scholarly journals Calibration of Steel Rings for the Measurement of Strain and Shrinkage Stress for Cement-Based Composites

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2963
Author(s):  
Adam Zieliński ◽  
Maria Kaszyńska
Keyword(s):  
Measurement Errors ◽  
High Performance ◽  
Test Bench ◽  
High Performance Concrete ◽  
Mechanical Design ◽  
Calibration Method ◽  
Theory Of Elasticity ◽  
Strain Gauges ◽  
Shrinkage Stress ◽  
Shrinkage Process

Concrete shrinkage is a phenomenon that results in a decrease of volume in the composite material during the curing period. The method for determining the effects of restrained shrinkage is described in Standard ASTM C 1581/C 1581M–09a. This article shows the calibration of measuring rings with respect to the theory of elasticity and the analysis of the relationship of steel ring deformation to high-performance concrete tensile stress as a function of time. Steel rings equipped with strain gauges are used for measurement of the strain during the compression of the samples. The strain is caused by the shrinkage of the concrete ring specimen that tightens around steel rings. The method allows registering the changes to the shrinkage process in time and evaluating the susceptibility of concrete to cracking. However, the standard does not focus on the details of the mechanical design of the test bench. To acquire accurate measurements, the test bench needs to be calibrated. Measurement errors may be caused by an improper, uneven installation of strain gauges, imprecise geometry of the steel measuring rings, or incorrect equipment settings. The calibration method makes it possible to determine the stress in a concrete sample leading to its cracking at specific deformation of the steel ring.

Live-Load Test Results of Missouri’s First High-Performance Concrete Superstructure Bridge

2003 ◽  
Vol 1845 (1) ◽  
pp. 96-103 ◽  
Author(s):  
Yumin Yang ◽  
John J. Myers
Keyword(s):  
Load Distribution ◽  
High Performance ◽  
High Performance Concrete ◽  
Large Diameter ◽  
Load Test ◽  
Strain Gauges ◽  
Live Load ◽  
Test Results ◽  
Live Load Distribution ◽  
Live Load Test

For its significant economical savings and greater design flexibility, high-performance concrete (HPC) is becoming more widely used in highway bridge structures. High-performance bridges with HPC and large-diameter prestressed strands are becoming attractive to designers. Bridge A6130 is the first fully HPC superstructure bridge in Missouri. The bridge has HPC cast-in-place deck and high-strength concrete girders reinforced with 15.2-mm (0.6-in.) diameter strands. The bridge was instrumented with embedded strain gauges and thermocouples to monitor the early-age and later-age behavior of the structures from construction through service. To investigate the overall behavior of the bridge under live load, a static live-load test was developed and carried out. During the live-load test, 64 embedded vibrating wire strain gauges and 14 embedded electrical-resistance strain gauges were used to acquire the changing strain rate in the bridge caused by the varying live-load conditions. Girder deflections and rotations were also recorded with external sensors and a data acquisition system. Based on the test results, the load distribution to the girders was studied. The AASHTO specifications live-load distribution factor recommended for design was compared with the measured value and found to be overly conservative. The AASHTO load and resistance factor design live-load distribution factors recommended for design were found to be comparable to measured values. Two finite element models were developed with ANSYS and compared with measured values to investigate the continuity level of the Missouri Department of Transportation interior bent detail.

scholarly journals Cost-Effective High-Performance Concrete: Experimental Analysis on Shrinkage

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2730
Author(s):  
Barbara Kucharczyková ◽  
Dalibor Kocáb ◽  
Petr Daněk ◽  
Ivailo Terzijski
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Setting Time ◽  
Mechanical Strain ◽  
Cost Effective ◽  
Strain Gauges ◽  
Early Age ◽  
Dry Air ◽  
First Case

