scholarly journals Response Surface Methods Used for Optimization of Abrasive Waterjet Machining of the Stainless Steel X2 CrNiMo 17-12-2

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2475
Author(s):  
Andrea Deaconescu ◽  
Tudor Deaconescu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Response Surface ◽  
Input Parameter ◽  
Traverse Speed ◽  
Machining Process ◽  
Abrasive Waterjet ◽  
Machined Surface ◽  
Abrasive Waterjet Machining ◽  
Waterjet Machining

Abrasive waterjet machining (AWJM) has a particularly high potential for the machining of stainless steels. One of the main optimization objectives of the machining of X2 CrNiMo 17-12-2 stainless steel is obtaining a minimal surface roughness. This entails selecting an optimum configuration of the main influencing factors of the machining process. Optimization of the machining system was achieved by intervening on four selected input quantities (traverse speed, waterjet pressure, stand-off distance, and grit size), with three set points considered for each. The effects of modifying the set-points of each input parameter on the surface roughness were studied. By means of response surface methodology (RSM) the combination of factor set points was determined that ensures a minimum roughness of the machined surface. The main benefit of RSM is the reduced time needed for experimenting.

Multiresponse Analysis in Abrasive Waterjet Machining Process on AA 6351

2014 ◽  
Vol 4 (4) ◽  
pp. 38-48 ◽  
Author(s):  
Naresh Babu Munuswamy ◽  
M. Nambi Krishnan
Keyword(s):  
Surface Roughness ◽  
Optimal Parameter ◽  
Water Pressure ◽  
Traverse Speed ◽  
Machining Process ◽  
Abrasive Waterjet ◽  
Abrasive Waterjet Machining ◽  
Waterjet Machining ◽  
Kerf Angle ◽  
Grey Relational

This study investigates optimal parameter setting in abrasive waterjet machining (AWJM) on aluminium alloy AA 6351, using taguchi based Grey Relational Analysis (GRA) is been reported. The water pressure, traverse speed and stand-off-distance were chosen as the process parameters in this study. An L9 orthogonal matrix array is used for the experimental plan. The performance characteristics which include surface roughness (Ra) and kerf angle (KA) are considered. The results indicate that surface roughness and kerf angle decreases, with increase in water pressure and decrease in traverse speed. Analysis of variance (ANOVA) illustrates that traverse speed is the major parameter (89.7%) for reducing surface roughness and kerf angle, followed by water pressure (5.85%) and standoff distance (2%) respectively. The confirmation results reveal that surface roughness reduced by 16% and kerf angle reduced by 47%. Furthermore, the surfaces were examined under scanning electron microscope (SEM) and atomic force microscope (AFM) for a detailed study

EXPERIMENTAL STUDY OF SURFACE ROUGHNESS AND TAPER ANGLE IN ABRASIVE WATER JET MACHINING OF 7075 ALUMINUM COMPOSITE USING RESPONSE SURFACE METHODOLOGY

2019 ◽  
Vol 27 (03) ◽  
pp. 1950112 ◽  
Author(s):  
A. SHANMUGAM ◽  
K. KRISHNAMURTHY ◽  
T. MOHANRAJ
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Water Pressure ◽  
Traverse Speed ◽  
Standoff Distance ◽  
Abrasive Waterjet ◽  
Machined Surface ◽  
Taper Angle

Surface roughness and taper angle of an abrasive waterjet machined surface of 7075 Aluminum metal matrix composite were deliberately studied. Response surface methodology design of experiments and analysis of variance were used to design the experiments and to identify the effect of process parameters on surface roughness and taper angle. The jet traverse speed and jet pressure were the most significant process parameters which influence the surface roughness and taper angle, respectively. Increasing the pressure and jet traverse speed results in increasing the surface roughness and taper angle. At the same time, decreasing the standoff distance and jet traverse speed possibly enhances both the responses. The optimal process parameters of 1[Formula: see text]mm as standoff distance, 192[Formula: see text]MPa as water pressure and 30[Formula: see text]mm[Formula: see text]min[Formula: see text] as jet traverse speed were identified to obtain the minimum value of surface roughness and taper angle. Based on the optimal parameters, the confirmation test was conducted. The mathematical equation was obtained from the experimental data using regression analysis; it was observed that the error was less than 5% of the experimentally measured values.

EXPERIMENTAL INVESTIGATION ON ABRASIVE WATERJET MACHINING OF FIBRE VINYL ESTER COMPOSITE

2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Puneet Kumar ◽  
Bhavik Tank ◽  
Ravi Kant
Keyword(s):  
Surface Roughness ◽  
Vinyl Ester ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Machining Processes ◽  
Significant Parameter ◽  
Abrasive Water Jet Machining ◽  
Abrasive Waterjet Machining ◽  
Waterjet Machining

Abrasive water jet machining (AWJM) is one of the most developed non-traditional machining processes. It is generally used to cut difficult to cut materials like composites. The present study is focused on machining of carbon fiber vinyl ester composite with AWJM. The effect of process parameters namely water pressure, standoff distance and traverse speed on surface roughness and kerf tapper is studied. Design of experiment is done by using Taguchi L16 orthogonal array. It is observed that water pressure is the most significant parameter followed by traverse speed. It is found that with the increase in water pressure and decrease in traverse speed of AWJM, surface roughness and kerf tapper of machined samples decreases.

