scholarly journals Porosity of Calcium Silicate Hydrates Synthesized from Natural Rocks

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5592
Author(s):  
Raimundas Siauciunas ◽  
Giedrius Smalakys ◽  
Tadas Dambrauskas
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Calcium Silicate ◽  
Total Pore Volume ◽  
Simultaneous Thermal Analysis ◽  
Molar Ratio ◽  
Amorphous Sio2 ◽  
Calcium Silicate Hydrates ◽  
Bet Analysis

In this work, the suitability of natural raw materials with various modifications of SiO2—granite sawing waste (quartz) and opoka (a mixture of cristobalite, tridymite, quartz, and an amorphous part)—for the 1.13 nm tobermorite and xonotlite synthesis is examined, and their specific surface area, pore diameter and volume, and the predominant pores are determined. Hydrothermal syntheses were carried out at 200 °C for 12 and 72 h from mixtures with a molar ratio of CaO/SiO2 = 1.0. X-ray diffraction analysis, simultaneous thermal analysis, and scanning electronic microscopy were used, which showed that in the lime–calcined opoka mixture the formation of crystalline calcium silicate hydrates takes place much faster than in the lime–granite sawing waste mixture. The high reactivity of amorphous SiO2 results in the rapid formation of 1.13 nm tobermorite and xonotlite (12 h). According to Brunauer, Emmet and Taller (BET) analysis data, this product features a specific surface area of ~68 m2/g, a total pore volume of 245·10−3 cm3/g, and has dominating 1–2.5 nm and 5–20 nm diameter pores. This porosity of the material should provide good thermal insulation properties of the products made from it as no air convection occurs in the fine pores.

scholarly journals THE STABILIZING OF ANATASE AEROGEL AT HIGH TEMPERATURE

2010 ◽  
Vol 4 (2) ◽  
pp. 110-116 ◽  
Author(s):  
Silvester Tursiloadi ◽  
Hiroshi Hirashima
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Anatase Phase ◽  
Total Pore Volume ◽  
Average Pore ◽  
Amorphous Sio2 ◽  
Bet Specific Surface Area ◽  
Sio2 Aerogel

Stable anatase is attractive to its notable functions for photo catalysis and photon-electron transfer.   Stable anatase TiO­2 containing amorphous SiO2 aerogel was prepared by hydrolysis of Ti (OC3H7)4 and Si (OC3H7)4 in a 2-propanol solution with acid catalyst. The solvent in wet gels was supercritically extracted in CO2 at 60 oC and 22 Mpa. Thermal evolutions of the microstructure of the gels were evaluated by TGA-DTA, N2 adsorption and XRD. A stable anatase TiO2 containing amorphous SiO2 aerogel with a BET specific surface area of 365 m2/g and a total pore volume of 0.20 cm3/g was obtained as prepared condition. The anatase phase was stable after calcination up to 1000 oC, and BET specific surface area, total pore volume and average pore diameter did not change significantly after calcination up to 900 oC.   Keywords: Supercritical extraction, sol-gel, aerogel, stable anatase structure

scholarly journals Carbazole-functionalized hyper-cross-linked polymers for CO2 uptake based on Friedel–Crafts polymerization on 9-phenylcarbazole

2019 ◽  
Vol 15 ◽  
pp. 2856-2863 ◽  
Author(s):  
Dandan Fang ◽  
Xiaodong Li ◽  
Meishuai Zou ◽  
Xiaoyan Guo ◽  
Aijuan Zhang
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Reaction Temperature ◽  
Pore Volume ◽  
Total Pore Volume ◽  
Molar Ratio ◽  
Co2 Uptake ◽  
Bet Specific Surface Area ◽  
Cross Linker

To systematically explore the effects of the synthesis conditions on the porosity of hyper-cross-linked polymers (HCPs), a series of 9-phenylcarbazole (9-PCz) HCPs (P1–P11) has been made by changing the molar ratio of cross-linker to monomer, the reaction temperature T 1, the used amount of catalyst and the concentration of reactants. Fourier transform infrared spectroscopy was utilized to characterize the structure of the obtained polymers. The TG analysis of the HCPs showed good thermal stability. More importantly, a comparative study on the porosity revealed that: the molar ratio of cross-linker to monomer was the main influence factor of the BET specific surface area. Increasing the reaction temperature T 1 or changing the used amount of catalyst could improve the total pore volume greatly but sacrificed a part of the BET specific surface area. Fortunately changing the concentration of reactants could remedy this situation. Slightly changing the concentration of reactants could simultaneously obtain a high surface area and a high total pore volume. The BET specific surface areas of P3 was up to 769 m2 g−1 with narrow pore size distribution and the CO2 adsorption capacity of P11 was up to 52.4 cm3 g−1 (273 K/1.00 bar).

