scholarly journals CeO2:Mn3O4 Catalytic Micro-Converters Tuned for CH4 Detection Based on Catalytic Combustion under Real Operating Conditions

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2196
Author(s):  
Cristian E. Simion ◽  
Ovidiu G. Florea ◽  
Mihaela Florea ◽  
Florentina Neaţu ◽  
Ştefan Neaţu ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Normal Pressure ◽  
Operating Regime ◽  
Operating Conditions ◽  
Molar Ratio ◽  
Atmospheric Conditions ◽  
X Ray ◽  
Temperature Programmed ◽  
Co Precipitation ◽  
Adsorption Desorption

Mesoporous CeO2:Mn3O4 materials (3:7 and 7:3 molar ratio) were prepared by co-precipitation and deposited as porous thick films over alumina (Al2O3) planar substrate provided with Pt meander. The aim was oriented towards detecting low levels methane (CH4) at moderate operating temperatures. Herein we demonstrated that the sensitivity of catalytic micro-converters (CMCs) towards a given peak of CH4 concentration corresponds to specific gas-surface interaction phenomena. More precisely, a transition from thermal conductivity to combustion rate is likely to occur when CMCs are operated under real atmospheric conditions (normal pressure, presence of relative humidity, and constant operating temperature). The response to CH4 was analyzed over different gas flows and different gas concentrations under the same operating regime. The materials were fully characterized by adsorption-desorption isotherms, H2-Temperature Programmed Reduction (H2-TPR), X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Raman spectroscopies. Thus, the applicative aspect of using CeO2:Mn3O4 as moderate temperature CMC for CH4 detection is brought to the fore.

scholarly journals Synthesis of DME by CO2 hydrogenation over La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts

2017 ◽  
Vol 23 (1) ◽  
pp. 49-56 ◽  
Author(s):  
Yajing Zhang ◽  
Yu Zhang ◽  
Fu Ding ◽  
Kangjun Wang ◽  
Wang Xiaolei ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Direct Synthesis ◽  
Catalytic Performance ◽  
Co2 Hydrogenation ◽  
Precipitation Method ◽  
X Ray ◽  
Temperature Programmed ◽  
And Performance ◽  
Co Precipitation ◽  
Adsorption Desorption

A series of La2O3-modified CuO-ZnO-ZrO2/HZSM-5 catalysts were prepared by an oxalate co-precipitation method. The catalysts were fully characterized by X-ray diffraction (XRD), N2 adsorption-desorption, hydrogen temperature pro-grammed reduction (H2-TPR), ammonia temperature programmed desorption (NH3-TPD), and X-ray photoelectron spectroscopy (XPS) techniques. The effect of the La2O3 content on the structure and performance of the catalysts was thoroughly investigated. The catalysts were evaluated for the direct synthesis of dimethyl ether (DME) from CO2 hydrogenation. The results displayed that La2O3 addition enhanced catalytic performance, and the maximal CO2 conversion (34.3%) and DME selectivity (57.3%) were obtained over the catalyst with 1% La2O3, which due to the smaller size of Cu species and a larger ratio of Cu+/Cu.

scholarly journals Catalytic Activity of Mixed Al2O3-ZrO2 Oxides for Glucose Conversion into 5-Hydroxymethylfurfural

Catalysts ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 878 ◽  
Author(s):  
Benjamín Torres-Olea ◽  
Sandra Mérida-Morales ◽  
Cristina García-Sancho ◽  
Juan Antonio Cecilia ◽  
Pedro Maireles-Torres
Keyword(s):  
Catalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Molar Ratio ◽  
X Ray ◽  
Zirconium Oxides ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Secondary Reactions ◽  
Temperature Programmed ◽  
Adsorption Desorption

In the present work, a series of catalysts based on aluminum and zirconium oxides was studied for the transformation of glucose into 5-hydroxymethylfurfural. These catalysts were characterized by using experimental techniques, such as X-ray diffraction, N2 adsorption–desorption at −196 °C, X-ray photoelectron spectroscopy, temperature-programmed desorption of NH3 and CO2, and scanning transmission electron microscopy. The catalytic behavior in glucose dehydration was evaluated in a water-methyl isobutyl ketone biphasic system, in the presence of CaCl2, in order to minimize losses due to unwanted secondary reactions. High glucose conversion and 5-hydroxymethylfurfural (HMF) yield values were obtained in the presence of an Al(Zr)Ox catalyst with an Al:Zr molar ratio of 7:3, reaching 97% and 47%, respectively, at 150 °C after 120 min. Under tested conditions, this catalyst retained most of its catalytic activity for four reuses.

