scholarly journals Mechanical Simulation of Thermoplastic Composite Fiber Variable-Angle Laminates

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3374 ◽  
Author(s):  
Zhongliang Cao ◽  
Dengke Guo ◽  
Hongya Fu ◽  
Zhenyu Han
Keyword(s):  
Mechanical Properties ◽  
Maximum Stress ◽  
Thermoplastic Composite ◽  
Fiber Direction ◽  
Analysis Model ◽  
Maximum Deformation ◽  
Minimum Value ◽  
Maximum Value ◽  
Variable Angle ◽  
Point Parameter

By changing the placement angle of the placement path, the fiber direction can be controlled and adjusted to change the load distribution in the laminate, and the stress and natural frequency performances of the laminate can then be altered to finally obtain laminates with desired mechanical properties. In this paper, the finite element analysis model of variable-stiffness laminates is established based on the fiber placement reference path defined by the Bezier curve method. Based on the analysis of the mechanical properties of the thermoplastic fiber variable-angle laminates obtained by variable-angle trajectory planning, the changes in the stress and deformation of the thermoplastic fiber variable-angle laminate with the connection point parameter β under a compressive load are analyzed. The influence of the parameter β on the static performances of the variable-angle laminates is studied. The simulation results indicate that the maximum stress of the laminate increases first and then decreases as the parameter β increases and reaches the maximum value when the parameter β is 0.5. The minimum stress also shows the same trend as that of the maximum stress and reaches the minimum value when the connection point parameter β is 0.3. The deformation of the variable-angle laminates varies with the change of the connection point parameter β. The maximum deformation increases at first and then decreases for the laminate with the parameter β increasing and reaches the maximum value when the parameter β is 0.8. The minimum deformation of the laminate decreases initially and then increases as the connection point parameter β increases and reaches the minimum value when the parameter β is 0.6. The deformation gradually decreases from the upper and lower ends to the middle, and the deformation area has a symmetrical form. The initial regular rectangular area gradually changes to an elliptical distribution and the area of maximum deformation gradually decreases.

Finite Element Analysis on Mechanical Properties of Lathe Spindle

2013 ◽  
Vol 378 ◽  
pp. 97-101 ◽  
Author(s):  
Y.M. Yu
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Maximum Stress ◽  
Practical Significance ◽  
Production Cycle ◽  
Vibration Modes ◽  
Ansys Software ◽  
Element Analysis ◽  
Maximum Deformation

The ANSYS software was used to carry out finite element analysis on the mechanical properties of lathe spindle, taking C7620 lathe as research object. By static analysis, the maximum deformation and maximum stress value of spindle in specific operation were determined. Furthermore, spring-damper element was adopted to simulate elastic supports of bearing in dynamic analysis, and then the natural frequencies of the first five ranks and vibration modes of spindle were obtained. The research results in this paper have theoretical and practical significance in optimizing the design of lathe spindle parts and shortening production cycle.

Mechanics Analysis of Overhanging Submarine Pipeline Based on ANSYS

2014 ◽  
Vol 556-562 ◽  
pp. 1232-1235
Author(s):  
Yuan Yong Liu ◽  
Fang Li ◽  
Xiu Ting Wei
Keyword(s):  
Maximum Stress ◽  
Calculated Data ◽  
Submarine Pipeline ◽  
Analysis Model ◽  
Element Analysis ◽  
Maximum Deformation ◽  
Oil Pipeline ◽  
Transition Length ◽  
Stress And Deformation ◽  
Important Significance

Stress analysis model of overhanging section of pipeline is created through submarine oil pipeline as analysis object, stress conditions of actual working conditions is considered, transition length is introduced to proceed finite element analysis of the pipeline, ANSYS software is used to calculate the stress and deformation of pipeline under different overhanging length in this paper. The curves of the maximum stress and maximum deformation with overhanging span are made, the variations of the maximum stress and maximum deformation are obtained according to the calculated data. This study provides data support for the failure identification of submarine oil pipeline, which has an important significance for the overhanging analysis and treatment of submarine pipeline.

