scholarly journals Experimental Investigation of NaOH and KOH Mixture in SCBA-Based Geopolymer Cement Composite

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3437 ◽  
Author(s):  
Sardar Kashif Ur Rehman ◽  
Lahiba Imtiaz ◽  
Fahid Aslam ◽  
Muhammad Khizar Khan ◽  
Muhammad Haseeb ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Cement Composite ◽  
Sem Analysis ◽  
Molar Ratio ◽  
Geopolymer Concrete ◽  
Concrete Durability ◽  
Geopolymer Cement ◽  
Ash Disposal ◽  
Durability Performance

This research aimed at exploring the effects of a mixture of sodium hydroxide (NaOH) and potassium hydroxide (KOH) activators in a sugar cane bagasse ash (SCBA)-based geopolymer cement paste. Bagasse ash replacement was 20% of cement by weight. The mixture of NaOH and KOH comprised 4, 8, and 12 M solutions with mixing percentages of 0%, 20%, 40%, 60%, 80%, and 100% for all possible combinations. A pH test was performed on each possible combination of solutions. A Chapelle’s test, XRD, X-ray fluorescence (XRF), and SEM analysis were used to check whether the SCBA exhibited pozzolanic reactivity. Subsequently, the SCBA geopolymer cement paste was tested for compressive strength, water absorption, permeable porosity, and sorptivity. It was estimated that the geopolymer cement paste exhibited higher absorption and sorptivity values than control mixtures when molarity increased. However, the samples prepared with combinations of the 8 M activator solution exhibited consistent absorption, sorptivity, and compressive strength values when compared to the control and other geopolymer mixtures with 4 and 12 M activator solutions. Thus, the two activator solutions G8N408K60 and G8N208K80—where GxNayKb represents the geopolymer concrete sample prepared by adding solutions of two bases, i.e., ‘xNayKb’ showing an ‘a’ percentage of ‘x’ molar NaOH and a ‘b’ percentage of ‘y’ molar KOH—were obtained as the optimum molar ratio of the activator in geopolymer concrete. The geopolymer cement pastes, along with the optimum and control samples, were further tested for concrete durability, SEM, and TGA tests. The G8N208K80 sample exhibited a better mechanical and durability performance than the G8N408K60 sample. The durability performance of the geopolymer concrete was also superior to ordinary concrete. Moreover, the geopolymer concrete achieved a 21% reduction in global warming potential compared to the control mixture. Thus, it can be concluded that the use of SCBA in geopolymer concrete can address the ash disposal and CO2 emission problems with enhanced durability.

The Mechanism of Mineral Admixture in Cement Hydration

2012 ◽  
Vol 450-451 ◽  
pp. 1528-1531
Author(s):  
Mei Li Zhao
Keyword(s):  
Cement Paste ◽  
High Performance ◽  
Cement Hydration ◽  
High Performance Concrete ◽  
Cement Mortar ◽  
Sem Analysis ◽  
Mineral Admixture ◽  
Hydration Mechanism ◽  
Curing Period ◽  
Durability Performance

The mineral admixture is one of the indispensable materials for ordinary high-performance concrete. In this paper, the pure cement paste and cement paste replacing by mineral admixture were tested by cement mortar. The SEM analysis of pure cement paste and mineral admixture paste after curing period of 7 days and 28 days.From the picture of SEM after the period of 7 days and 28 days,the cement hydration mechanism was suspected.It could be used for explanating the physical performance and durability performance of the high perfromance concrete with mineral admixture.

scholarly journals Effect of molarity of sodium hydroxide and molar ratio of alkaline activator solution on the strength development of geopolymer concrete

2021 ◽  
Vol 309 ◽  
pp. 01058
Author(s):  
V Srinivasa Reddy ◽  
Karnati Vamsi Krishna ◽  
M V Seshagiri Rao ◽  
S Shrihari
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Ash Content ◽  
Mix Design ◽  
Molar Ratio ◽  
Strength Development ◽  
Geopolymer Concrete ◽  
Synergic Effect ◽  
Alkaline Activator

In the current study, effect of SiO2/Na2O ratio in Sodium silicate (Na2SiO3) solution, Na2SiO3/NaOH ratio and molarity of NaOH on the compressive strength of geopolymer concrete. A geopolymer mix design is formulated with various mixes are casted with alkali activator solution (AAS) / fly ash (FA) =0.5 and constant fly ash content. The molar ratio of SiO2/Na2O in Na2SiO3 solution is altered from 1.50 to 3.00 for different ratios of Na2SiO3/NaOH (2.0, 2.5 and 3.0) and also for various molarities of NaOH (8M,10M,12M,14M,16M and 18M) are studied for their synergic effect on the compressive strength of geopolymer concrete. Results highlighted that the 16M NaOH yields high compressive strength when SiO2/Na2O in Na2SiO3 solution is around 2.00 to 2.40 and Na2SiO3/NaOH=2.5.