scholarly journals Nanometer Pore Structure Characterization of Taiyuan Formation Shale in the Lin-Xing Area Based on Nitrogen Adsorption Experiments

Minerals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 298
Author(s):  
Chenlong Ding ◽  
Jinxian He ◽  
Hongchen Wu ◽  
Xiaoli Zhang
Keyword(s):  
Specific Surface ◽  
Pore Structure ◽  
Surface Area ◽  
Specific Surface Area ◽  
Shale Gas ◽  
Pore Volume ◽  
Ordos Basin ◽  
Total Pore Volume ◽  
Nitrogen Adsorption ◽  
Taiyuan Formation

Ordos Basin is an important continental shale gas exploration site in China. The micropore structure of the shale reservoir is of great importance for shale gas evaluation. The Taiyuan Formation of the lower Permian is the main exploration interval for this area. To examine the nanometer pore structures in the Taiyuan Formation shale reservoirs in the Lin-Xing area, Northern Shaanxi, the microscopic pore structure characteristics were analyzed via nitrogen adsorption experiments. The pore structure parameters, such as specific surface area, pore volume, and aperture distribution, of shale were calculated; the significance of the pore structure for shale gas storage was analyzed; and the main controlling factors of pore development were assessed. The results indicated the surface area and hole volume of the shale sample to be 0.141–2.188 m2/g and 0.001398–0.008718 cm3/g, respectively. According to the IUPAC (International Union of Pure and Applied Chemistry) classification, mesopores and macropores were dominant in the pore structure, with the presence of a certain number of micropores. The adsorption curves were similar to the standard IV (a)-type isotherm line, and the hysteresis loop type was mainly similar to H3 and H4 types, indicating that most pores are dominated by open type pores, such as parallel plate-shaped pores and wedge-shaped slit pores. The micropores and mesopores provide the vast majority of the specific surface area, functioning as the main area for the adsorption of gas in the shale. The mesopores and macropores provide the vast majority of the pore volume, functioning as the main storage areas for the gas in the shale. Total organic carbon had no notable linear correlation with the total pore volume and the specific surface area. Vitrinite reflectance (Ro) had no notable correlation with the specific surface area, but did have a low “U” curve correlation with the total pore volume. There was no relationship between the quartz content and specific surface area and total pore volume. In addition, there was no notable correlation between the clay mineral content and total specific surface area and total pore volume.

The Influence of Fe/Al Molar Ratio on Microreactor-Based Catalyst Preparation and Carbon Nanotube Preparation

2021 ◽  
Vol 1036 ◽  
pp. 130-136
Author(s):  
Ting Qun Tan ◽  
Lei Geng ◽  
Yan Lin ◽  
Yan He
Keyword(s):  
Carbon Nanotubes ◽  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Small Diameter ◽  
High Specific Surface Area ◽  
Detection Methods ◽  
Molar Ratio ◽  
High Catalytic Activity

In order to prepare carbon nanotubes with high specific surface area, small diameter, low resistivity, high purity and high catalytic activity, the Fe-Mo/Al2O3 catalyst was prepared based on the microreactor. The influence of different Fe/Al molar ratios on the catalyst and the carbon nanotubes prepared was studied through BET, SEM, TEM and other detection methods. Studies have shown that the pore structure of the catalyst is dominated by slit pores at a lower Fe/Al molar ratio. The catalytic activity is the highest when the Fe/Al molar ratio is 1:1, reaching 74.1%. When the Fe/Al molar ratio is 1:2, the catalyst has a higher specific surface area, the maximum pore size is 8.63 nm, and the four-probe resistivity and ash content of the corresponding carbon nanotubes are the lowest. The higher the proportion of aluminum, the higher the specific surface area of the catalyst and the carbon nanotubes, and the finer the diameter of the carbon nanotubes, which gradually tends to relax. The results show that when the Fe/Al molar ratio is 1:2, although the catalytic activity of the catalyst is not the highest, the carbon nanotubes prepared have the best performance.