This paper focuses on the experimental determination of the shrinkage process in Self-Compacting High-Performance Concrete (SCC HPC) exposed to dry air and autogenous conditions. Special molds with dimensions of 100 mm × 60 mm × 1000 mm and 50 mm × 50 mm × 300 mm equipped with one movable head are used for the measurement. The main aim of this study is to compare the shrinkage curves of SCC HPC, which were obtained by using different measurement devices and for specimens of different sizes. In addition, two different times t0 are considered for the data evaluation to investigate the influence of this factor on the absolute value of shrinkage. In the first case, t0 is the time of the start of measurement, in the second case, t0 is the setting time. The early-shrinkage (48 h) is continuously measured using inductive sensors leant against the movable head and with strain gauges embedded inside the test specimen. To monitor the long term shrinkage, the specimens are equipped with special markers, embedded into the specimens’ upper surface or ends. These markers serve as measurement bases for the measurement using mechanical strain gauges. The test specimens are demolded after 48 h and the long term shrinkage is monitored using the embedded strain gauges (inside the specimens) and mechanical strain gauges that are placed, in regular intervals, onto the markers embedded into the specimens’ surface or ends. The results show that both types of measurement equipment give a similar result in the case of early age measurement, especially for the specimens cured under autogenous conditions. However, the early age and especially long term measurement are influenced by the position of the measurement sensors, particularly in the case of specimens cured under dry air conditions. It was proven that the time t0 have a fundamental influence on the final values of the shrinkage of investigated SCC HPC and have a significant impact on the conclusions on the size effect.

Study on Application of Concrete Admixture Technology

2013 ◽  
Vol 438-439 ◽  
pp. 54-57
Author(s):  
Wen Cui
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Field Application ◽  
Hydration Heat ◽  
Mix Design ◽  
Shrinkage Stress ◽  
Simulation Test

Mix design of high performance concrete was determined based on the pumping simulation test. It was indicated by test and field application that the trimixture technique and the double mixture technique can improve the pump of concrete, reduce the dosage of cement and the hydration heat; adding expansion agent can prevent harmful cracks in the concrete due to shrinkage stress, improve the compactness and impermeability. The reasonable construction technologies were used in mixing, transportation, pouring, vibrating and curing of the concrete in order to ensure quality of the construction.

Effect of the Expansion Agent on Early-Age Autogenous Shrinkage Stress of Concrete

2013 ◽  
Vol 838-841 ◽  
pp. 564-568
Author(s):  
Pan Xiu Wang
Keyword(s):  
Tensile Strength ◽  
Concrete Structure ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Shrinkage Strain ◽  
Shrinkage Stress ◽  
Early Age ◽  
Concrete Cube

Early-age autogenous shrinkage is key problem of high performance concrete. It can cause a lot of early-age cracks in concrete structure and further endanger the permeability and durability. Adding expansion agent can control the early-age autogenous shrinkage strain and reduce the risk of early-age cracks. In this paper, the early-age autogenous shrinkage stress of concrete cube is calculated. The results show that, early-age autogenous shrinkage stress is larger than early-age tensile strength of concrete. So some cracks occur on the surface of concrete structure. By adding expansion agent, the early-age autogenous shrinkage strain and stress both decreases.

Shrinkage Cracking of High Performance Concrete Mixed with Steel Slag Admixture

2011 ◽  
Vol 462-463 ◽  
pp. 867-871 ◽  
Author(s):  
Yun Feng Li ◽  
Hua Xun Guo ◽  
Ling Ling Wang
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Steel Slag ◽  
Concrete Structures ◽  
Mineral Admixtures ◽  
Maintenance Cost ◽  
Shrinkage Stress ◽  
Early Age ◽  
Restrained Shrinkage ◽  
Shrinkage Cracking

Cracking due to the restrained shrinkage stress has been frequently observed at early age in concrete structures. Early-age deterioration of concrete due to cracking and higher maintenance cost for poor durability cause serious troubles to concrete structures. Steel slag includes a certain scale mineral such as C2S and C3S, and can be applied in cement and concrete as mineral admixtures. Two tests are outlined to quantify the behaviour of concrete under restrained shrinkage using plate and ring specimens. The results show that mineral admixtures can be used to reduce cracking in concrete. The risk of cracking can be estimated for steel slag concrete, so that it will improve the durability of concrete structures.

