scholarly journals Morphology, Mechanical Properties and Shape Memory Effects of Polyamide12/Polyolefin Elastomer Blends Compatibilized by Glycidylisobutyl POSS

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 27
Author(s):  
Dong-Hun Lee ◽  
Young-Wook Chang ◽  
Keon-Soo Jang
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Tensile Modulus ◽  
Domain Size ◽  
Mechanical Analysis ◽  
Sem Analysis ◽  
Melt Mixing ◽  
Polyolefin Elastomer ◽  
Shape Memory Effects ◽  
Izod Impact

Small amounts of glycidylisobutyl polyhedral oligomericsilsesquioxane (G-POSS) (up to 10 phr) were added into a immiscible polyamide12 (PA12)/polyolefin elastomer (POE) blend (70 wt%/30 wt%) by simple melt mixing. The effects of the G-POSS on phase morphology and mechanical properties were investigated by FE-SEM, tensile testing, Izod impact test and dynamic mechanical analysis. FE-SEM analysis revealed that domain size of the dispersed POE phase in matrix PA12 is decreased significantly by adding the G-POSS, indicating a compatibilization effect of the G-POSS for the immiscible PA12/POE blend. The PA12/POE blend compatibilized with POSS showed simultaneous enhancement in mechanical properties including tensile modulus, strength and toughness. Further, thermally triggered shape memory effect was observed in this compatibilized blend.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

scholarly journals Influence of Treated Distillate Aromatic Extract (TDAE) Content and Addition Time on Rubber-Filler Interactions in Silica Filled SBR/BR Blends

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 698
Author(s):  
Selin Sökmen ◽  
Katja Oßwald ◽  
Katrin Reincke ◽  
Sybill Ilisch
Keyword(s):  
Mechanical Properties ◽  
Oil Content ◽  
Tensile Modulus ◽  
Mechanical Analysis ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Binary Blends ◽  
Rubber Layer ◽  
Processing Aids ◽  
Rubber Filler

High compatibility and good rubber–filler interactions are required in order to obtain high quality products. Rubber–filler and filler–filler interactions can be influenced by various material factors, such as the presence of processing aids. Although different processing aids, especially the plasticizers, and their effects on compatibility have been investigated in the literature, their influence on rubber–filler interactions in highly active filler reinforced mixtures is not explicit and has not been investigated in depth. For this purpose, the influence of treated distillate aromatic extract (TDAE) oil content and its addition time on interactions between silica and rubber chains were investigated in this study. Rubber–filler and filler–filler interactions of uncured and cured silica-filled SBR/BR blends were characterized by using rubber layer L concept and dynamic mechanical analysis, whereas mechanical properties were studied by tensile test and Shore A hardness. Five parts per hundred rubber (phr) TDAE addition at 0, 1.5, and 3 min of mixing were characterized to investigate the influence of TDAE addition time on rubber–filler interactions. It was observed that addition time of TDAE can influence the development of bounded rubber structure and the interfacial interactions, especially at short time of mixing, less than 5 min. Oil addition with silica at 1.5 min of mixing resulted in fast rubber layer development and a small reduction in storage shear modulus of uncured blends. The influence of oil content on rubber–filler and filler–filler interactions were investigated for the binary blends without oil, with 5 and 20 phr TDAE content. The addition of 5 phr oil resulted in a slight increase in rubber layer and 0.05 MPa reduction in Payne effect of uncured blends. The storage tensile modulus of vulcanizates at small strains decreased from 13.97 to 8.28 MPa after oil addition. Twenty parts per hundred rubber (phr) oil addition to binary blends caused rubber layer L to decrease from 0.45 to 0.42. The storage tensile modulus of the vulcanizates and its reduction with higher amplitudes were incontrovertibly high among the vulcanizates with lower oil content, which were 13.57 and 4.49 MPa, respectively. When any consequential change in mechanical properties of styrene–butadiene rubber (SBR)/butadiene rubber (BR) blends could not be observed at different TDAE addition time, increasing amount of oil in blends enhanced elongation at break, and decreased Shore A hardness and tensile strength.

scholarly journals Study of the Preparation and Properties of TPS/PBSA/PLA Biodegradable Composites