scholarly journals Tuning the Morphological Properties of Cellulose Aerogels: An Investigation of Salt-Mediated Preparation

2021 ◽  
Author(s):  
Prakash Parajuli ◽  
Sanjit Acharya ◽  
Julia Shamshina ◽  
Noureddine Abidi
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sol Gel ◽  
Earth Metal ◽  
Morphological Properties ◽  
Cellulose Solution ◽  
Bet Analysis ◽  
Sol Gel Transition ◽  
Gel Transition

Abstract In this study, alkali and alkaline earth metal chlorides with different cationic radii (LiCl, NaCl, and KCl, MgCl2, and CaCl2) were used to gain insight into the behavior of cellulose solutions in the presence of salts. The specific focus of the study was evaluation of the effect of salts’ addition on the sol-gel transition of the cellulose solutions and on their ability to form monoliths, as well as evaluation of the morphology (e.g., specific surface area, pore characteristics, and microstructure) of aerocelluloses prepared from these solutions. The effect of the salt addition on the sol-gel transition of cellulose solutions was studied using rheology, and morphology of resultant aerogels was evaluated by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis, while the salt influence on the aerocelluloses’ crystalline structure and thermal stability was evaluated using powder X-Ray Diffraction (pXRD) and Thermogravimetric Analysis (TGA), respectively. The study revealed that the effect of salts’ addition was dependent on the component ions and their concentration. The addition of salts in the amount below certain concentration limit significantly improved the ability of the cellulose solutions to form monoliths and reduced the sol-gel transition time. Salts of lower cationic radii had a greater effect on gelation. However, excessive amount of salts resulted in the formation of fragile monoliths or no formation of gels at all. Analysis of surface morphology demonstrated that the addition of salts resulted in a significant increase in porosity and specific surface area, with salts of lower cationic radii leading to aerogels with much larger (~1.5 and 1.6-fold for LiCl and MgCl2, respectively) specific surface area compared to aerocelluloses prepared with no added salt. Thus, by adding the appropriate salt into the cellulose solution prior to gelation, the properties of aerocelluloses that control material’s performance (specific surface area, density, and porosity) could be tailored for a specific application.

scholarly journals Influence of the Calcination Temperature on the properties of The Alumina as Catalyst Support for Catalysis

Paliva ◽  
2020 ◽  
pp. 155-161
Author(s):  
Tomáš Hlinčík ◽  
Veronika Šnajdrová ◽  
Veronika Kyselová
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Calcination Temperature ◽  
Specific Surface Area ◽  
Catalyst Support ◽  
Chemical Properties ◽  
Total Pore Volume ◽  
Temperature Range ◽  
Calcination Temperatures ◽  
Physical And Chemical

Alumina is commonly used in industrial practice as a catalyst support and it is made from boehmite. Depending on the calcination temperature, this mineral is transformed into various crystalline modifications which have different physical and chemical properties. For this reason, the following parameters were determined at different calcination temperatures: length, width, material hardness, specific surface area and total pore volume. The results show that with increasing calcination temperature there have been significant changes which may be important when using the material as a catalyst support, e.g. in the preparation of catalysts or in the design of cat-alytic reactors. The specific surface area, which decreases in the temperature range 450–800 °C, is an important parameter for the preparation of catalysts, so it is appropriate to choose a temperature of 600 °C, when the specific surface area is above 200 m2·g-1. The effect of calcination temperature on the structural transitions of boehmite was also monitored. The results showed that γ-Al2O3 has the most suitable properties as a catalyst sup-port in the temperature range 450–800 °C.

scholarly journals Structural and fractal characterization of adsorption pores of middle–high rank coal reservoirs in western Yunnan and eastern Guizhou: An experimental study of coals from the Panguan syncline and Laochang anticline

2018 ◽  
Vol 37 (1) ◽  
pp. 251-272 ◽  
Author(s):  
Junjian Zhang ◽  
Chongtao Wei ◽  
Gaoyuan Yan ◽  
Guanwen Lu
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Structural Parameters ◽  
Total Pore Volume ◽  
Type A ◽  
Type B ◽  
Type C

