scholarly journals Amino Anthraquinone: Synthesis, Characterization, and Its Application as an Active Material in Environmental Sensors

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 960
Author(s):  
Salman Ali ◽  
Muhammad Tahir ◽  
Nasir Mehboob ◽  
Fazal Wahab ◽  
Steven J. Langford ◽  
...  
Keyword(s):  
Active Material ◽  
Xrd Analysis ◽  
Environmental Sensors ◽  
X Ray Diffraction ◽  
Electrode Gap ◽  
Linear Change ◽  
Sensing Applications ◽  
Atomic Force ◽  
Potential Applications ◽  
Hydrophobic Material

This work reports synthesis, thin film characterizations, and study of an organic semiconductor 2-aminoanthraquinone (AAq) for humidity and temperature sensing applications. The morphological and phase studies of AAq thin films are carried out by scanning electron microscope (SEM), atomic force microscope (AFM), and X-ray diffraction (XRD) analysis. To study the sensing properties of AAq, a surface type Au/AAq/Au sensor is fabricated by thermally depositing a 60 nm layer of AAq at a pressure of ~10−5 mbar on a pre-patterned gold (Au) electrodes with inter-electrode gap of 45 µm. To measure sensing capability of the Au/AAq/Au device, the variations in its capacitance and resistance are studied as a function of humidity and temperature. The Au/AAq/Au device measures and exhibits a linear change in capacitance and resistance when relative humidity (%RH) and temperature are varied. The AAq is a hydrophobic material which makes it one of the best candidates to be used as an active material in humidity sensors; on the other hand, its high melting point (575 K) is another appealing property that enables it for its potential applications in temperature sensors.

Low Molecular Weight Microfibers with Light Sensing Properties

2017 ◽  
Vol 54 (4) ◽  
pp. 655-658
Author(s):  
Andrei Bejan ◽  
Dragos Peptanariu ◽  
Bogdan Chiricuta ◽  
Elena Bicu ◽  
Dalila Belei
Keyword(s):  
Molecular Weight ◽  
Low Molecular Weight ◽  
X Ray Diffraction ◽  
Aromatic Rings ◽  
X Ray ◽  
Force Microscopy ◽  
Light Sensing ◽  
Sensing Applications ◽  
Atomic Force ◽  
Low Molecular Weight Compounds

Microfibers were obtained from organic low molecular weight compounds based on heteroaromatic and aromatic rings connected by aliphatic spacers. The obtaining of microfibers was proved by scanning electron microscopy. The deciphering of the mechanism of microfiber formation has been elucidated by X-ray diffraction, infrared spectroscopy, and atomic force microscopy measurements. By exciting with light of different wavelength, florescence microscopy revealed a specific optical response, recommending these materials for light sensing applications.

Characteristics of Electron Transport Study of Composited Graphene-Zinc Oxide Thin Film Photoanode for Dye-Sensitized Solar Cells

2020 ◽  
Vol 307 ◽  
pp. 185-191
Author(s):  
Noor Syafiqah Samsi ◽  
N.A.S. Affendi ◽  
M.K. Yaakob ◽  
M.F.M. Taib ◽  
A. Lepit ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Dye Sensitized Solar Cells ◽  
Xrd Analysis ◽  
Oxide Thin Film ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Zno Nanosheets ◽  
High Degree ◽  
Sensitized Solar Cells

Graphene-Zinc Oxide (Gr-ZnO) nanocomposites films were successfully synthesized via facile electrodeposition method in an aqueous solution under Gr concentration conditions. Gr, as a highly conductive carbon, acts as an anchor for ZnO nanosheets and plays a substantial role in controlling the degree of dispersion of ZnO nanosheets onto indium-doped tin oxide (ITO) substrate to form Gr-ZnO nanocomposite. Atomic force microscopy (AFM) and field-emission scanning electron microscopy (FESEM) analysis of Gr-ZnO nanocomposite samples confirmed that the presence of ZnO nanosheets with a high degree of dispersity and crystallinity which is well linked to the thin layer of Gr nanoparticle on ITO substrate. The surface roughness of the films found increased to ~270 nm on Gr-ZnO as compared to Gr ~44 nm and ZnO ~3 nm. Further, the x-ray diffraction spectroscopy (XRD) analysis showed the result is in good agreement with Raman spectroscopy study. The cyclic voltammetry (CV) of Gr-ZnO nanocomposite revealed that the effect of electron-hole recombination process was increased and the presence of Gr in ZnO photoanode provides the fastest redox reaction and hence offers the fastest electron transfer in photoanode.

scholarly journals Nanoporous Sodium Carboxymethyl Cellulose-g-poly (Sodium Acrylate)/FeCl3 Hydrogel Beads: Synthesis and Characterization

Gels ◽  
2020 ◽  
Vol 6 (4) ◽  
pp. 49
Author(s):  
Bijender Kumar ◽  
Ruchir Priyadarshi ◽  
Sauraj ◽  
Farha Deeba ◽  
Anurag Kulshreshtha ◽  
...  
Keyword(s):  
Carboxymethyl Cellulose ◽  
Sodium Carboxymethyl Cellulose ◽  
Sodium Acrylate ◽  
X Ray Diffraction ◽  
Hybrid Hydrogel ◽  
X Ray ◽  
Hydrogel Beads ◽  
Force Microscopy ◽  
Atomic Force ◽  
Potential Applications