2021 ◽  
Vol 5 (2) ◽  
pp. 48
Author(s):  
Yuxuan Wang ◽  
Yuke Zhong ◽  
Qifeng Shi ◽  
Sen Guo
Keyword(s):  
Mechanical Properties ◽  
Heat Resistance ◽  
Thermoplastic Starch ◽  
Sem Analysis ◽  
Infrared Spectrometry ◽  
Fourier Transform Infrared Spectrometry ◽  
Melt Mixing ◽  
Two Phase ◽  
Biodegradable Composites ◽  
Phase Compatibility

Thermoplastic starch/butyl glycol ester copolymer/polylactic acid (TPS/PBSA/PLA) biodegradable composites were prepared by melt-mixing. The structure, microstructure, mechanical properties and heat resistance of the TPS/PBSA/PLA composites were studied by Fourier-transform infrared spectrometry (FTIR), scanning electron microscopy (SEM), tensile test and thermogravimetry tests, respectively. The results showed that PBSA or PLA could bind to TPS by hydrogen bonding. SEM analysis showed that the composite represents an excellent dispersion and satisfied two-phase compatibility when the PLA, TPS and PBSA blended by a mass ration of 10, 30, and 60. The mechanical properties and the heat resistance of TPS/PBSA/PLA composite were improved by adding PLA with content less than 10%, according to the testing results.

scholarly journals Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1954
Author(s):  
Yang Liu ◽  
Xun Zhang ◽  
Quanxin Gao ◽  
Hongliang Huang ◽  
Yongli Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Maleic Anhydride ◽  
Ag Nanoparticles ◽  
Decomposition Temperature ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Maximum Value ◽  
Polyolefin Elastomer ◽  
Local Defects

In the present study, silver (Ag) nanoparticles and maleic anhydride-grafted polyolefin elastomer (MAH-g-POE) were used as enhancement additives to improve the performance of the polyoxymethylene (POM) homopolymer. Specifically, the POM/Ag/MAH-g-POE ternary nanocomposites with varying Ag nanoparticles and MAH-g-POE contents were prepared by a melt mixing method. The effects of the additives on the microstructure, thermal stability, crystallization behavior, mechanical properties, and dynamic mechanical thermal properties of the ternary nanocomposites were studied. It was found that the MAH-g-POE played a role in the bridging of the Ag nanoparticles and POM matrix and improved the interfacial adhesion between the Ag nanoparticles and POM matrix, owing to the good compatibility between Ag/MAH-g-POE and the POM matrix. Moreover, it was found that the combined addition of Ag nanoparticles and MAH-g-POE significantly enhanced the thermal stability, crystallization properties, and mechanical properties of the POM/Ag/MAH-g-POE ternary nanocomposites. When the Ag/MAH-g-POE content was 1 wt.%, the tensile strength reached the maximum value of 54.78 MPa. In addition, when the Ag/MAH-g-POE content increased to 15wt.%, the elongation at break reached the maximum value of 64.02%. However, when the Ag/MAH-g-POE content further increased to 20 wt.%, the elongation at break decreased again, which could be attributed to the aggregation of excessive Ag nanoparticles forming local defects in the POM/Ag/MAH-g-POE ternary nanocomposites. Furthermore, when the Ag/MAH-g-POE content was 20 wt.%, the maximum decomposition temperature of POM/Ag/MAH-g-POE ternary nanocomposites was 398.22 °C, which was 71.39 °C higher than that of pure POM. However, compared with POM, the storage modulus of POM/Ag/MAH-g-POE ternary nanocomposites decreased with the Ag/MAH-g-POE content, because the MAH-g-POE elastomer could reduce the rigidity of POM.

A strengthening approach for damping property and shape memory property of acrylic rubber/polylactide blends

2018 ◽  
Vol 51 (7-8) ◽  
pp. 626-643
Author(s):  
Chengliang Li ◽  
Xingxing Ji ◽  
Yang Lyu ◽  
Xinyan Shi
Keyword(s):  
Shape Memory ◽  
Loss Factor ◽  
Phenol Formaldehyde ◽  
Mechanical Analysis ◽  
Damping Properties ◽  
Shape Memory Property ◽  
Memory Property ◽  
Damping Material ◽  
Shape Memory Properties ◽  
Shape Memory Effects