To better understand the structural characteristic of adsorption pores (pore diameter < 100 nm) of coal reservoirs around the coalbed methane production areas of western Yunnan and eastern Guizhou, we analyzed the structural and fractal characteristics of pore size range of 0.40–2.0 nm and 2–100 nm in middle–high rank coals ( Ro,max = 0.93–3.20%) by combining low-temperature N2/CO2 adsorption tests and surface/volume fractal theory. The results show that the coal reservoirs can be divided into three categories: type A ( Ro,max < 2.15%), type B (2.15% <  Ro,max <2.50%), and type C ( Ro,max > 2.15%). The structural parameters of pores in the range from 2 to 100 nm are influenced by the degree of coal metamorphism and the compositional parameters (e.g., ash and volatile matter). The dominant diameters of the specific surface areas are 10–50 nm, 2–50 nm, and 2–10 nm, respectively. The pores in the range from <2 nm provide the largest proportion of total specific surface area (97.22%–99.96%) of the coal reservoir, and the CO2-specific surface area and CO2-total pore volume relationships show a positive linear correlation. The metamorphic degree has a much greater control on the pores (pore diameter less than 2 nm) structural parameters than those of the pore diameter ranges from 2 to 100 nm. Dv1 and Dv2 can characterize the structure of 2–100 nm adsorption pores, and Dv1 (volume heterogeneity) has a positive correlation with the pore structural parameters such as N2-specific surface area and N2-total pore volume. This parameter can be used to characterize volume heterogeneity of 2–10 nm pores. Dv2 (surface heterogeneity) showed type A > type B > type C and was mainly affected by the metamorphism degree. Ds2 can be used to characterize the pore surface heterogeneity of micropores in the range of 0.62–1.50 nm. This parameter has a good correlation with the pore parameters (CO2-total pore volume, CO2-specific surface area, and average pore size) and is expressed as type C < type B < type A. In conclusion, the heterogeneity of the micropores is less than that of the meso- and macropores (2–100 nm). Dv1, Dv2, and Ds2 can be used as effective parameters to characterize the pore structure of adsorption pores. This result can provide a theoretical basis for studying the pore structure compatibility of coal reservoirs in the region.

Comparative Assessment of Effectiveness of Calcium Silicate Dispersions Produced Using Sucrose and Lactose as Components of Composite Cement Binder

2021 ◽  
Vol 1017 ◽  
pp. 11-20
Author(s):  
Evgeny A. Shoshin ◽  
Valeria V. Strokova ◽  
Zheng Mao Ye
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Calcium Silicate ◽  
Setting Time ◽  
Inhibitory Effect ◽  
Main Element ◽  
Residual Content ◽  
Nucleation Effect ◽  
Wide Range

Silicate micro- and nano-additives are multifunctional in relation to cement systems. Their application can solve a wide range of technological problems while maintaining the economic efficiency of technical solutions. The effect of silicate additives and fillers is determined by their level of dispersion, due to which the technologies for producing nano- and submicro-sized dispersed materials are being developed. The combination of mechanochemical synthesis of modified calcium hydrosilicates with subsequent thermolysis makes it possible to produce calcium silicate dispersions (SCD), which differ in polymodality of the fractional composition including submicro (10–7–10–6 m) and microdimensional (≥10–6 m) modes. The main element of the technology is the use of modifying carbohydrate, which acts as a stabilizer of hydrated phases of silicates. A comparative study of SCD produced using sucrose (sSCD) and lactose (lSCD) revealed the effect of these carbohydrates on the properties of sSCD and lSCD, as well as their effectiveness as a component of cementitious composite binder. It was found that the level of adsorption of modifying carbohydrate determines the physical properties of SCD (granulometry, specific surface area). The relatively high residual content of free sucrose (0.24%) in the composition of sSCD prevents the consolidation of silicates nanoparticles formed during the thermolysis, causes a high content of submicro sized fractions and a high specific surface area with sSCD (26.3 ± 0.7 m2/g). Lactose is absorbed by the silicate phase; the residual content of free lactose does not exceed 0.028% of lSCD. The low content of stabilizing carbohydrate contributes to the development of nanoparticle consolidation, a decrease in the specific surface area of lSCD to 13.0 ± 0.2 m2/g and content of submicrosized fractions. The residual content of free carbohydrates and particle size characteristics of sSCD and lSCD determine the nature of their influence on Cement-SCD-based concrete setting and hardening. The presence of residual sucrose in the composition of sSCD and fine fractions determines the competitive nature of the processes of retardation of hardening and acceleration of hardening of the cement system due to the nucleation effect, as a result of which the curve of the setting time is extreme. In addition, the inhibitory effect of sucrose reduces the strength of concrete on the 7th day. By the 28th day, the inhibitory effect of sucrose has been overcome, and concrete samples demonstrate an 18% increase in compressive strength with a sSCD content of 30%. The low content of residual free lactose in the composition of lSCD causes the nucleation effect. As a result, there is a monotonous reduction in the setting time of concrete mix with an increase in the content of lSCD in the composition of HF, as well as a significant increase in concrete strength (up to 127%) on the 7th day. At the same time, on the 28th day the strength of concrete increases slightly

