scholarly journals Structure and Properties of TiO2/nanoTiO2 Bimodal Coatings Obtained by a Hybrid PVD/ALD Method on 316L Steel Substrate

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4369
Author(s):  
Marcin Staszuk ◽  
Daniel Pakuła ◽  
Łukasz Reimann ◽  
Anna Kloc-Ptaszna ◽  
Mirosława Pawlyta ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Electrochemical Properties ◽  
Surface Engineering ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
Atomic Layer ◽  
Scanning Transmission Electron Microscope ◽  
Structural Defects ◽  
Structure And Properties ◽  
316L Steel

This paper presents the synergy of the effect of two surface engineering technologies—magnetron sputtering (MS-PVD) and atomic layer deposition (ALD) on the structure and properties of 316L steel. Recent studies indicate that PVD coatings, despite their thickness of a few micrometers, have many discontinuities and structural defects, which may lead to pitting corrosion after time. Applying an ALD layer to a PVD coating seals its structure and contributes to extending the service life of the coating. Investigations of the structure and morphology of the produced layers were carried out using a scanning electron microscope (SEM) and atomic force microscope (AFM). In addition, the structure of the coatings was investigated on the cross-section using a scanning-transmission electron microscope S/TEM. The tribological properties of the materials studied were determined by the ball-on-disc method. The corrosion resistance of the tested materials was determined by the electrochemical potentiodynamic method by recording the polarization curves of the anodes. Additional information about the electrochemical properties of the tested samples, including the quality, their tightness, and their resistivity, was obtained by electrochemical impedance spectroscopy (EIS). In addition, the main mechanisms of corrosion and tribological wear were determined by SEM observations after corrosion tests and after tribological tests. The study showed that the fabrication of hybrid layers by MS-PVD and ALD techniques allows obtaining coatings with electrochemical properties superior to those of layers fabricated by only one method.

The study of the electrochemical properties of zinc-rich coating on the base of water sodium silicate

2019 ◽  
Vol 24 (4) ◽  
pp. 51-58
Author(s):  
Le Hong Quan ◽  
Nguyen Van Chi ◽  
Mai Van Minh ◽  
Nong Quoc Quang ◽  
Dong Van Kien
Keyword(s):  
Carbon Steel ◽  
Electrochemical Properties ◽  
Sodium Silicate ◽  
Cathodic Protection ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
Electrical Contact ◽  
Electrochemical Impedance Spectra ◽  
Pure Zinc ◽  
Electric Circuits

The study examines the electrochemical properties of a coating based on water sodium silicate and pure zinc dust (ZSC, working title - TTL-VN) using the Electrochemical Impedance Spectra (EIS) with AutoLAB PGSTAT204N. The system consists of three electrodes: Ag/AgCl (SCE) reference electrode in 3 M solution of KCl, auxiliary electrode Pt (8x8 mm) and working electrodes (carbon steel with surface treatment up to Sa 2.5) for determination of corrosion potential (Ecorr) and calculation of equivalent electric circuits used for explanation of impedance measurement results. It was shown that electrochemical method is effective for study of corrosion characteristics of ZSC on steel. We proposed an interpretation of the deterioration over time of the ability of zinc particles in paint to provide cathodic protection for carbon steel. The results show that the value of Ecorr is between -0,9 and -1,1 V / SCE for ten days of diving. This means that there is an electrical contact between the zinc particles, which provides good cathodic protection for the steel substrate and most of the zinc particles were involved in the osmosis process. The good characteristics of the TTL-VN coating during immersion in a 3,5% NaCl solution can also be explained by the preservation of corrosive zinc products in the coating, which allows the creation of random barrier properties.

scholarly journals Comparison of the Growth and Thermal Properties of Nonwoven Polymers after Atomic Layer Deposition and Vapor Phase Infiltration

Coatings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1028
Author(s):  
Laura Keskiväli ◽  
Pirjo Heikkilä ◽  
Eija Kenttä ◽  
Tommi Virtanen ◽  
Hille Rautkoski ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Electron Microscope ◽  
Atomic Layer Deposition ◽  
Atomic Layer ◽  
Scanning Transmission Electron Microscope ◽  
Scanning Calorimetry ◽  
Polymeric Surfaces ◽  
Transmission Electron ◽  
Layer Deposition ◽  
Scanning Transmission

The growth mechanism of Atomic Layer Deposition (ALD) on polymeric surfaces differs from growth on inorganic solid substrates, such as silicon wafer or glass. In this paper, we report the growth experiments of Al2O3 and ZnO on nonwoven poly-L-lactic acid (PLLA), polyethersulphone (PES) and cellulose acetate (CA) fibres. Material growth in both ALD and infiltration mode was studied. The structures were examined with a scanning electron microscope (SEM), scanning transmission electron microscope (STEM), attenuated total reflectance-fourier-transform infrared spectroscopy (ATR-FTIR) and 27Al nuclear magnetic resonance (NMR). Furthermore, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis were used to explore the effect of ALD deposition on the thermal properties of the CA polymer. According to the SEM, STEM and ATR-FTIR analysis, the growth of Al2O3 was more uniform than ZnO on each of the polymers studied. In addition, according to ATR-FTIR spectroscopy, the infiltration resulted in interactions between the polymers and the ALD precursors. Thermal analysis (TGA/DSC) revealed a slower depolymerization process and better thermal resistance upon heating both in ALD-coated and infiltrated fibres, more pronounced on the latter type of structures, as seen from smaller endothermic peaks on TA.

