scholarly journals Durability Performance Indices for Cement-Based Mortars

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2758
Author(s):  
Rebeca Visairo-Méndez ◽  
Andrés A. Torres-Acosta ◽  
Roberto Alvarado-Cárdenas
Keyword(s):  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Void Content ◽  
Capillary Absorption ◽  
Chloride Permeability ◽  
Repair Mortar ◽  
Durability Design ◽  
Repair Materials ◽  
Durability Performance

Corrosion-induced damaged structures are generally repaired using locally available materials. Nevertheless, determining the durability of the repair materials to be used is necessary to forecast its service life after being placed on the damaged structure. In previous investigations, the most commonly used durability indices are saturated electrical resistivity (ρS), ultrasonic pulse velocity (UPV), total void content (TVC), water capillary absorption (WCA), rapid chloride permeability (RCP), and compressive strength (fc). Four repair mortar types were evaluated. For each mortar type, 5 × 5 cm2 cubes, 5 × 10 cm2 (small) cylinders, and 10 × 20 cm2 (large) cylinders were made from each mortar evaluated. On the basis of the present results, the durability design of mortars should consider not only the mechanical strength, but also the durability index values to define its durability performance. According to the empirical correlations obtained between all durability indices, ρS vs. RCP, TVC vs. WCA, and RCP vs. WCA were the ones with higher correlation coefficient. These correlations could be used for mortar mixture durability forecasting.

Non-Destructive Tests as Durability Indicators in Cement Mortars with Pozzolanic Substitutions

2017 ◽  
Vol 902 ◽  
pp. 9-13
Author(s):  
Rosalía Ruiz Ruiz ◽  
Elia Mercedes Alonso Guzmán ◽  
Wilfrido Martínez Molina ◽  
Hugo Luis Chávez García ◽  
Judith Alejandra Velázquez Perez
Keyword(s):  
Mechanical Characteristics ◽  
Ultrasonic Pulse Velocity ◽  
Good Alternative ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Cement Industry ◽  
Capillary Absorption ◽  
Pozzolanic Material ◽  
Cement Mortars ◽  
Non Destructive

Cement industry is responsible of 5-7% of CO2 emissions to the atmosphere. This is preoccupant because this is one of the greenhouse effect gases which cause global warming. Pozzolanic material incorporation in cement mortars elaboration represents a good alternative to partially substitute cement, since its chemical composition could contribute to improvement of its durability and mechanical characteristics. In this research, mortars with pozzolanic substitutions are evaluated through non-destructive tests as: capillary absorption, electrical resistivity, and ultrasonic pulse velocity to the age of 1000 days. The results suggested that the incorporation of pozzolanic material as partial substitutes of Portland cement increases the mortars properties mainly in substitutions of CBC 20%, PN 10, and 30%.

scholarly journals Transport Properties and Resistance Improvement of Ultra-High Performance Concrete (UHPC) after Exposure to Elevated Temperatures

Buildings ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 416
Author(s):  
Yunfeng Qian ◽  
Dingyi Yang ◽  
Yanghao Xia ◽  
Han Gao ◽  
Zhiming Ma
Keyword(s):  
Compressive Strength ◽  
Transport Properties ◽  
High Temperatures ◽  
High Performance ◽  
High Performance Concrete ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Capillary Absorption ◽  
Self Healing

Ultra-high performance concrete (UHPC) has a high self-healing capacity and is prone to bursting after exposure to high temperatures due to its characteristics. This work evaluates the damage and improvement of UHPC with coarse aggregates through mechanical properties (compressive strength and ultrasonic pulse velocity), transport properties (water absorption and a chloride diffusion test), and micro-properties such as X-ray diffraction (XRD), Mercury intrusion porosimetry (MIP), and Scanning electronic microscopy (SEM). The result demonstrates that polypropylene (PP) fibers are more suitable for high temperature tests than polyacrylonitrile (PAN) fibers. The result shows that 400 °C is the critical temperature point. With the increase in temperature, the hydration becomes significant, and the internal material phase changes accordingly. Although the total pore volume increased, the percentage of various types of pores was optimized within 400 °C. The mass loss gradually increased and the ultrasonic pulse velocity gradually decreased. While the compressive strength first increased and then decreased, and the increase occurred within 25–400 °C. As for the transport properties, the chloride migration coefficient and capillary absorption coefficient both increased dramatically due to the higher sensitivity to temperature changes. The results of the property improvement test showed that at temperatures above 800 °C, the compressive strength recovered by more than 65% and the ultrasonic pulse velocity recovered by more than 75%. In terms of transport properties, compared to the results before self-healing, the chloride migration coefficient decreased by up to 59%, compared with 89% for the capillary absorption coefficient, after self-healing at 800 °C. With respect to the enhancement effect after exposure to high temperatures, the environment of a 5% Na2SO4 solution was not as good as the clean water environment. The corresponding changes in microstructure during the high temperatures and the self-healing process can explain the change in the pattern of macroscopic properties more precisely.