In this work, a damping material was successfully prepared by blending acrylic rubber (ACM) and polylactide (PLA) with sulfur and soap salt as the curing agents. A phenol-formaldehyde (PF) resin was used as a modifier. The effects of PF on the mechanical properties, damping properties, compatibility and shape memory properties of the blends were studied. The compatibility and damping properties were characterized by dynamic mechanical analysis, Fourier transform infrared spectroscope and microstructure analysis. The shape memory properties were examined by thermal mechanical analyser. The results revealed that the tensile strength of the blends was decreased and the toughness was increased with the increase of PF loadings. The introduction of PF improved the compatibility between PLA and ACM, which was deduced from the fact that the glass transition temperature of ACM was increased and the two loss factor peaks became closer. It was also found that the loss factor peak became higher and the effective damping temperature range became wider due to the formation of hydrogen bonding, implying that the damping properties of ACM/PLA blends were significantly improved. The ACM/PLA blends exhibited good dual-shape memory effect and its shape recovery ratio was increased by introduction of PF and raising the trigger temperature. The blends also exhibited good triple-shape memory property, which was dramatically improved by the introduction of PF. The mechanisms for the enhanced shape memory effects were then analysed.

Physico Chemical Characterization of Nanofibrous Poly(Ε-Caprolactone) Electrospun Templates for Cell Adhesion

MRS Advances ◽  
2017 ◽  
Vol 2 (49) ◽  
pp. 2689-2694
Author(s):  
Karla A. Gaspar-Ovalle ◽  
Juan V. Cauich-Rodriguez ◽  
Armando Encinas
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Cell Adhesion ◽  
Tensile Modulus ◽  
Chemical Characterization ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Physico Chemical ◽  
Static Water

ABSTRACTNanofibrous mats of poly ε-caprolactone (PCL) were fabricated by electrospinning. The nanofiber structures were investigated and characterized by scanning electron microscope, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, static water-contact-angle analysis and mechanical properties. The results showed that the nanofibrous PCL is an ideal biopolymer for cell adhesion, owing to its biocompatibility, biodegradability, structural stability and mechanical properties. Differential scanning calorimetry results showed that the fibrous structure of PCL does not alter its crystallinity. Studies of the mechanical properties, wettability and degradability showed that the structure of the electrospun PCL improved the tensile modulus, tensile strength, wettability and biodegradability of the nanotemplates. To evaluate the nanofibrous structure of PCL on cell adhesion, osteoblasts cells were seeded on these templates. The results showed that both adhesion and proliferation of the cells is viable on these electrospun PCL membranes. Thus electrospinning is a relatively inexpensive and scalable manufacturing technique for submicron to nanometer diameter fibers, which can be of interest in the commodity industry.

scholarly journals Mechanical Properties of Oil Palm Shell Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
J. Sahari ◽  
M. A. Maleque
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Tensile Modulus ◽  
Sem Analysis ◽  
Palm Shell ◽  
Pull Out ◽  
Oil Palm Shell

The mechanical properties of oil palm shell (OPS) composites were investigated with different volume fraction of OPS such as 0%, 10%, 20%, and 30% using unsaturated polyester (UPE) as a matrix. The results presented that the tensile strength and tensile modulus of the UPE/OPS composites increased as the OPS loading increased. The highest tensile modulus of UPE/OPS was obtained at 30 vol% of OPS with the value of 8.50 GPa. The tensile strength of the composites was 1.15, 1.17, and 1.18 times higher than the pure UPE matrix for 10, 20, and 30 vol% of OPS, respectively. The FTIR spectra showed the change of functional group of composites with different volume fractions of OPS. SEM analysis shows the filler pull-out present in the composites which proved the poor filler-matrix interfacial bonding.

scholarly journals Effects of Bacillus subtilis biocementation on the mechanical properties of mortars

2019 ◽  
Vol 12 (1) ◽  
pp. 31-38 ◽  
Author(s):  
N. SCHWANTES-CEZARIO ◽  
M. F. PORTO ◽  
G. F. B. SANDOVAL ◽  
G. F. N. NOGUEIRA ◽  
A. F. COUTO ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Cementitious Materials ◽  
Mechanical Analysis ◽  
Sem Analysis ◽  
Subtilis Strain ◽  
Cement Mortars ◽  
Water To Cement Ratio ◽  
Mixing Water