Static Finite Element Analysis of Container Flooring and Chassis Combinations

2010 ◽  
Vol 160-162 ◽  
pp. 389-394
Author(s):  
Quan Zhong Wang ◽  
Chang Jiang He ◽  
Bin Xu
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Maximum Stress ◽  
New Combination ◽  
Original Structure ◽  
Element Analysis ◽  
Cross Sectional ◽  
Maximum Deformation ◽  
The Difference ◽  
Sectional Shape

We analyzed static finite element of the container flooring and chassis combination structure rolling by a car; then, we analyzed the maximum deformation and corresponding maximum stress of the flooring and chassis combination when chassis crossbeam cross-sectional shape from the U-shaped to the I-shaped and compared with the original structure with the same force, as well as the space between the central crossbeam decreased, we can see that, the appropriate crossbeam space can obviously increase the stiffness of the container and reduce the stress of the structure; at the same time, we analyzed the combinations which with different flooring structures, we can see that the difference deformation between the new combination and the original was small, so we know that the mechanical properties of flooring had little effect to the mechanical properties of the entire combination.

Mechanical Properties of Native Tree Species for Soil Bioengineering in Northeastern Mexico

2020 ◽  
Author(s):  
Rebeca Zavala ◽  
Israel Cantú ◽  
Laura Sánchez ◽  
Humberto González ◽  
Eduardo Estrada ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
Small Scale ◽  
Ligustrum Lucidum ◽  
Soil Bioengineering ◽  
Minimum Value ◽  
Cercis Canadensis ◽  
Maximum Value ◽  
Celtis Laevigata

<p>In recent years, the effect of soil bioengineering has played a very important role on slope stability. However, our area of study is constantly under the influence of small-scale earthquakes and extreme events of heavy rainfall which cause potentially unstable conditions on the slopes. The mechanical properties of the root systems tensile strength (T<sub>s</sub>) and modulus of elasticity (E<sub>root</sub>) of four native species were analyzed for a potential use as soil bioengineering elements. We investigated if tensile strength (N/mm<sup>2</sup>) and modulus of elasticity of roots (N/mm<sup>2</sup>) was different between studied species: <em>Cercis canadensis</em>, <em>Celtis laevigata</em>, <em>Quercus rysophylla</em> and <em>Ligustrum lucidum</em>. The species considered were selected based on their native characteristics and widespread existence on the slopes. Regarding tree forest species, the tests were conducted with the Universal Testing Machine Shimadzu type SLFL-100KN. The relationships among root diameter, tensile strength (T<sub>s</sub>), and modulus of elasticity (E<sub>root</sub>) was negative and could be fitted with a power regression equation, showing highly significant   values p<0.01.Celtis laevigata showed the maximum value of tensile strength (T<sub>s</sub>) 28.11 N/mm<sup>2</sup> while the minimum value of tensile strength was observed in <em>Ligustrum lucidum</em> 5.27 N/mm<sup>2</sup>. For the variable modulus of elasticity (E<sub>root</sub>) <em>Celtis laevigata</em>  showed the maximum value of 90.01N/mm<sup>2</sup> while the minimum value of modulus of elasticity was observed in <em>Ligustrum lucidum</em> 29.16 N/mm<sup>2</sup>.Results of mechanical proprieties are showed the following ascending order: <em>Ligustrum lucidum</em> < <em>Quercus rysophylla</em> < <em>Cercis canadensis</em> < <em>Celtis laevigata</em>. Likewise, <em>Celtis laevigata</em> showed the highest tensile strength and modulus of elasticity of all investigated species.</p><p> </p><p>Key words: root, tensile strength, modulus or elasticity.</p><p> </p><p> </p>

Physico-Chemical Characteristics of Sapota (Chikoo) Powder based Value Added Pasta Product using Semolina (Suji) and Maida

2020 ◽  
Vol 7 (04) ◽  
Author(s):  
SATYA NARAYAN SINGH ◽  
RAJESH G BURBADE ◽  
HITESH SANCHAVAT ◽  
P S PANDIT
Keyword(s):  
Bulk Density ◽  
Crude Protein ◽  
Water Solubility ◽  
Value Added ◽  
Absorption Capacity ◽  
Oil Absorption ◽  
Minimum Value ◽  
Maximum Value ◽  
Physico Chemical ◽  
Specific Length

