scholarly journals Effects of Material Nonlinearities on Design of Composite Constructions—Elasto-Plastic Behaviour

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1792 ◽  
Author(s):  
Aleksander Muc
Keyword(s):  
Cylindrical Shell ◽  
Composite Structures ◽  
Pressure Vessels ◽  
Experimental Results ◽  
Matrix Cracking ◽  
Elastic Analysis ◽  
Limit States ◽  
Numerical Examples ◽  
Linear Elastic ◽  
Linear Behaviour

Usually, the design of composite structures is limited to the linear elastic analysis only. The experimental results discussed in the paper demonstrate the physical non-linear behaviour both for unidirectional and woven roving composites. It is mainly connected with the micromechanical damages in composite structures, particularly with the effects of matrix cracking modeled in the form of elastic-plastic physical relations. In the present paper, the effects of both physical and geometrical non-linearities are taken into account. Their influence on the limit states (understood in the sense of buckling or failure/damage) of composite structures is discussed. The numerical examples deal with the behaviour of composite pressure vessels components, such as a cylindrical shell and the reinforcement of the junction of shells. The optimisation method of the reinforcement thickness is also formulated and solved herein.

Stresses in compact end closures for cylindrical pressure vessels

1969 ◽  
Vol 4 (1) ◽  
pp. 57-64
Author(s):  
R W T Preater
Keyword(s):  
Cylindrical Shell ◽  
Rigid Body ◽  
Optimum Design ◽  
Cross Section ◽  
Experimental Verification ◽  
Pressure Vessels ◽  
Rigid Body Motion ◽  
Experimental Results ◽  
Body Motion ◽  
Annular Ring

Three different assumptions are made for the behaviour of the junction between the cylindrical shell and the end closure. Comparisons of analytical and experimental results show that the inclusion of a ‘rigid’ annular ring beam at the junction of the cylider and the closure best represents the shell behaviour for a ratio of cylinder mean radius to thickness of 3–7, and enables a prediction of an optimum vessel configuration to be made. Experimental verification of this optimum design confirms the predictions. (The special use of the term ‘rigid’ is taken in this context to refer to a ring beam for which deformations of the cross-section are ignored but rigid body motion is permitted.)

Lower Bound Limit Load Estimation Using a Linear Elastic Analysis

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
C. Hari Manoj Simha ◽  
R. Adibi-Asl
Keyword(s):  
Lower Bound ◽  
Deformation Theory ◽  
Elastic Stress ◽  
Limit Load ◽  
Load Estimation ◽  
Elastic Analysis ◽  
Numerical Examples ◽  
Linear Elastic ◽  
Plastic Localization ◽  
Appl Math

We present a scheme that utilizes one elastic stress field (no iterations) to compute lower bound limit load multipliers of structures that collapse through gross (or localized) plasticity. A criterion to distinguish between these collapse modes is presented. For structures that collapse through gross plasticity, we demonstrate that the m′ multiplier proposed by Mura et al. (1965, Extended Theorems of Limit Analysis,” Q. Appl. Math., 23(2), pp. 171–179) is a lower bound in the context of deformation theory. For structures that undergo plastic localization at collapse, we present a criterion that identifies (approximately) the subvolumes of the structure that participate in the collapse. Multiplier m′ is computed over the selected subvolumes, denoted as m'S, and demonstrated to be a lower bound multiplier in the context of deformation theory. We consider numerical examples of structures that collapse by localized or gross plasticity and show that our proposed multiplier is lower than the corresponding multiplier obtained through elastic–plastic analysis and the proposed multiplier is not overly conservative.

scholarly journals A FEM analysis of the settlement of a tall building situated on loess subsoil

2020 ◽  
Vol 10 (1) ◽  
pp. 519-526
Author(s):  
Krzysztof Nepelski
Keyword(s):  
Fem Analysis ◽  
Actual Process ◽  
Linear Elastic ◽  
Perfectly Plastic ◽  
Modified Cam Clay ◽  
Linear Behaviour ◽  
Subsequent Calculation ◽  
Elastic Perfectly Plastic ◽  
Subsoil Model ◽  
Storey Building

AbstractIn order to correctly model the behaviour of a building under load, it is necessary to take into account the displacement of the subsoil under the foundations. The subsoil is a material with typically non-linear behaviour. This paper presents an example of the modelling of a tall, 14-storey, building located in Lublin. The building was constructed on loess subsoil, with the use of a base slab. The subsoil lying directly beneath the foundations was described using the Modified Cam-Clay model, while the linear elastic perfectly plastic model with the Coulomb-Mohr failure criterion was used for the deeper subsoil. The parameters of the subsoil model were derived on the basis of the results of CPT soundings and laboratory oedometer tests. In numerical FEM analyses, the floors of the building were added in subsequent calculation steps, simulating the actual process of building construction. The results of the calculations involved the displacements taken in the subsequent calculation steps, which were compared with the displacements of 14 geodetic benchmarks placed in the slab.

Local loads on a toroidal shell

1992 ◽  
Vol 27 (2) ◽  
pp. 59-66 ◽  
Author(s):  
D Redekop ◽  
F Zhang
Keyword(s):  
Cylindrical Shell ◽  
Shell Theory ◽  
Elastic Shell ◽  
Toroidal Shell ◽  
Pipe Bend ◽  
Local Loads ◽  
Simply Supported ◽  
Linear Elastic ◽  
Wide Range ◽  
Theory Solution

In this study the effect of local loads applied on a sectorial toroidal shell (pipe bend) is considered. A linear elastic shell theory solution for local loads is first outlined. The solution corresponds to the case of a shell simply supported at the two ends. Detailed displacement and stress results are then given for a specific shell with loadings centred at three positions; the crown circles, the extrados, and the intrados. These results are compared with results for a corresponding cylindrical shell. The paper concludes with a table summarizing results for characteristic displacements and stresses in a number of shells, covering a wide range of geometric parameters.

