensile strength of 650 MPa and low ductility of 30–34% were determined for SLM samples with the lower porosity content than 1.3%. The samples after HIP showed lower yield strengths than after SLM (from 290 to 325 MPa) and relatively high ductility of 47.8–48.5%, regardless of the used SLM conditions.

Producing HP Pump Barrels Utilizing Powder Metallurgy and Hot Isostatic Pressing

2009 ◽  
Author(s):  
Martin Bjurstro¨m ◽  
Carl-Gustaf Hjorth
Keyword(s):  
High Pressure ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Hot Isostatic Pressing ◽  
Austenitic Stainless Steels ◽  
Pressure Vessels ◽  
Uniform Structure ◽  
Isostatic Pressing ◽  
Near Net Shape ◽  
Hip Process

The fabrication of near net shape powder metal (PM) components by hot isostatic pressing (HIP) has been an important manufacturing technology for steel and stainless steel alloys since about 1985. The manufacturing process involves inert gas atomization of powder, 3D CAD capsule design, sheet metal capsule fabrication and densification by HIP in very large pressure vessels. Since 1985, several thousand tonnes of parts have been produced. The major applications are found in the oil and gas industry especially in offshore applications, the industrial power generation industry, and traditional engineering industries. Typically, the components replace castings, forgings and fabricated parts and are produced in high alloy grades such as martensitic steels, austenitic stainless steels, duplex (ferritic/austenitic) stainless steels and nickel based superalloys. The application of PM/HIP near net shapes to pump barrels for medium to high pressure use has a number of advantages compared to the traditional forging and welding approach. First, the need for machining of the components is reduced to a minimum and welding during final assembly is reduced substantially. Mechanical properties of the PM/HIP parts are isotropic and equal to the best forged properties in the flow direction. This derives from the fine microstructure using powder powder and the uniform structure from the HIP process. Furthermore, when using the PM HIP process the parts are produced near net shape with supports, nozzles and flanges integrated. This significantly reduces manufacturing lead-time and gives greater design flexibility which improves cost for the final component. The PM HIP near net shape route has received approval from ASTM, NACE and API for specific steel, stainless steel and nickel base alloys. This paper reviews the manufacturing sequence for PM near net shapes and discusses the details of several successful applications. The application of the PM/HIP process to high pressure pump barrels is highlighted.

Sign in / Sign up

Export Citation Format

Share Document