Abstract This study aims to evaluate the influence of B. subtilis AP91 spores addition on the mechanical properties of mortars. B. subtilis strain AP91, isolated from rice leaves of the needle variety, which has an early cycle of production, was used at the concentration of 105 spores/mL in mortars with cement-to-sand ratio of 1:3 (by weight) and water-to-cement ratio (w/c) of 0.63. These spores were added in two different ways: in the mixing water and by immersion in a solution containing bacterial spores. Scanning Electron Microscope (SEM) analysis showed crystals with calcium peaks on the EDS, which possibly indicates the presence of bioprecipitated calcium carbonate. The results obtained in the mechanical analysis showed that the bioprecipitation of CaCO3 by B. subtilis strain AP91 was satisfactory, particularly when the spores were added in the mixing water, increasing the compressive strength up to 31%. Thus, it was concluded that the addition of B. subtilis AP91 spores in the mixing water of cement mortars induced biocementation, which increased the compressive strength. This bioprecipitation of calcium carbonate may very well have other advantageous consequences, such as the closure of pores and cracks in cementitious materials that could improve durability properties, although more research is still needed on this matter.

Revaluation of Australian palm residues in polypropylene composites: Statistical influence of fiber treatment

2020 ◽  
pp. 002199832096053 ◽  
Author(s):  
Noelle C Zanini ◽  
Rennan FS Barbosa ◽  
Alana G de Souza ◽  
Derval S Rosa ◽  
Daniella R Mulinari
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Mechanical Performance ◽  
Alkali Treatment ◽  
Mechanical Analysis ◽  
Melt Mixing ◽  
Polypropylene Composites ◽  
Matrix Interactions ◽  
Fiber Treatment ◽  
Fiber Matrix

Australian palm residues are generated by palm heart industry in large quantities and are considered an underused material with a composition rich in lignocellulosic structures. This residue is generally utilized as briquettes for energy or sheep feed; however, few works investigate this residue as composite fillers. This work aimed to revalue Australian palm residues (PR) by preparing polypropylene composites through melt mixing, using different fiber contents (0, 5, 10, 20, and 30 wt%), and evaluate the statistical influence of fibers (residues) alkali treatment (MPR) in composites mechanical properties. PR and MPR were evaluated by FTIR, XRD, SEM, TGA, and composites were assessed using thermal and mechanical analysis, in which ANOVA statistical analysis was applied. The residues addition increased the mechanical properties and their treatment enhanced the stiffness of the composites compared to pristine PP. However, ANOVA demonstrated that at low residues contents, surface treatment does not increase fiber-matrix interactions effectively, then tensile properties were statistically similar to PP. Considering tensile properties, 20% MPR showed statistically distinct properties, with significative enhancements; no filler contents dependence was verified. Flexural properties were more sensitive to residue loading, and composites with 30% PR and MPR presented superior mechanical performance. This difference is associated with a higher sensitivity of tensile stress towards fiber-matrix interactions, which was improved with fiber treatment. Also, the residues content and treatment influenced the composites' thermal stability, with better results for PP-MPR. Results indicate that palm residue is an excellent filler for improving composites' thermal and mechanical properties, with a greener character.

Poly(Butylene Succinate) Composites Reinforced with Short Sisal Fibres

2001 ◽  
Vol 9 (5) ◽  
pp. 333-338 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Retsu Makino ◽  
Ryutoku Yosomiya ◽  
Hiroyuku Takeishi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fibre Length ◽  
Mechanical Analysis ◽  
Fibre Content ◽  
Flexural Properties ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Sisal Fibre ◽  
The Matrix

Poly(butylene succinate) composites reinforced with short sisal fibre were prepared by melt mixing and subsequent injection moulding. The influence of fibre length, fibre content and the surface treatment of the natural fibres on the mechanical properties of the composites were evaluated. Regarding fibre length, the tensile and flexural properties of the composites had maxima at a fibre length of about 5 mm. The flexural and tensile moduli of the composites increased with increasing fibre content. Although the tensile strength hardly changed, the flexural strength increased up to a fibre content of 10 wt%. The dynamic mechanical analysis of the composites showed that the storage moduli at above ca.-16°C (corresponding to the glass transition temperature of the matrix) increased with increasing fibre content.

Sign in / Sign up

Export Citation Format

Share Document