scholarly journals Structure and Surface Morphology Effect on the Cytotoxicity of [Al2O3/ZnO]n/316L SS Nanolaminates Growth by Atomic Layer Deposition (ALD)

Crystals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 620
Author(s):  
D. Osorio ◽  
J. Lopez ◽  
H. Tiznado ◽  
Mario H. Farias ◽  
M. A. Hernandez-Landaverde ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Atomic Layer Deposition ◽  
Biomedical Applications ◽  
316L Stainless Steel ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
Chinese Hamster ◽  
Atomic Layer ◽  
X Ray ◽  
Layer Deposition

Recently, different biomedical applications of aluminum oxide (Al2O3) and zinc oxide (ZnO) have been studied, and they have displayed good biocompatible behavior. For this reason, this study explores nanolaminates of [Al2O3/ZnO]n obtained by atomic layer deposition (ALD) on silicon (100) and 316L stainless steel substrates with different bilayer periods: n = 1, 2, 5, and 10. The intention is to correlate the structure, chemical bonds, morphology, and electrochemical properties of ZnO and Al2O3 single layers and [Al2O3/ZnO]n nanolaminates with their cytotoxic and biocompatibility behavior, to establish their viability for biomedical applications in implants based on the 316L SS substrate. These nanolaminates have been characterized by grazing incident X-ray diffraction (XRD), finding diffraction planes for wurtzite type structure from zincite. The chemical bonding and composition for both single layers were identified through X-ray photoelectron spectroscopy (XPS). The morphology and roughness were tested with atomic force microscopy (AFM), which showed a reduction in roughness and grain size with a bilayer period increase. The thickness of the samples was measured with scanning electron microscopy, and the results confirmed the value of ~210 nm for the nanolaminate samples. The electrochemical impedance spectroscopy analysis with Hank’s balanced salt solution (HBSS) evidenced an evolution of [Al2O3/ZnO]n/316L system corrosion resistance of around 95% in relation with the uncoated steel substrate as function of the increase in the bilayers number. To identify the biocompatibility behavior of these nanolaminate systems, the lactate dehydrogenase test was performed with Chinese hamster ovary (CHO) cells for a short system of life cell evaluation. This test shows the cytotoxicity of the multilayer compared to the single layers of Al2O3, ZnO, and 316L stainless steel. The lowest cytotoxicity was found in the single layers of ZnO, which leads to cell proliferation easier than Al2O3, obtaining better adhesion and anchoring to its surface.

Study of Structural Defects in CdZnTe Crystals by High Resolution Electron Microscopy

2011 ◽  
Vol 1341 ◽  
Author(s):  
A. Hossain ◽  
A. E. Bolotnikov ◽  
G. S. Camarda ◽  
Y. Cui ◽  
R. Gul ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
High Resolution ◽  
High Resolution Electron Microscopy ◽  
Scanning Transmission Electron Microscope ◽  
Structural Defects ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Scanning Transmission ◽  
Infrared Microscope

ABSTRACTWe investigated defects in CdZnTe crystals produced from various conditions and their impact on fabricated devices. In this study, we employed transmission and scanning transmission electron microscope (TEM and STEM), because defects at the nano-scale are not observed readily under an optical or infrared microscope, or by most other techniques. Our approach revealed several types of defects in the crystals, such as low-angle boundaries, dislocations and precipitates, which likely are major causes in degrading the electrical properties of CdZnTe devices, and eventually limiting their performance.

scholarly journals Self-healing and corrosion performance of polyurethane coating containing polyurethane microcapsules

2021 ◽  
Author(s):  
Hanieh Fathi Fathabadi ◽  
Mehdi Javidi
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Interfacial Polymerization ◽  
Electrochemical Impedance ◽  
Steel Substrate ◽  
The Self ◽  
Self Healing ◽  
Polyurethane Coating ◽  
Healing Efficiency ◽  
Scanning Electron

Abstract In this study, the self-healing behavior of the polyurethane coating containing polyurethane microcapsules was investigated. Microcapsules, with the average size of 99 µm and shell thickness of 11 µm, were successfully synthesized via the interfacial polymerization technique and were incorporated into the polyurethane coating matrix. The electrochemical impedance spectroscopy and scanning electron microscope were employed to investigate the healing performance and corrosion behavior of the coatings on the carbon steel substrate. The recorded results revealed that artificial scratches were successfully healed and the coating containing 20 wt% microcapsules exhibited the best healing performance (85% healing efficiency) among all the prepared coatings. The self-healing ability of the coatings were verified via scanning electron microscope. After 24 hours, the healing efficiency attained a reasonable value of 68% during exposure to test solution. It was found that corrosion resistance and coating adhesion were significantly improved by incorporating the microcapsules into the coating.