scholarly journals Minimization of the Influence of Shear-Induced Particle Migration in Determining the Rheological Characteristics of Self-Compacting Mortars and Concretes

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1542
Author(s):  
Christian Baumert ◽  
Harald Garrecht
Keyword(s):  
Grain Size ◽  
Rheological Properties ◽  
Measurement Errors ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Particle Migration ◽  
Main Hypothesis ◽  
Lower Shear ◽  
Determination Of Parameters

Determining the exact rheological properties of cementitious materials in fundamental units is a crucial step in concrete science. It is undisputed that before measuring rheological properties in concrete rheometers, it is necessary to pre-shear the fresh mortar or concrete. Due to the migration of the coarse particles into areas with lower shear stress, however, segregation takes place. An experimental set-up was developed to determine the effects on the measured values of the concrete rheometer ICAR. This allows the active homogenization (pre-shearing) of the material before each change of speed. In the tests higher raw values (macroscopic data) could be measured. This clearly influences the calculated rheological Bingham parameters and modified Bingham parameters for a self-compacting concrete (SCC) with a maximum grain size of 16 mm. Therefore, the homogeneity of the material, a main hypothesis of rheological measurements, does not seem to be fulfilled with the coaxial rheometer used. The process of the indispensable pre-shearing therefore requires more attention in the future so that measurement errors can be minimized. Especially in numerical simulation, suitable rheological models and the realistic determination of parameters are crucial. Since the shear-induced particle migration is largely dependent on the maximum grain size, an ultra-high performance concrete (UHPC) with a maximum particle size of only 0.5 mm was also investigated in the laboratory mixer KNIELE KKM-RT. The integrated rheometer enables also the active homogenization of the fresh concrete during pre-shearing but without the danger of over-mixing, as it is the case for the experimental ICAR setup. This article proves that relevant differences can also be identified for such a material.

The Influence of Chemical Admixtures on the Autogenous Shrinkage Ultra-High Performance Concrete

2010 ◽  
Vol 452-453 ◽  
pp. 725-728 ◽  
Author(s):  
Jung Jun Park ◽  
Sung Wook Kim ◽  
Gum Sung Ryu ◽  
Kwang Myung Lee
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Pulse Velocity ◽  
Reducing Agent ◽  
Shrinkage Stress ◽  
Early Age ◽  
Ultra High Performance Concrete ◽  
Expansive Additive ◽  
Shrinkage Reducing Agent

Ultra-high performance concrete (UHPC) is a material developing remarkable performance with compressive strength of about 200 MPa and flexural strength of approximately 30 MPa on which research is actively conducted today. However, UHPC is also characterized by a mixing composed of a high specific quantity of binder that is a W/B ratio of about 0.2, which requires to examine the effects of the autogenous shrinkage. Accordingly, this study investigates the effects of the use of expansive additive and water reducing agent on the autogenous shrinkage of UHPC at early age. To that goal, autogenous shrinkage test and ultrasonic pulse velocity (UPV) monitoring are conducted for a mixing of UHPC using expansive additive and shrinkage reducing agent. The experimental results reveal that the autogenous shrinkage of UHPC reduces by 24% for a mix of UHPC adopting both 7.5% of expansive additive and 1% of shrinkage reducing agent compared to the mix without admixture. Furthermore, this mix is seen to compensate the autogenous shrinkage occurring at early age when UHPC develops its largest stiffness in view of the UPV evolution curve. At that time, the shrinkage stress seems to be extremely softened.

scholarly journals Synergistic Benefits of Using Expansive and Shrinkage Reducing Admixture on High-Performance Concrete