The cereals of today are more nutritious and healthful than ever before. Cereals processing is one of the oldest and the most essential part of all food technologies. Pasta products and noodles have been staple foods since ancient times in many countries all over the world. In this study pasta formulation was substituted with blending sapota powder in different proportions (4 levels i.e. 0%, 10%, 20%, 30%) into semolina and maida flour separately. Pasta products were prepared using eight different formulations and adding water (approximately 31% of total weight) in DOLLY pasta extruder machine. All the samples were evaluated for physical properties: specific length (mm/g), bulk density (kg/m3), specific density (kg/m3) and porosity (%); functional properties: water absorption index (%), water solubility index (%) and oil absorption capacity (ml/g) and nutritional compositions: moisture (%), crude protein (%), fat (%) and carbohydrate (%). Highest specific length 36.20 mm/g was observed for T5 treatment, low bulk density 368.10 kg/m3 was observed for T5 and highest porosity 9.24% was found for T1 treatment. The maximum WAI, WSI values 325.83%, 17.33% respectively was observed for T1 treatment and minimum value of oil absorption capacity 1.06 ml/g for T8 treatment. The moisture content of dried pasta products was found in the range of 6 to 7%. The maximum value of crude protein 13.07% was found for T5 and minimum value 8.81% for T4 treatments. The fat contents were varied from 1.02% to 1.28 %. The maximum value of carbohydrate was 76.20% for T1 and minimum value 65.41% for T8.

Bionic design of the tower for wind turbine

2021 ◽  
pp. 095440622110046
Author(s):  
Yuqiao Zheng ◽  
Fugang Dong ◽  
Huquan Guo ◽  
Bingxi Lu ◽  
Zhengwen He
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Maximum Stress ◽  
Natural Frequencies ◽  
Bionic Design ◽  
Analytic Hierarchy ◽  
Element Analysis ◽  
Maximum Deformation ◽  
Overall Stability ◽  
Biological Selection

The study obtains a methodology for the bionic design of the tower for wind turbines. To verify the rationality of the biological selection, the Analytic Hierarchy Procedure (AHP) is applied to calculate the similarity between the bamboo and the tower. Creatively, a bionic bamboo tower (BBT) is presented, which is equipped with four reinforcement ribs and five flanges. Further, finite element analysis is employed to comparatively investigate the performance of the BBT and the original tower (OT) in the static and dynamic. Through the investigation, it is suggested that the maximum deformation and maximum stress can be reduced by 5.93 and 13.75% of the BBT. Moreover, this approach results in 3% and 1.1% increase respectively in the First two natural frequencies and overall stability.

scholarly journals Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

2021 ◽  
Vol 22 (7) ◽  
pp. 3391
Author(s):  
Sylwia Grabska-Zielińska ◽  
Alina Sionkowska ◽  
Ewa Olewnik-Kruszkowska ◽  
Katarzyna Reczyńska ◽  
Elżbieta Pamuła
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Physicochemical Properties ◽  
Silk Fibroin ◽  
Three Dimensional ◽  
Microscopy Imaging ◽  
Maximum Deformation ◽  
One Step ◽  
Chitosan Blends ◽  
Fourier Transfer Infrared Spectroscopy

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

scholarly journals Functional Bionanocomposite Fibers of Chitosan Filled with Cellulose Nanofibers Obtained by Gel Spinning

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1563
Author(s):  
Sofia Marquez-Bravo ◽  
Ingo Doench ◽  
Pamela Molina ◽  
Flor Estefany Bentley ◽  
Arnaud Kamdem Tamo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Cellulose Nanofibers ◽  
Microstructural Characterization ◽  
Fiber Formation ◽  
Fiber Direction ◽  
Composite Fibers ◽  
X Ray Diffraction ◽  
Gel Spinning ◽  
X Ray

Extremely high mechanical performance spun bionanocomposite fibers of chitosan (CHI), and cellulose nanofibers (CNFs) were successfully achieved by gel spinning of CHI aqueous viscous formulations filled with CNFs. The microstructural characterization of the fibers by X-ray diffraction revealed the crystallization of the CHI polymer chains into anhydrous chitosan allomorph. The spinning process combining acidic–basic–neutralization–stretching–drying steps allowed obtaining CHI/CNF composite fibers of high crystallinity, with enhanced effect at incorporating the CNFs. Chitosan crystallization seems to be promoted by the presence of cellulose nanofibers, serving as nucleation sites for the growing of CHI crystals. Moreover, the preferential orientation of both CNFs and CHI crystals along the spun fiber direction was revealed in the two-dimensional X-ray diffraction patterns. By increasing the CNF amount up to the optimum concentration of 0.4 wt % in the viscous CHI/CNF collodion, Young’s modulus of the spun fibers significantly increased up to 8 GPa. Similarly, the stress at break and the yield stress drastically increased from 115 to 163 MPa, and from 67 to 119 MPa, respectively, by adding only 0.4 wt % of CNFs into a collodion solution containing 4 wt % of chitosan. The toughness of the CHI-based fibers thereby increased from 5 to 9 MJ.m−3. For higher CNFs contents like 0.5 wt %, the high mechanical performance of the CHI/CNF composite fibers was still observed, but with a slight worsening of the mechanical parameters, which may be related to a minor disruption of the CHI matrix hydrogel network constituting the collodion and gel fiber, as precursor state for the dry fiber formation. Finally, the rheological behavior observed for the different CHI/CNF viscous collodions and the obtained structural, thermal and mechanical properties results revealed an optimum matrix/filler compatibility and interface when adding 0.4 wt % of nanofibrillated cellulose (CNF) into 4 wt % CHI formulations, yielding functional bionanocomposite fibers of outstanding mechanical properties.

