scholarly journals Minimization of the Influence of Shear-Induced Particle Migration in Determining the Rheological Characteristics of Self-Compacting Mortars and Concretes

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1542
Author(s):  
Christian Baumert ◽  
Harald Garrecht
Keyword(s):  
Grain Size ◽  
Rheological Properties ◽  
Measurement Errors ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Particle Migration ◽  
Main Hypothesis ◽  
Lower Shear ◽  
Determination Of Parameters

Determining the exact rheological properties of cementitious materials in fundamental units is a crucial step in concrete science. It is undisputed that before measuring rheological properties in concrete rheometers, it is necessary to pre-shear the fresh mortar or concrete. Due to the migration of the coarse particles into areas with lower shear stress, however, segregation takes place. An experimental set-up was developed to determine the effects on the measured values of the concrete rheometer ICAR. This allows the active homogenization (pre-shearing) of the material before each change of speed. In the tests higher raw values (macroscopic data) could be measured. This clearly influences the calculated rheological Bingham parameters and modified Bingham parameters for a self-compacting concrete (SCC) with a maximum grain size of 16 mm. Therefore, the homogeneity of the material, a main hypothesis of rheological measurements, does not seem to be fulfilled with the coaxial rheometer used. The process of the indispensable pre-shearing therefore requires more attention in the future so that measurement errors can be minimized. Especially in numerical simulation, suitable rheological models and the realistic determination of parameters are crucial. Since the shear-induced particle migration is largely dependent on the maximum grain size, an ultra-high performance concrete (UHPC) with a maximum particle size of only 0.5 mm was also investigated in the laboratory mixer KNIELE KKM-RT. The integrated rheometer enables also the active homogenization of the fresh concrete during pre-shearing but without the danger of over-mixing, as it is the case for the experimental ICAR setup. This article proves that relevant differences can also be identified for such a material.

scholarly journals Durability Study on High-Performance Fiber-Reinforced Mortar under Simulated Wastewater Pipeline Environment

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3781
Author(s):  
Tianyu Wang ◽  
Yahong Zhao ◽  
Baosong Ma ◽  
Cong Zeng
Keyword(s):  
Mass Loss ◽  
Pore Volume ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Economic Losses ◽  
Structural Deterioration ◽  
Simulated Wastewater ◽  
Corrosive Environments

The acid–alkaline-inducd corrosive environments inside wastewater concrete pipelines cause concrete structural deterioration and substantial economic losses all over the world. High-performance concrete/mortar (HPC) was designed to have better resistance to corrosive environments, with enhanced service life. However, the durability of HPC in wastewater pipeline environments has rarely been studied. A high-performance mortar mixture (M) reinforced by supplemental materials (including fly ash and silica fume) and polyvinyl alcohol (PVA) fibers, together with a mortar mixture (P) consisting of cement, sand and water with similar mechanical performance, were both designed and exposed to simulated wastewater pipeline environments. The visual appearance, dimensional variation, mass loss, mechanical properties, permeable pore volume, and microstructure of the specimens were measured during the corrosion cycles. More severe deterioration was observed when the alkaline environment was introduced into the corrosion cycles. Test results showed that the M specimens had less permeable pore volume, better dimensional stability, and denser microstructure than the P specimens under acid–alkaline-induced corrosive environments. The mass-loss rates of the M specimens were 66.1–77.2% of the P specimens after 12 corrosion cycles. The compressive strength of the M specimens was 25.5–37.3% higher than the P specimens after 12 cycles under corrosive environments. Hence, the high-performance mortar examined in this study was considered superior to traditional cementitious materials for wastewater pipeline construction and rehabilitation.

Research Progress on Early Autogenous Shrinkage of Cement-Based Cementitious Materials

2013 ◽  
Vol 634-638 ◽  
pp. 2738-2741
Author(s):  
Wei Huang ◽  
Tao Zhang ◽  
Yun Yun Xu
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Research Work ◽  
Autogenous Shrinkage ◽  
Cementitious Materials ◽  
Mineral Admixtures ◽  
Research Progress ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Improvement Measures

Concrete autogenous shrinkage phenomenon would adversely affect the mechanical properties and durability of concrete, this phenomenon is important. Autogenous shrinkage problem of low water-cement ratio of the with high mineral admixtures, cement-based cementitious materials was introduced. The main reason for high-performance concrete early cracking being autogenous shrinkage was pointed out. Based on the home and abroad research status of low water cement ratio of the cement paste and concrete autogenous shrinkage, especially for early autogenous shrinkage phenomenon, the mechanism of autogenous shrinkage and the measure method is presented, and the improvement measures and the possible problems the need for further research work is presented.