scholarly journals Use of Waste Glass as A Replacement for Raw Materials in Mortars with a Lower Environmental Impact

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1974 ◽  
Author(s):  
Viviana Letelier ◽  
Bastián I. Henríquez-Jara ◽  
Miguel Manosalva ◽  
Camila Parodi ◽  
José Marcos Ortega
Keyword(s):  
Glass Powder ◽  
Raw Materials ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Environmental Benefits ◽  
Dry Density ◽  
Capillary Absorption ◽  
Powder Size ◽  
Glass Waste

Glass waste used in mortars or concretes behaves similar to cement, with resulting environmental benefits. In this light, the behavior of glass powder of various particle sizes has been analyzed as a cement replacement in mortars, in an attempt to minimize the loss of strength and durability, and maximize the amount of materials replaced. The dry density, water accessible porosity, water absorption by immersion, capillary absorption coefficient, ultrasonic pulse velocity and both compressive and flexural strengths were studied in the mortars. Furthermore, a statistical analysis of the obtained results and a greenhouse gases assessment were also performed. In view of the results obtained, glass powder of 38 microns allows up to 30% of the cement to be replaced, due to the filler effect combined with its pozzolanic activity. Moreover, it has been observed that glass powder size is one of the factors with the greatest influence among the properties of porosity, absorption and capillarity. On the other hand, in the mechanical properties, this factor does not contribute significantly more than the amount of glass powder. Finally, the greenhouse gasses analysis shows that the incorporation of glass powder reduces the CO2 emissions associated with mortar up to 29.47%.

Self-Healing Mortar

2019 ◽  
pp. 135-148
Keyword(s):  
Epoxy Resin ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Experimental Program ◽  
Self Healing ◽  
Repair Materials ◽  
Healing Agent ◽  
The Cost ◽  
Initial Reading

The cost of repairing cracked concrete is expensive as it requires special repair materials and skilled labour. Thus, the developments of new materials, like self-healing materials, are highly needed to repair cracks automatically and to restore or even increase concretes' strength to prolong its service life. The aim of this chapter was to investigate the performance of epoxy resin without hardener as a self-healing agent in mortar. A detailed introduction of self-healing mortar is given followed by a problem statement. The epoxy resin as a self-healing material is also explained briefly. Self-healing concept is also discussed in detail followed by the experimental program. Results revealed that the epoxy resin without hardener as a healing agent performed effectively as the compressive strength and ultrasonic pulse velocity of 365 days old cracked mortar samples regained the initial reading with prolonged curing time.

Characterization of Mortar with Mineral Additives

2013 ◽  
Vol 1612 ◽  
Author(s):  
M. R. Mejía Durán ◽  
A. A. Torres Acosta ◽  
M.G. Arroyo Contreras ◽  
M. Rendón Belmonte
Keyword(s):  
Electrical Resistivity ◽  
Previous Investigation ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Void Content ◽  
System Efficiency ◽  
Concrete Pile ◽  
Mineral Additives

ABSTRACTIt has been an increase on the number of concrete structures with corrosion induced damage in Mexico in recent years. It is also well known that cathodic protection (CP) is the only method that stops corrosion in an efficient way. Since the 1990’s Florida and other USA states have been installing in concrete pile substructures, in bridges and piers, a three part hybrid galvanic CP system. This hybrid galvanic CP system includes a thermal sprayed part (located at the aerial zone of the pile), a zinc mesh encapsulated in mortar and inside a glass fiber jacket (located at the change in ties zone), and a submerged zinc bulk anode (in the submerged zone). From a previous investigation performed by the present authors, it has been found that the mortar inside the fiberglass form may decrease the mesh anode activation and thus decrease the CP system efficiency. Therefore, this investigation includes an evaluation of different additions placed in mortar to increase its electrical and ionic conductivity to increase the efficiency of the entire hybrid system. Additions include carbon, zinc and alumina powders, and this investigation presents preliminary experimental results obtained from the tested mortars (i.e. mortar physical characterization: electrical resistivity, ultrasonic pulse velocity, and total void content).