Analysis and Optimization of the Static and Dynamic Characteristics of Head Frame

2011 ◽  
Vol 418-420 ◽  
pp. 2055-2059 ◽  
Author(s):  
Yu Lin Wang ◽  
Na Jin ◽  
Kai Liao ◽  
Rui Jin Guo ◽  
Hu Tian Feng
Keyword(s):  
Machine Tool ◽  
Dynamic Characteristics ◽  
Maximum Stress ◽  
Dynamic Performance ◽  
Mode Shapes ◽  
Cnc Machine ◽  
Static And Dynamic Characteristics ◽  
Maximum Deformation ◽  
Improvement Measures ◽  
Optimal Measure

The head frame is a key component which plays a supportive and accommodative role in the spindle system of CNC machine tool. Improving the static and dynamic characteristics has profound significance to the development of machine tool and product performance. The simplified finite element modal is established with ANSYS to carry out the static and modal analysis. The results showed that the maximum deformation of the head frame was 0.0066mm, the maximum stress was 3.94Mpa, the deformation of most region was no more than 0.0007mm, which all verified that the head frame had a good stiffness and deforming resistance; several improvement measures for dynamic performance were also proposed by analyzing the mode shapes, and the 1st order natural frequency increased 7.33% while the head frame mass only increased 1.58% applying the optimal measure, which improved the dynamic characteristics of the head frame effectively.

scholarly journals Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1954
Author(s):  
Yang Liu ◽  
Xun Zhang ◽  
Quanxin Gao ◽  
Hongliang Huang ◽  
Yongli Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Maleic Anhydride ◽  
Ag Nanoparticles ◽  
Decomposition Temperature ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Maximum Value ◽  
Polyolefin Elastomer ◽  
Local Defects

In the present study, silver (Ag) nanoparticles and maleic anhydride-grafted polyolefin elastomer (MAH-g-POE) were used as enhancement additives to improve the performance of the polyoxymethylene (POM) homopolymer. Specifically, the POM/Ag/MAH-g-POE ternary nanocomposites with varying Ag nanoparticles and MAH-g-POE contents were prepared by a melt mixing method. The effects of the additives on the microstructure, thermal stability, crystallization behavior, mechanical properties, and dynamic mechanical thermal properties of the ternary nanocomposites were studied. It was found that the MAH-g-POE played a role in the bridging of the Ag nanoparticles and POM matrix and improved the interfacial adhesion between the Ag nanoparticles and POM matrix, owing to the good compatibility between Ag/MAH-g-POE and the POM matrix. Moreover, it was found that the combined addition of Ag nanoparticles and MAH-g-POE significantly enhanced the thermal stability, crystallization properties, and mechanical properties of the POM/Ag/MAH-g-POE ternary nanocomposites. When the Ag/MAH-g-POE content was 1 wt.%, the tensile strength reached the maximum value of 54.78 MPa. In addition, when the Ag/MAH-g-POE content increased to 15wt.%, the elongation at break reached the maximum value of 64.02%. However, when the Ag/MAH-g-POE content further increased to 20 wt.%, the elongation at break decreased again, which could be attributed to the aggregation of excessive Ag nanoparticles forming local defects in the POM/Ag/MAH-g-POE ternary nanocomposites. Furthermore, when the Ag/MAH-g-POE content was 20 wt.%, the maximum decomposition temperature of POM/Ag/MAH-g-POE ternary nanocomposites was 398.22 °C, which was 71.39 °C higher than that of pure POM. However, compared with POM, the storage modulus of POM/Ag/MAH-g-POE ternary nanocomposites decreased with the Ag/MAH-g-POE content, because the MAH-g-POE elastomer could reduce the rigidity of POM.

Sign in / Sign up

Export Citation Format

Share Document