scholarly journals Investigating Various Factors Affecting the Long-Term Compressive Strength of Heat-Cured Fly Ash Geopolymer Concrete and the Use of Orthogonal Experimental Design Method

2019 ◽  
Vol 13 (1) ◽  
Author(s):  
Hongen Zhang ◽  
Lang Li ◽  
Prabir Kumar Sarker ◽  
Tao Long ◽  
Xiaoshuang Shi ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Experimental Design ◽  
Sodium Hydroxide ◽  
Molar Ratio ◽  
Design Parameters ◽  
Orthogonal Experimental Design ◽  
Strength Increase ◽  
Geopolymer Concrete

AbstractThis work quantified the hierarchy of the influence of three common mixture design parameters on the compressive strength and the rate of strength increase over the long term of low-calcium fly ash geopolymer concrete (FAGC) through designing 16 mixtures by the orthogonal experimental design (OED) method. The parameters used in the study were liquid to fly ash (L/FA) ratio, sodium hydroxide concentration (SHC) and sodium silicate solution to sodium hydroxide solution (SS/SH) ratio. The L/FA ratio showed little effect on compressive strength when it was varied from 0.40 to 0.52. SHC showed the greatest influence on compressive strength with little impact on the rate of strength increase after the initial heat curing. Even though the SS/SH ratio showed a small effect on the initial compressive strength, it had a considerable influence on the rate of strength increase over the long term. It was found that the compressive strength at 480 days was positively related to the Na2O/SiO2 molar ratio when it was varied from 0.49 to 0.80 and the Si/Al molar ratio was increased up to 1.87. Analysis of the failure types of specimens demonstrated that compressive strength of FAGC was associated with the strength of the mortar–aggregate interface zone (MAIZ).

scholarly journals Preparation of Electric- and Magnetic-Activated Water and Its Influence on the Workability and Mechanical Properties of Cement Mortar

2021 ◽  
Vol 13 (8) ◽  
pp. 4546
Author(s):  
Kaiyue Zhao ◽  
Peng Zhang ◽  
Bing Wang ◽  
Yupeng Tian ◽  
Shanbin Xue ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Cement Paste ◽  
Cement Mortar ◽  
Environmental Issues ◽  
Chemical Admixtures ◽  
Untreated Water ◽  
Alternating Voltage

Cement-based materials prepared with activated water induced by a magnetic field or electric field represent a possible solution to environmental issues caused by the worldwide utilization of chemical admixtures. In this contribution, electric- and magnetic-activated water have been produced. The workability and mechanical properties of cement mortar prepared with this activated water have been investigated. The results indicate that the pH and absorbance (Abs) values of the water varied as the electric and magnetic field changed, and their values increased significantly, exhibiting improved activity compared with that of the untreated water. In addition, activated water still retains activity within 30 min of the resting time. The fluidity of the cement paste prepared with electric-activated water was significantly larger than that of the untreated paste. However, the level of improvement differed with the worst performance resulting from cement paste prepared with alternating voltage activated water. In terms of mechanical properties, both compressive strength and flexural strength obtained its maximum values at 280 mT with two processing cycles. The compressive strength increased 26% as the curing time increased from 7 days to 28 days and flexural strength increased by 31%. In addition, through the introduction of magnetic-activated water into cement mortar, the mechanical strength can be maintained without losing its workability when the amount of cement is reduced.

scholarly journals Effect of Calcium Nitrate on the Properties of Portland–Limestone Cement-Based Concrete Cured at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1611
Author(s):  
Gintautas Skripkiūnas ◽  
Asta Kičaitė ◽  
Harald Justnes ◽  
Ina Pundienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Calcium Nitrate ◽  
Curing Temperature ◽  
Hardened Concrete ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Early Strength