scholarly journals Zn-Al Mixed Oxides Decorated with Potassium as Catalysts for HT-WGS: Preparation and Properties

Catalysts ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1094 ◽  
Author(s):  
Katarzyna Antoniak-Jurak ◽  
Paweł Kowalik ◽  
Kamila Michalska ◽  
Wiesław Próchniak ◽  
Robert Bicki
Keyword(s):  
Photoelectron Spectroscopy ◽  
Mixed Oxides ◽  
Catalyst Activity ◽  
Molar Ratio ◽  
X Ray ◽  
Molar Ratios ◽  
Mixed Oxide Catalysts ◽  
Wgs Reaction ◽  
Temperature Programmed ◽  
Co Precipitation

A set of ex-ZnAl-LDHs catalysts with a molar ratio of Zn/Al in the range of 0.3–1.0 was prepared using co-precipitation and thermal treatment. The samples were characterized using various methods, including X-ray fluorescence spectroscopy (XRF), X-ray photoelectron spectroscopy (XPS), X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy FT-IR, N2 adsorption, Temperature-programmed desorption of CO2 (TPD-CO2) as well as Scanning electron microscopy (SEM-EDS). Catalyst activity and long-term stability measurements were carried out in a high-temperature water–gas shift (HT-WGS) reaction. Mixed oxide catalysts with various Zn/Al molar ratios decorated with potassium showed high activity in the HT-WGS reaction within the temperature range of 330–400 °C. The highest activity was found for the Zn/Al molar ratio of 0.5 corresponding to spinel stoichiometry. However, the catalyst with a stoichiometric spinel molar ratio of Zn/Al (ZnAl_0.5_K) revealed a higher tendency for surface migration and/or vaporization of potassium during overheating at 450 °C. The correlation of the activity results and TPD-CO2 data show that medium basic sites enhance the progress of the HT-WGS reaction.

Synthesis and characterizations of TiN–SBA-15 mesoporous materials for CO2 dry reforming enhancement

2020 ◽  
Vol 92 (4) ◽  
pp. 545-556
Author(s):  
Maslin Chotirach ◽  
Supawan Tantayanon ◽  
Duangamol Nuntasri Tungasmita ◽  
Junliang Sun ◽  
Sukkaneste Tungasmita
Keyword(s):  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
High Specific Surface Area ◽  
Dry Reforming ◽  
Dry Reforming Of Methane ◽  
Ni Catalyst ◽  
X Ray ◽  
Novel Approach ◽  
Temperature Programmed ◽  
Adsorption Desorption

AbstractA novel approach of titanium nitride (TiN) incorporated into SBA-15 framework was developed using one-step hydrothermal synthesis method. TiN contents up to ~18 wt% were directly dispersed in a synthetic gel under a typical strong acidic condition. The physico-chemical characteristics and the surface properties were investigated by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), N2 adsorption-desorption, field emission scanning electron microscope (FESEM) equipped with energy dispersive X-ray spectroscopy (EDS), wavelength dispersive X-ray fluorescence (WDXRF) and CO2-temperature programmed desorption (CO2-TPD). The results indicated that the highly ordered mesostructured was effectively maintained with high specific surface area of 532–685 m2g−1. The basicity of the modified SBA-15 increased with rising TiN loading. These modified materials were applied as a support of Ni catalyst in dry reforming of methane (DRM). Their catalytic behavior possessed superior conversions for both CO2 and CH4 with the highest H2/CO ratio (0.83) as well as 50 % lower carbon formation, compared to bare SBA-15 support.

scholarly journals Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1771 ◽  
Author(s):  
Stefan Neatu ◽  
Mihaela M. Trandafir ◽  
Adelina Stănoiu ◽  
Ovidiu G. Florea ◽  
Cristian E. Simion ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Mixed Oxides ◽  
Sol Gel ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Programmed ◽  
Catalytic Combustion Of Methane ◽  
Adsorption Desorption

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium–manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2–temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2–MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3–Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2–TPR and therefore more reactive oxygen species.