scholarly journals Strength and Durability Assessment of Portland Cement Mortars Formulated from Hydrogen-Rich Water

2017 ◽  
Vol 2017 ◽  
pp. 1-10
Author(s):  
Byung Wan Jo ◽  
Muhammad Ali Sikandar ◽  
Sumit Chakraborty ◽  
Zafar Baloch
Keyword(s):  
Portland Cement ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Capillary Absorption ◽  
X Ray Diffraction ◽  
Degree Of Hydration ◽  
Cement Mortars ◽  
Durability Assessment ◽  
Strength And Durability

We investigated the effects of hydrogen-rich water (HRW) on the strength and durability of Portland cement mortars. We comparatively assessed the performances of HRW-based mortars (HWMs) with respect to cement mortars fabricated from control water (CWM). The results indicate that the use of HRW significantly improves the compressive, flexural, and splitting tensile strength of mortars at both the early and later ages of curing. Durability was assessed in terms of capillary absorption, ultrasonic pulse velocity (UPV), dynamic elastic modulus (DEM), and electrical resistivity (ER). We attribute the generally improved mechanical and durability properties of HWMs to the formation of more cement hydrates with fewer voids in the hydrogen-rich environment. Based on X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM) analyses, we deduce that the use of HRW in Portland cement mortars produces a more compact, dense, and durable microstructure with fewer voids due to a higher degree of hydration.

scholarly journals Performance of Mortars with Commercially-Available Reactive Magnesium Oxide as Alternative Binder

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 938 ◽  
Author(s):  
Miguel Bravo ◽  
Javier A. Forero ◽  
José Nobre ◽  
Jorge de Brito ◽  
Luís Evangelista
Keyword(s):  
Compressive Strength ◽  
Dynamic Modulus ◽  
Mechanical Performance ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
The Other ◽  
Strength Tests ◽  
Durability Performance ◽  
Different Levels

This paper intends to analyze the performance of mortars with reactive MgO, as a sustainable alternative to cement. Six different MgOs from Australia, Canada, and Spain were used in the production of mortars as partial substitutes for cement, namely 5%, 10%, 15%, 20%, and 25% (by weight). MgOs with different levels of reactivity were used to analyze its influence on the performance of MgO mortars. In order to evaluate the mechanical performance of these mortars, compressive strength, flexural strength, dynamic modulus of elasticity, and ultrasonic pulse velocity tests were performed. Compressive strength tests showed that the use of 25% reactive MgO can cause a decrease of this property of between 28% and 49%. The use of reactive MgO affected the other mechanical properties less. This paper also intends to analyze the durability performance of mortars with reactive MgO. To that effect, water absorption by capillarity was assessed. In this research, the effect of using MgO on the shrinkage was also analyzed. It was found that shrinkage may decrease by more than a half in some cases.

PENGKAJIAN KEKUATAN BETON STRUKTUR JEMBATAN PASCA KEBAKARAN

2013 ◽  
Vol 12 (3) ◽  
Author(s):  
Sudarmadi Sudarmadi
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Strength Assessment ◽  
Concrete Testing

In this paper a case study about concrete strength assessment of bridge structure experiencing fire is discussed. Assessment methods include activities of visual inspection, concrete testing by Hammer Test, Ultrasonic Pulse Velocity Test, and Core Test. Then, test results are compared with the requirement of RSNI T-12-2004. Test results show that surface concrete at the location of fire deteriorates so that its quality is decreased into the category of Very Poor with ultrasonic pulse velocity ranges between 1,14 – 1,74 km/s. From test results also it can be known that concrete compressive strength of inner part of bridge pier ranges about 267 – 274 kg/cm2 and concrete compressive strength of beam and plate experiencing fire directly is about 173 kg/cm2 and 159 kg/cm2. It can be concluded that surface concrete strength at the location of fire does not meet the requirement of RSNI T-12-2004. So, repair on surface concrete of pier, beam, and plate at the location of fire is required.

Sign in / Sign up

Export Citation Format

Share Document