The effect of calcium nitrate (CN) dosages from 0 to 3% (of cement mass) on the properties of fresh cement paste rheology and hardening processes and on the strength of hardened concrete with two types of limestone-blended composite cements (CEM II A-LL 42.5 R and 42.5 N) at different initial (two-day) curing temperatures (−10 °C to +20 °C) is presented. The rheology results showed that a CN dosage up to 1.5% works as a plasticizing admixture, while higher amounts demonstrate the effect of increasing viscosity. At higher CN content, the viscosity growth in normal early strength (N type) cement pastes is much slower than in high early strength (R type) cement pastes. For both cement-type pastes, shortening the initial and final setting times is more effective when using 3% at +5 °C and 0 °C. At these temperatures, the use of 3% CN reduces the initial setting time for high early strength paste by 7.4 and 5.4 times and for normal early strength cement paste by 3.5 and 3.4 times when compared to a CN-free cement paste. The most efficient use of CN is achieved at −5 °C for compressive strength enlargement; a 1% CN dosage ensures the compressive strength of samples at a −5 °C initial curing temperature, with high early strength cement exceeding 3.5 MPa but being less than the required 3.5 MPa in samples with normal early strength cement.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Effect of Elevated Temperature on Mechanical Properties of High-Volume Fly Ash-Based Geopolymer Concrete, Mortar and Paste Cured at Room Temperature

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1473
Author(s):  
Jun Zhao ◽  
Kang Wang ◽  
Shuaibin Wang ◽  
Zike Wang ◽  
Zhaohui Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
High Volume ◽  
Sem Analysis ◽  
Geopolymer Concrete ◽  
Ordinary Concrete ◽  
Exposure Temperature

This paper presents results from experimental work on mechanical properties of geopolymer concrete, mortar and paste prepared using fly ash and blended slag. Compressive strength, splitting tensile strength and flexural strength tests were conducted on large sets of geopolymer and ordinary concrete, mortar and paste after exposure to elevated temperatures. From Thermogravimetric analyzer (TGA), X-ray diffraction (XRD), Scanning electron microscope (SEM) test results, the geopolymer exhibits excellent resistance to elevated temperature. Compressive strengths of C30, C40 and C50 geopolymer concrete, mortar and paste show incremental improvement then followed by a gradual reduction, and finally reach a relatively consistent value with an increase in exposure temperature. The higher slag content in the geopolymer reduces residual strength and the lower exposure temperature corresponding to peak residual strength. Resistance to elevated temperature of C40 geopolymer concrete, mortar and paste is better than that of ordinary concrete, mortar and paste at the same grade. XRD, TGA and SEM analysis suggests that the heat resistance of C–S–H produced using slag is lower than that of sulphoaluminate gel (quartz and mullite, etc.) produced using fly ash. This facilitates degradation of C30, C40 and C50 geopolymer after exposure to elevated temperatures.

Using of Untreated Carbon Nanotubes in Cement Compositions

2016 ◽  
Vol 865 ◽  
pp. 6-11 ◽  
Author(s):  
Kateryna Pushkarova ◽  
Maryna Sukhanevych ◽  
Artur Martsikh
Keyword(s):  
Carbon Nanotubes ◽  
Cement Paste ◽  
Cementitious Materials ◽  
Positive Influence ◽  
Mechanical Tests ◽  
Strength Characteristics ◽  
Concrete Durability ◽  
Cement Mortars ◽  
Optimum Decision ◽  
Cement System

One of the most important problem of concrete durability is increasing of waterproofing. Researches are devoted studying of cement mortars modified by carbon nanotubes, dispersed in plasticizers solutions. Were investigated physico-mechanical properties of cement paste, cement-sand mortar into which structure entered untreated carbon nanotubes (production of plant TM "Spetsmash" Kyiv, Ukraine) in various quantity. Were used as plasticizers in cement compositions additives substances of the various chemical nature – naphtaleneformaldehyde, melamineformaldehyde and polycarboxylate. Quantity of untreated nanotubes varied from 0,5%; 1,0% and to 1,5%. Concentration of additives was accepted taking into account recommendations of producers and made about 1% from the weight of cement. Were studied some technological processes of introduction untreated carbon nanotubes in cement system and is shown that the way of introduction of nanomodifiers has essential impact on strength characteristics of cementitious materials. Optimum decision introduction of untreated carbon nanotubes is using its in dispersion plasticizer of the working concentration prepared in an ultrasonic dispergator is established. Results of physico-mechanical tests of cement paste and cement-sand mortar showed positive influence at introduction of untreated carbon nanotubes as cement modifiers on strength characteristics of samples. Resalts is shown that the nanomodifier, used quantity about 1% in solution of lignosulfonate with polycarboxylate and melamineformaldehyde plasticizer has great impact on strength characteristics.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Sign in / Sign up

Export Citation Format

Share Document