Hydroformylation of Dicyclopentadiene over Rh Catalysts Supported on Fe2O3, Co3O4 and Fe2O3–Co3O4 Mixed Oxide

2017 ◽  
Vol 42 (1) ◽  
pp. 8-13 ◽  
Author(s):  
Yubo Ma ◽  
Zhixian Gao ◽  
Wumanjiang Eli
Keyword(s):  
Mixed Oxide ◽  
Photoelectron Spectroscopy ◽  
Supported Catalyst ◽  
Precipitation Method ◽  
X Ray ◽  
Analysis Techniques ◽  
Rh Catalyst ◽  
Temperature Programmed ◽  
Co Precipitation ◽  
Effect Of The Support

Rh catalysts supported on Fe2O3, Co3O4 and Fe2O3–Co3O4 mixed oxide were prepared by the co-precipitation method. The effect of the support on the performance of the Rh catalysts for the hydroformylation of dicyclopentadiene was investigated using X-ray photoelectron spectroscopy, H2-temperature-programmed reduction, H2-temperature-programmed desorption and Brunauer–Emmett–Teller analysis techniques. The results indicated that the Fe2O3–Co3O4 supported catalyst had a higher dispersion of Rh and thus more Rh+ sites. As a result, the Fe2O3–Co3O4 supported Rh catalyst exhibited higher activity compared with counterparts supported on Fe2O3 and Co3O4.

scholarly journals Heterogeneous Fenton-like oxidation of p-hydroxybenzoic acid using Fe/CeO2-TiO2 catalyst

2019 ◽  
Vol 79 (7) ◽  
pp. 1276-1286 ◽  
Author(s):  
Tijani Hammedi ◽  
Mohamed Triki ◽  
Mayra G. Alvarez ◽  
Jordi Llorca ◽  
Abdelhamid Ghorbel ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Molar Ratio ◽  
Hydroxybenzoic Acid ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Temperature Programmed

Abstract This paper is built on the Fenton-like oxidation of p-hydroxybenzoic acid (p–HBZ) in the presence of H2O2 and 3%Fe supported on CeO2-TiO2 aerogels under mild conditions. These catalysts were deeply characterized by X-ray diffraction (XRD), hydrogen temperature programmed reduction (H2-TPR), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and X-ray photoelectron spectroscopy (XPS). The effect of thermal treatment, pH (2–3, 5, 7), H2O2/p–HBZ molar ratio (5, 15, 20, 25) and reaction temperature (25 °C, 40 °C and 60 °C) on the catalytic properties of supported Fe catalysts are studied. Our results highlight the role of CeO2 and the calcination of the catalyst to obtain the highest catalytic properties after 10 min: 73% of p–HBZ conversion and 52% of total organic carbon (TOC) abatement.

scholarly journals Effect of Residual Na+ on the Combustion of Methane over Co3O4 Bulk Catalysts Prepared by Precipitation

Catalysts ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 427 ◽  
Author(s):  
Andoni Choya ◽  
Beatriz de Rivas ◽  
Jose Gutiérrez-Ortiz ◽  
Rubén López-Fonseca
Keyword(s):  
Photoelectron Spectroscopy ◽  
Near Infrared ◽  
Diffuse Reflectance Spectroscopy ◽  
Negative Impact ◽  
Methane Combustion ◽  
Molar Ratio ◽  
Temperature Programmed Reduction ◽  
X Ray ◽  
Two Samples ◽  
Temperature Programmed