A Noncyclic Method for Determination of Accumulated Strain in Stainless Steel 304 Pressure Vessels

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Gongfeng Jiang ◽  
Gang Chen ◽  
Liang Sun ◽  
Yiliang Zhang ◽  
Xiaoliang Jia ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Internal Pressure ◽  
Pressure Vessel ◽  
Peak Stress ◽  
Pressure Vessels ◽  
Experimental Results ◽  
Elastic Domain ◽  
Ratcheting Strain ◽  
Stainless Steel 304 ◽  
Accumulated Strain

Experimental results of uniaxial ratcheting tests for stainless steel 304 (SS304) under stress-controlled condition at room temperature showed that the elastic domain defined in this paper expands with accumulation of plastic strain. Both ratcheting strain and viscoplastic strain rates reduce with the increase of elastic domain, and the total strain will be saturated finally. If the saturated strain and corresponded peak stress of different experimental results under the stress ratio R ≥ 0 are plotted, a curve demonstrating the material shakedown states of SS304 can be constituted. Using this curve, the accumulated strain in a pressure vessel subjected to cyclic internal pressure can be determined by only an elastic-plastic analysis, and without the cycle-by-cycle analysis. Meanwhile, a physical experiment of a thin-walled pressure vessel subjected to cyclic internal pressure has been carried out to verify the feasibility and effectiveness of this noncyclic method. By comparison, the accumulated strains evaluated by the noncyclic method agreed well with those obtained from the experiments. The noncyclic method is simpler and more practical than the cycle-by-cycle method for engineering design.

Strength Loss in Composite Cylinders Under Impact

1988 ◽  
Vol 110 (2) ◽  
pp. 180-184 ◽  
Author(s):  
A. P. Christoforou ◽  
S. R. Swanson
Keyword(s):  
Composite Structures ◽  
Composite Plates ◽  
Strength Loss ◽  
Pressure Vessels ◽  
Fourier Series Expansion ◽  
Lateral Impact ◽  
Low Velocity ◽  
Expansion Procedure ◽  
The Impact ◽  
Composite Cylinders

The problem of strength loss in composite structures due to impact appears to be important due to the sensitivity of advanced composites to these loadings. Although a number of studies have been carried out on impact of flat composite plates, relatively little work has been done on tubular geometries such as pressure vessels despite the usage in applications. We have addressed the problem of calculating strength loss due to low velocity, lateral impact of composite cylinders. In our model we use an existing Fourier Series expansion procedure to calculate ply stresses and strains, compare these values with allowables to predict fiber breakage during the impact, and finally use fracture mechanics to predict the strength loss due to the impact. Although the model is quite simplified, the general trends of experiments appear to be represented.

scholarly journals Variation Simulation of Fixtured Assembly Processes for Compliant Structures Using Piecewise-Linear Analysis

2005 ◽  
Author(s):  
Michael L. Stewart ◽  
Kenneth W. Chase
Keyword(s):  
Piecewise Linear ◽  
Element Model ◽  
Linear Analysis ◽  
Elastic Analysis ◽  
Variation Analysis ◽  
Linear Elastic ◽  
Final Assembly ◽  
Compliant Part ◽  
Assembly Operations ◽  
Variation Simulation

While variation analysis methods for compliant assemblies are becoming established, there is still much to be done to model the effects of multi-step, fixtured assembly processes statistically. A new method is introduced for statistically analyzing compliant part assembly processes using fixtures. This method yields both a mean and a variant solution, which can characterize an entire population of assemblies. The method, called Piecewise-Linear Elastic Analysis, or PLEA, is developed for predicting the residual stress, deformation and springback variation resulting from fixtured assembly processes. A comprehensive, step-by-step analysis map is presented for introducing dimensional and surface variations into a finite element model, simulating assembly operations, and calculating the error in the final assembly. PLEA is validated on a simple, laboratory assembly and a more complex, production assembly. Significant modeling issues are resolved as well as the comparison of the analytical to physical results.

Implementation of p and h-p Versions of the Finite Element Method

1992 ◽  
Author(s):  
Ye-Chen Lai ◽  
Timothy C. S. Liang ◽  
Zhenxue Jia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Elastic Analysis ◽  
Two Dimensional ◽  
The Finite Element Method ◽  
Shape Functions ◽  
Linear Elastic ◽  
Finite Element Software ◽  
Analysis Process ◽  
Adaptive Analysis

Abstract Based on hierarchic shape functions and an effective convergence procedure, the p-version and h-p adaptive analysis capabilities were incorporated into a finite element software system, called COSMOS/M. The range of the polynomial orders can be varied from 1 to 10 for two dimensional linear elastic analysis. In the h-p adaptive analysis process, a refined mesh are first achieved via adaptive h-refinement. The p-refinement is then added on to the h-version designed mesh by uniformly increasing the degree of the polynomials. Some numerical results computed by COSMOS/M are presented to illustrate the performance of these p and h-p analysis capabilities.

Sign in / Sign up

Export Citation Format

Share Document