Microstructural and porosimetry analysis of Ag-TiO2intercalated kaolin and diatomite as nanocomposite ceramic materials

Clay Minerals ◽  
2018 ◽  
Vol 53 (4) ◽  
pp. 665-674 ◽  
Author(s):  
Emmanuel Ajenifuja ◽  
Abimbola P.I. Popoola ◽  
Kabir O. Oyedotun ◽  
Olawale Popoola
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Ceramic Materials ◽  
Mineral Particle ◽  
Scanning Calorimetry ◽  
Sintered Ceramic ◽  
Morphological Studies ◽  
Bet Specific Surface Area ◽  
Bet Analysis

ABSTRACTKaolin and diatomite are abundant and widely available geological materials that may immobilize or stabilize functional chemical species on their surfaces for various applications. Acid-treated kaolin and diatomite were intercalated with photocatalyst Ag-TiO2nanoparticles using the sol–gel technique to prepare nanocomposite ceramic materials. The nanocomposites were sintered between 900°C and 1000°C to induce thermal reactions and to enhance nanoparticle–substrate attachment. Chemical and thermal characterizations of the acid-treated materials and intercalated nanocomposites were performed with energy-dispersive X-ray (EDX) analysis and differential scanning calorimetry (DSC), respectively. The Brunauer–Emmett–Teller (BET)-specific surface area and scanning electron microscopy (SEM) were employed for physical and microstructural characterization of the nanocomposites, respectively. Morphological studies revealed a uniform distribution of Ag-TiO2nanocrystallites in pores and on mineral particle surfaces. The BET analysis showed remarkable surface and grain modification by sintering. Decreases in the BET-specific surface area were observed for the sintered ceramic nanocomposite, Ag-TiO2-kaolin (20.244 to 5.446 m2/g) and Ag-TiO2-diatomite (19.582 to 10.148 m2/g).

scholarly journals Activated Carbons from Thermoplastic Precursors and Their Energy Storage Applications

Nanomaterials ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 896 ◽  
Author(s):  
Hye-Min Lee ◽  
Kwan-Woo Kim ◽  
Young-Kwon Park ◽  
Kay-Hyeok An ◽  
Soo-Jin Park ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Specific Surface ◽  
Surface Area ◽  
Field Emission ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Cross Linking ◽  
Mesopore Volume

In this study, low-density polyethylene (LDPE)-derived activated carbons (PE-AC) were prepared as electrode materials for an electric double-layer capacitor (EDLC) by techniques of cross-linking, carbonization, and subsequent activation under various conditions. The surface morphologies and structural characteristics of the PE-AC were observed by field-emission scanning electron microscope, Cs-corrected field-emission transmission electron microscope, and X-ray diffraction analysis, respectively. The nitrogen adsorption isotherm-desorption characteristics were confirmed by Brunauer–Emmett–Teller, nonlocal density functional theory, and Barrett–Joyner–Halenda equations at 77 K. The results showed that the specific surface area and total pore volume of the activated samples increased with increasing the activation time. The specific surface area, the total pore volume, and mesopore volume of the PE-AC were found to be increased finally to 1600 m2/g, 0.86 cm3/g, and 0.3 cm3/g, respectively. The PE-AC also exhibited a high mesopore volume ratio of 35%. This mesopore-rich characteristic of the activated carbon from the LDPE is considered to be originated from the cross-linking density and crystallinity of precursor polymer. The high specific surface area and mesopore volume of the PE-AC led to their excellent performance as EDLC electrodes, including a specific capacitance of 112 F/g.

Sign in / Sign up

Export Citation Format

Share Document