Repair of Severely Damaged Reinforced Concrete Beams with High-Strength Cementitious Grout

2020 ◽  
Vol 2674 (6) ◽  
pp. 372-384
Author(s):  
Antoine N. Gergess ◽  
Mahfoud Shaikh Al Shabab ◽  
Razane Massouh
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Cementitious Materials ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Rc Beams ◽  
Rc Structures

High-strength cementitious materials such as high-performance concrete are extensively used for retrofit of reinforced concrete (RC) structures. The effectiveness of these materials is increased when mixed with steel fibers. A commonly used technique for strengthening and repair of RC beams consists of applying high-performance fiber-reinforced concrete jackets around the beam perimeter. This paper investigates the jacketing method for repairing severely damaged RC beams. Four 2 m (6 ft 63/4 in.) long rectangular RC beams, 200 × 300 mm (8 ×12 in.) were initially cast and loaded until failure based on three-point bending tests. The four beams were then repaired by thickening the sides of the damaged RC beams using a commercially available high-strength shrinkage grout with and without steel fibers. Strain and deformation were recorded in the damaged and repaired beams to compare structural performance. It is shown that the flexural strength of the repaired beams is increased and the crack pattern under loading is improved, proving that the proposed repair method can restore the resistance capacity of RC beams despite the degree of damage. A method for repair is proposed and an analytical investigation is also performed to understand the structural behavior of the repaired beams based on different thickening configurations.

The Effect of Homogenization Procedure on Mechanical Properties of High-Performance Concrete with Partial Replacement of Cement by Supplementary Cementitious Materials

2019 ◽  
Vol 292 ◽  
pp. 102-107 ◽  
Author(s):  
Josef Fládr ◽  
Petr Bílý ◽  
Karel Šeps ◽  
Roman Chylík ◽  
Vladimír Hrbek
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Water Content ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Depth Of Penetration ◽  
Cement Additive

High-performance concrete is a very specific type of concrete. Its production is sensitive to both the quality of compounds used and the order of addition of particular compounds during the homogenization process. The mechanical properties were observed for four dosing procedures of each of the three tested concrete mixtures. The four dosing procedures were identical for the three mixes. The three mixes varied only in the type of supplementary cementitious material used and in water content. The water content difference was caused by variable k-value of particular additives. The water-to-binder ratio was kept constant for all the concretes. The additives used were metakaolin, fly ash and microsilica. The comparison of particular dosing procedures was carried out on the values of basic mechanical properties of concrete. The paper compares compressive strength and depth of penetration of water under pressure. Besides the comparsion of macro-mechanical properties, the effect of microsilica and fly ash additives on micro-mechanical properties was observed with the use of scanning electron microscopy (SEM) and nanoindentation data analysis. Nanoindentation was used to determine the thickness and strength of interfacial transition zone (ITZ) for different sequence of addition of cement, additive and aggregate. The thickness obtained by nanoindentation was further investigated by SEM EDS line scanning.

scholarly journals The Compressive Strength of High-Performance Concrete and Ultrahigh-Performance

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
E. H. Kadri ◽  
S. Aggoun ◽  
S. Kenai ◽  
A. Kaci
Keyword(s):  
Experimental Data ◽  
Compressive Strength ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Strength Gain ◽  
Proposed Model ◽  
Partial Cement Replacement ◽  
Better Than

The compressive strength of silica fume concretes was investigated at low water-cementitious materials ratios with a naphthalene sulphonate superplasticizer. The results show that partial cement replacement up to 20% produce, higher compressive strengths than control concretes, nevertheless the strength gain is less than 15%. In this paper we propose a model to evaluate the compressive strength of silica fume concrete at any time. The model is related to the water-cementitious materials and silica-cement ratios. Taking into account the author's and other researchers’ experimental data, the accuracy of the proposed model is better than 5%.