The High Resolution Scanning Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 316-317
Author(s):  
A. V. Crewe
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
High Vacuum ◽  
Scanning Transmission Electron Microscope ◽  
Ultra High Vacuum ◽  
Resolving Power ◽  
Imaging Characteristics ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
The Moment

The high resolution STEM is now a fact of life. I think that we have, in the last few years, demonstrated that this instrument is capable of the same resolving power as a CEM but is sufficiently different in its imaging characteristics to offer some real advantages.It seems possible to prove in a quite general way that only a field emission source can give adequate intensity for the highest resolution^ and at the moment this means operating at ultra high vacuum levels. Our experience, however, is that neither the source nor the vacuum are difficult to manage and indeed are simpler than many other systems and substantially trouble-free.

Development of 200 kV Scanning-Transmission Electron Microscope

1974 ◽  
Vol 32 ◽  
pp. 410-411
Author(s):  
H. Koike ◽  
S. Sakurai ◽  
K. Ueno ◽  
M. Watanabe
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Scanning Transmission Electron Microscope ◽  
The Other ◽  
Morphological Observation ◽  
Magnetic Domains ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Backscattered Electron ◽  
Increasing Demand

In recent years, there has been increasing demand for higher voltage SEMs, in the field of surface observation, especially that of magnetic domains, dislocations, and electron channeling patterns by backscattered electron microscopy. On the other hand, the resolution of the CTEM has now reached 1 ∼ 2Å, and several reports have recently been made on the observation of atom images, indicating that the ultimate goal of morphological observation has beem nearly achieved.

To What Extent are Inelastically Scattered Electrons Useful in the Stem?

1973 ◽  
Vol 31 ◽  
pp. 286-287 ◽  
Author(s):  
H. Rose
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Electron Correlation ◽  
Quantum Noise ◽  
Collection Efficiency ◽  
Scanning Transmission Electron Microscope ◽  
Electron Cloud ◽  
Scanning Time ◽  
Transmission Electron ◽  
Scanning Transmission

The scanning transmission electron microscope offers the possibility of utilizing inelastically scattered electrons. Use of these electrons in addition to the elastically scattered electrons should reduce the scanning time (dose) Which is necessary to keep the quantum noise below a certain level. Hence it should lower the radiation damage. For high resolution, Where the collection efficiency of elastically scattered electrons is small, the use of Inelastically scattered electrons should become more and more favorable because they can all be detected by means of a spectrometer. Unfortunately, the Inelastic scattering Is a non-localized interaction due to the electron-electron correlation, occurring predominantly at the circumference of the atomic electron cloud.

The direct determination of magnetic domain wall profiles using a split detector STEM

1978 ◽  
Vol 36 (1) ◽  
pp. 466-467
Author(s):  
J.N. Chapman ◽  
P.E. Batson ◽  
E.M. Waddell ◽  
R.P. Ferrier
Keyword(s):  
Electron Microscope ◽  
Domain Wall ◽  
Transmission Electron Microscope ◽  
Domain Walls ◽  
Photographic Plate ◽  
Magnetic Domain ◽  
Direct Determination ◽  
Quantitative Information ◽  
Scanning Transmission Electron Microscope ◽  
Transmission Electron

By far the most commonly used mode of Lorentz microscopy in the examination of ferromagnetic thin films is the Fresnel or defocus mode. Use of this mode in the conventional transmission electron microscope (CTEM) is straightforward and immediately reveals the existence of all domain walls present. However, if such quantitative information as the domain wall profile is required, the technique suffers from several disadvantages. These include the inability to directly observe fine image detail on the viewing screen because of the stringent illumination coherence requirements, the difficulty of accurately translating part of a photographic plate into quantitative electron intensity data, and, perhaps most severe, the difficulty of interpreting this data. One solution to the first-named problem is to use a CTEM equipped with a field emission gun (FEG) (Inoue, Harada and Yamamoto 1977) whilst a second is to use the equivalent mode of image formation in a scanning transmission electron microscope (STEM) (Chapman, Batson, Waddell, Ferrier and Craven 1977), a technique which largely overcomes the second-named problem as well.

A General Method for Spectrometer Design in the Scoff Approximation

1976 ◽  
Vol 34 ◽  
pp. 538-539
Author(s):  
J. R. Fields
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Energy Analysis ◽  
Incident Beam ◽  
Scanning Transmission Electron Microscope ◽  
Chemical Identification ◽  
Scanning Transmission Electron ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
General Method

The energy analysis of electrons scattered by a specimen in a scanning transmission electron microscope can improve contrast as well as aid in chemical identification. In so far as energy analysis is useful, one would like to be able to design a spectrometer which is tailored to his particular needs. In our own case, we require a spectrometer which will accept a parallel incident beam and which will focus the electrons in both the median and perpendicular planes. In addition, since we intend to follow the spectrometer by a detector array rather than a single energy selecting slit, we need as great a dispersion as possible. Therefore, we would like to follow our spectrometer by a magnifying lens. Consequently, the line along which electrons of varying energy are dispersed must be normal to the direction of the central ray at the spectrometer exit.

Sign in / Sign up

Export Citation Format

Share Document