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2514 ◽  
Author(s):  
Tian-Feng Yuan ◽  
Seong-Kyum Kim ◽  
Kyung-Teak Koh ◽  
Young-Soo Yoon
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Shrinkage Stress ◽  
Early Age ◽  
Test Results ◽  
Shrinkage Cracking ◽  
Shrinkage Cracks ◽  
Shrinkage Reducing Admixture

High-performance concrete (HPC) is widely used in construction according to great mechanical properties, but it has a high risk of shrinkage cracking due to autogenous shrinkage stress. Therefore, the aim of this research was to investigate the effect of a combination of expansive admixture (EA) and shrinkage reducing admixture (SA) on the autogenous shrinkage of high-performance concrete without heat treatment. Two different EA to cement weight ratios of 0.0, 5.0%, and two different SA to cement weight ratios of 0.0, and 1.0% were combined and considered. To investigate the differences in the time-zero conditions effect on the autogenous shrinkage behaviors, four different initial points were compared. The test results indicate that the EA and/or SA content was conductive to a little bite increase compressive strength (22.6–37.9%) and tensile strength (<4.8%). According to the synergistic effect of the EA and SA on the HPC, the autogenous shrinkage significantly decreased (<50%), as compared to those specimens with only one type of admixture (EA or SA). Furthermore, all the specimens incurred restrained autogenous shrinkage cracks at an early age, except the specimen using the combined EA and SA. Therefore, it can be concluded that the combination of EA and SA is effective for improving the properties of HPC.

scholarly journals Evaluation of the Thermal and Shrinkage Stresses in Restrained High-Performance Concrete

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3680 ◽  
Author(s):  
Yang Yang ◽  
Linhao Ma ◽  
Jie Huang ◽  
Chunping Gu ◽  
Zhenjian Xu ◽  
...  
Keyword(s):  
Thermal Stress ◽  
High Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Shrinkage Stress ◽  
Early Age ◽  
Volume Deformation ◽  
Curing Conditions ◽  
Drying Shrinkage Stress

The early age volume deformation is the main course for the cracking of high-performance concrete (HPC). Hence, the shrinkage behavior and the restrained stress development of HPC under different restraints and curing conditions were experimentally studied in this paper. The method to separate the stress components in the total restraint stress was proposed. The total restrained stress was separated into autogenous shrinkage stress, drying shrinkage stress and thermal stress. The results showed that the developments of the free shrinkage (autogenous shrinkage and drying shrinkage) and the restrained stress were accelerated when the drying began; but the age when the drying began did not significantly influence the long-term shrinkage and restrained stress of HPC; the autogenous shrinkage stress continuously contributed to the development of the total restrained stress in HPC; the drying shrinkage stress developed very rapidly soon after the drying began; and the thermal stress was generated when the temperature dropped. The thermal stress was predominant at the early age, but the contributions of the three stresses to the total restrained stress were almost the same at the age of 56 d in this study.

Calibration of K&C Concrete Model for UHPC in LS-DYNA

2014 ◽  
Vol 1081 ◽  
pp. 254-259 ◽  
Author(s):  
Man Xu ◽  
Kay Wille
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Laboratory Data ◽  
Material Model ◽  
Calibration Method ◽  
Material Behavior ◽  
Uniaxial Compression Test ◽  
Concrete Material ◽  
Material Parameters ◽  
Concrete Model

Karagozian & Case Concrete (KCC) model in LS-DYNA is a parameter automatically generated material model for simulation of concrete. By giving the unconfined compressive strength of the concrete material, all other constitutive material parameters will be generated by the model. It is a valuable concrete model for users who have no laboratory data or conduct tentative simulations. However, the automatically generated parameters will induce error when the concrete material behavior deviates from the regular behavior. In this research, a calibration method is introduced to show a simple way for generating input material parameters of ultra-high performance concrete (UHPC). Empirical equations for triaxial compressive tests are used here for the calibration. The calibrated model is firstly checked by the simulation of uniaxial compression test with one element and the results reveal that the calibrated model shows a better agreement with the test data than the parameter automatically generated KCC model.

Sign in / Sign up

Export Citation Format

Share Document