Machinability Study of Hybrid FRP Composite Using Abrasive Waterjet Trimming Technology

2017 ◽  
Vol 740 ◽  
pp. 118-124 ◽  
Author(s):  
M.M.W. Irina ◽  
Azwan Iskandar Azmi ◽  
Chang Chuan Lee
Keyword(s):  
Surface Roughness ◽  
Thermal Sensitivity ◽  
Fiber Reinforcement ◽  
Machining Process ◽  
Abrasive Waterjet ◽  
Hydraulic Pressure ◽  
Abrasive Waterjet Machining ◽  
Frp Composite ◽  
Waterjet Machining ◽  
Conventional Machining

Machining of fiber reinforcement polymer (FRP) composite without any defect is extremely challenging when using conventional processes. This mainly due to its inherent anisotropic, heterogeneous, thermal sensitivity, and highly abrasive of nature of fiber reinforcement. Therefore, a kind of non-conventional machining process namely abrasive waterjet machining (AWJM) was endeavoured as it has been reported to be able to machine or cut almost any material included composites. In fact, previous research only provides partially desired parameters on machining these materials and mainly focuses on plain FRP composite. Therefore, this research attempted to evaluate the significant AWJM process parameters comprehensively on the main machinability output on the hybrid FRP composite. 2k factorial design and statistical analysis of variance (ANOVA) were applied to determine the performance of trimming process regarding surface roughness and delamination (entrance and exit). Experimental results revealed that the surface roughness was affected by the stand-off distance, abrasive flow rate, traverse rate rather than hydraulic pressure. Similar findings as to that of surface roughness were also observed for the top and bottom delamination damage.

scholarly journals Impacts of Traverse Speed and Material Thickness on Abrasive Waterjet Contour Cutting of Austenitic Stainless Steel AISI 304L

2021 ◽  
Vol 11 (11) ◽  
pp. 4925
Author(s):  
Jennifer Milaor Llanto ◽  
Majid Tolouei-Rad ◽  
Ana Vafadar ◽  
Muhammad Aamir
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Taper Angle ◽  
Material Thickness ◽  
Abrasive Waterjet Machining ◽  
Kerf Taper ◽  
Waterjet Machining

Abrasive water jet machining is a proficient alternative for cutting difficult-to-machine materials with complex geometries, such as austenitic stainless steel 304L (AISI304L). However, due to differences in machining responses for varied material conditions, the abrasive waterjet machining experiences challenges including kerf geometric inaccuracy and low material removal rate. In this study, an abrasive waterjet machining is employed to perform contour cutting of different profiles to investigate the impacts of traverse speed and material thickness in achieving lower kerf taper angle and higher material removal rate. Based on experimental investigation, a trend of decreasing the level of traverse speed and material thickness that results in minimum kerf taper angle values of 0.825° for machining curvature profile and 0.916° for line profiles has been observed. In addition, higher traverse speed and material thickness achieved higher material removal rate in cutting different curvature radii and lengths in line profiles with obtained values of 769.50 mm3/min and 751.5 mm3/min, accordingly. The analysis of variance revealed that material thickness had a significant impact on kerf taper angle and material removal rate, contributing within the range of 69–91% and 62–69%, respectively. In contrast, traverse speed was the least factor measuring within the range of 5–18% for kerf taper angle and 27–36% for material removal rate.

Abrasive Waterjet Cutting of Aluminum Alloys: Workpiece Surface Roughness

2013 ◽  
Vol 404 ◽  
pp. 3-9 ◽  
Author(s):  
Nihat Tosun ◽  
Ihsan Dagtekin ◽  
Latif Ozler ◽  
Ahmet Deniz
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Aluminum Alloys ◽  
Abrasive Waterjet ◽  
Traditional Methods ◽  
Workpiece Surface ◽  
Abrasive Waterjet Machining ◽  
Waterjet Machining ◽  
Area Of Application ◽  
Better Than

Abrasive waterjet machining is one of the non-traditional methods of the recent years which found itself a wide area of application in the industry for machining of different materials. In this paper, the surface roughness of 6061-T6 and 7075-T6 aluminum alloys are being cut with abrasive waterjet is examined experimentally. The experiments were conducted with different waterjet pressures and traverse speeds. It has been found that the surface roughness obtained by cutting material with high mechanical properties is better than that of obtained by cutting material with inferior mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document