The effect of the presence of residual sodium (0.4 %wt) over a Co3O4 bulk catalyst for methane combustion was studied. Two samples, with and without residual sodium, were synthesized by precipitation and thoroughly characterised by X-ray diffraction (XRD), N2 physisorption, Wavelength Dispersive X-ray Fluorescence (WDXRF), temperature-programmed reduction with hydrogen followed by temperature-programmed reduction with oxygen (H2-TPR/O2-TPO), temperature-programmed reaction with methane (CH4-TPRe), ultraviolet–visible–near-infrared diffuse reflectance spectroscopy (UV-vis-NIR DRS), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). It was found that during calcination, a fraction of the sodium atoms initially deposited on the surface diffused and migrated into the spinel lattice, inducing a distortion that improved its textural and structural properties. However, surface sodium had an overall negative impact on the catalytic activity. It led to a reduction of surface Co3+ ions in favour of Co2+, thus ultimately decreasing the Co3+/Co2+ molar ratio (from 1.96 to 1.20) and decreasing the amount and mobility of active lattice oxygen species. As a result, the catalyst with residual sodium (T90 = 545 °C) was notably less active than its clean counterpart (T90 = 500 °C). All of this outlined the significance of a proper washing when synthesizing Co3O4 catalyst using a sodium salt as the precipitating agent.

Synthesis and characterization of pure and nanosized hydroxyapatite bioceramics

2017 ◽  
Vol 6 (2) ◽  
pp. 149-157 ◽  
Author(s):  
Aneela Anwar ◽  
Qudsia Kanwal ◽  
Samina Akbar ◽  
Aisha Munawar ◽  
Arjumand Durrani ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Calcium Nitrate ◽  
Temperature Stability ◽  
Molar Ratio ◽  
Calcium Nitrate Tetrahydrate ◽  
High Temperature Stability ◽  
X Ray ◽  
Transmission Electron ◽  
Nanosized Hydroxyapatite ◽  
Co Precipitation

AbstractSynthetic nanosized hydroxyapatite (HA) particles (<120 nm) were prepared using a co-precipitation technique by adopting two different routes – one from an aqueous solution of calcium nitrate tetrahydrate and diammonium hydrogen phosphate at pH 10 and the other by using calcium hydroxide and phosphoric acid as precursors at pH 8.5 and reaction temperature of 50°C. The lattice parameters of HA nanopowder were analogous to reference [Joint Committee on Powdered Diffraction Standards (JCPDS)] pattern no. 09-432. No decomposition of HA into other phases was observed even after heating at 1000°C in air for 1 h. This observation revealed the high-temperature stability of the HA nanopowder obtained using co-precipitation route. The effects of preliminary Ca/P molar ratio, precipitation, pH and temperature on the evolution of phase and crystallinity of the nanopowder were systematically examined and optimized. The product was evaluated by techniques such as X-ray-diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) and Raman spectroscopy analyses. The chemical structural analysis of the as-prepared HA sample was performed using X-ray photoelectron spectroscopy (XPS). After heat treatment at 1000°C for 1 h and ageing for 15 h, the product was obtained as a phase-pure, highly crystalline HA nanorods.

Study of Preparation, Characterization and Temperature-Programmed Reduction of NiO-ZnO Binary Materials

2013 ◽  
Vol 664 ◽  
pp. 515-520
Author(s):  
Chih Wei Tang ◽  
Jiunn Jer Hwang ◽  
Shie Hsiung Lin ◽  
Chin Chun Chung
Keyword(s):  
Weight Percent ◽  
Precipitation Method ◽  
Temperature Programmed Reduction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Surface Areas ◽  
Temperature Programmed ◽  
Co Precipitation ◽  
Adsorption Desorption

The NiO-ZnO binary materials had been prepared by co-precipitation method. The weight percent of nickel of NiO-ZnO materials were 5, 10 and 20; they were pretreated under air at temperature of 300, 500 and 700°C, respectively. The characterization of NiO-ZnO materials were the thermal gravity analysis(TGA), X-ray diffraction(XRD), N2 adsorption-desorption at 77K, scaning electron microscope(SEM) and temperature-programmed reduction(TPR). The results revealed that surface areas of NiO-ZnO materials order from large to small were 20NiZn(OH)x(66 m2·g-1) > 10NiZn(OH)x(34 m2·g-1) > 5NiZn(OH)x(9 m2·g-1) after being calcined at the temperature of 500°C. Further, NiO-ZnO materials had two main reductive peaks at 390-415°C and 560-657°C, respectively. In all NiO-ZnO materials, 20NiZn(OH)x-C500 material had the highest surface area and the best interaction between NiO and ZnO.

Sign in / Sign up

Export Citation Format

Share Document