scholarly journals Effect of Graphene Oxide Nanosheets on Physical Properties of Ultra-High-Performance Concrete with High Volume Supplementary Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1929 ◽  
Author(s):  
Yu-You Wu ◽  
Jing Zhang ◽  
Changjiang Liu ◽  
Zhoulian Zheng ◽  
Paul Lambert
Keyword(s):  
Graphene Oxide ◽  
Physical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Slump Flow

Nanomaterials have been increasingly employed for improving the mechanical properties and durability of ultra-high-performance concrete (UHPC) with high volume supplementary cementitious materials (SCMs). Recently, graphene oxide (GO) nanosheets have appeared as one of the most promising nanomaterials for enhancing the properties of cementitious composites. To date, a majority of studies have concentrated on cement pastes and mortars with fewer investigations on normal concrete, ultra-high strength concrete, and ultra-high-performance cement-based composites with a high volume of cement content. The studies of UHPC with high volume SCMs have not yet been widely investigated. This paper presents an experimental investigation into the mini slump flow and physical properties of such a UHPC containing GO nanosheets at additions from 0.00 to 0.05% by weight of cement and a water–cement ratio of 0.16. The study demonstrates that the mini slump flow gradually decreases with increasing GO nanosheet content. The results also confirm that the optimal content of GO nanosheets under standard curing and under steam curing is 0.02% and 0.04%, respectively, and the corresponding compressive and flexural strengths are significantly improved, establishing a fundamental step toward developing a cost-effective and environmentally friendly UHPC for more sustainable infrastructure.

Influence of Hydration Temperature on Durability and Mechanical Property Performance of Prestressed and Precast High-Performance Concrete Beams

2000 ◽  
Vol 1696 (1) ◽  
pp. 131-142 ◽  
Author(s):  
John J. Myers ◽  
Ramon L. Carrasquillo
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Concrete Technology ◽  
The North ◽  
Texas Department ◽  
Concrete Temperature ◽  
Temperature Development ◽  
The Impact ◽  
Property Performance

Concrete technology has continued to advance throughout the years to meet the demands of designers and innovative structural systems. With the advent of high-performance concrete (HPC), which contains large amounts of cementitious materials, the investigation of the impact of concrete temperature development during hydration on concrete performance is of keen interest. Match-curing technology was used to investigate the influence of concrete temperature development during hydration on the mechanical and material property performance of prestressed and precast HPC beams. These members were fabricated for use in two recently constructed HPC bridges in Texas. The investigation was conducted in conjunction with the design, instrumentation, and construction of the Louetta Road Overpass in Houston, Texas, and the North Concho River US-87 and South Orient Railroad Overpass in San Angelo, Texas. FHWA and the Texas Department of Transportation cosponsored these projects as part of the Strategic Highway Research Program to stimulate the use of HPC and to demonstrate the suitability of HPC in highway structures. The results of the study indicated that for HPCs that contain large amounts of cementitious materials, the concrete temperature during hydration can have a dramatic impact on both the mechanical and the material (durability) performance of the concrete. Temperature recommendations are provided to avoid less than optimal concrete performance on the basis of the member shapes and mix designs investigated in the study.

Study Progress on Modern Green High Performance Concrete at Domestic and Foreign

2013 ◽  
Vol 859 ◽  
pp. 207-212
Author(s):  
Zhao Yu Fu ◽  
Mei Ling Huang
Keyword(s):  
Sustainable Development ◽  
Research And Development ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Recycled Concrete ◽  
Green Concrete ◽  
Research Status ◽  
Study Progress ◽  
Research Situation

Recycled concrete is one of the main measures to develop ecological and green concrete, also it is one of the useful ways to obtain sustainable development of buildings, resources,and environment . Conforming to this idea , it is increasingly being valued by engineering and became one of the hot concrete research. In this paper, we start with the concept of green high performance concrete , taking high performance concrete in green cementitious materials, aggregates and admixtures point to cut in ,and describing the characteristics of green high performance concrete and its research situation in details. Besides,on the basis of combining the domestic and foreign development of green concrete,I will point out the problems in the currentre research of recycled concrete .Then Ill give the corresponding countermeasures and propose sustainable research and development proposals by emphatically analyzed the research status and application of recycled concrete at domestic and foreign .

Sign in / Sign up

Export Citation Format

Share Document