Novel sodium carboxymethyl cellulose-g-poly (sodium acrylate)/Ferric chloride (CMC-g-PNaA/FeCl3) nanoporous hydrogel beads were prepared based on the ionic cross-linking between CMC-g-PNaA and FeCl3. The structure of CMC and CMC-g-PNaA were elucidated by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) spectroscopy, and the elemental composition was analyzed by energy dispersive X-ray analysis (EDX). The physicochemical properties of the CMC-g-PNaA/FeCl3 hydrogel beads were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and thermogravimetric analysis (TGA). The swelling percentage of hydrogel beads was studied at different time periods. The obtained CMC-g-PNaA/FeCl3 hydrogel beads exhibited a higher nanoporous morphology than those of CMC-g-PNaA and CMC beads. Furthermore, an AFM image of the CMC-g-PNaA/FeCl3 beads shows granule type topology. Compared to the CMC-g-PNaA (189 °C), CMC-g-PNaA/FeCl3 hydrogel beads exhibited improvement in thermal stability (199 °C). Furthermore, CMC-g-PNaA/FeCl3 hydrogel beads depicted a higher swelling percentage capacity of around 1452%, as compared to CMC-g-PNaA (1096%). Moreover, this strategy with preliminary results could be useful for the development of polysaccharide-based hybrid hydrogel beads for various potential applications.

Facile synthesis of TiO2 film on glass for the photocatalytic removal of rhodamine B and tetracycline hydrochloride

2019 ◽  
Vol 9 (5) ◽  
pp. 437-443 ◽  
Author(s):  
Jiaxin Li ◽  
Zhi Chen ◽  
Jianfei Fang ◽  
Qian Yang ◽  
Xiuru Yang ◽  
...  
Keyword(s):  
Thin Film ◽  
Organic Pollutants ◽  
Reaction System ◽  
Practical Application ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Photocatalytic Removal ◽  
Coating Method ◽  
Potential Applications

Photocatalysis is one of the efficient approaches for pollution control in water. However, the traditional photocatalysts used for the removal of organic pollutants are in powder form, which makes it difficult to recover them from the suspended reaction system. On the contrary, thin film photocatalyst is easy to be retrieved and possesses unique feature for practical application. In present work, stable TiO2 sol suspension was prepared and amorphous TiO2 thin film was then immobilized upon glass substrate through facile spin coating method. The thickness of film could be simply controlled by changing the number of coatings, and anatase TiO2 film could be formed after calcination. The prepared thin films were characterized with X-ray diffraction (XRD), ultravioletvisible spectrophotometry (UV-vis), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The photodegradations of organic pollutants including colored dye and colorless antibiotic were tested and found to be thickness-dependent. Additionally, the prepared film photocatalst has good stability and may have potential applications in wastewater treatment.

Magnetron Sputtering of Tantalum Oxide Thin Electrolyte Film for Electrochromic Applications

2012 ◽  
Vol 512-515 ◽  
pp. 1604-1608 ◽  
Author(s):  
Chien Cheng Liu ◽  
Kuang I Liu ◽  
Hao Tung Lin ◽  
Jow Lay Huang
Keyword(s):  
Magnetron Sputtering ◽  
Tantalum Oxide ◽  
Conducting Layer ◽  
Electrochromic Property ◽  
X Ray Diffraction ◽  
Atomic Force ◽  
Electrolyte Film ◽  
Potential Applications ◽  
Uv Visible ◽  
Ion Conducting

Electrochromism have been widely investigated due to their potential applications such as automobile and building window. In this study, tantalum oxide thin films used as ion conducting layer were deposited on WO3/ITO at room temperature by magnetron sputtering. The thickness of tantalum oxide films were varied to investigate their effects on composition, microstructure, optical properties, and electrochromic properties determined by X-ray diffraction, UV-visible spectrometer, Atomic force microscope (AFM), and field-emission scanning electron microscope (FE-SEM). Experimental results indicated Ta2O5at thickness of 300 nm with low packing density were favorable for ions transmission deposited on WO3/ITO had better electrochromic property.

GROWTH OF SPUTTERED-ALUMINUM OXIDE THIN FILMS ON Si (100) AND Si (111) SUBSTRATES WITH Al2O3 BUFFER LAYER

2016 ◽  
Vol 23 (03) ◽  
pp. 1650016
Author(s):  
WEI QIANG LIM ◽  
SUBRAMANI SHANMUGAN ◽  
MUTHARASU DEVARAJAN
Keyword(s):  
Thin Films ◽  
Aluminum Oxide ◽  
Buffer Layer ◽  
Annealing Temperature ◽  
Rf Magnetron Sputtering ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Si Substrates ◽  
Atomic Force ◽  
Section Analysis

Aluminum oxide (Al2O3) thin films with Al2O3 buffer layer were deposited on Si (100) and Si (111) substrates using RF magnetron sputtering of Al2O3 target in Ar atmosphere. The synthesized films were then annealed at the temperature of 400[Formula: see text]C, 600[Formula: see text]C and 800[Formula: see text]C in nitrogen (N2) environment for 6[Formula: see text]h. Structural properties and surface morphology are examined by using X-Ray Diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM) and Atomic Force Microscope (AFM). XRD analysis indicated that different orientation of Al2O3 were formed with different intensities due to increase in the annealing temperature. From FESEM cross-section analysis results, it is observed that the thickness of films were increased as the annealing temperature increased. EDX analysis shows that the concentration of aluminum and oxygen on both the Si substrates increased with the increase in annealing temperature. The surface roughness of the films were found to be decreased first when the annealing temperature is increased to 400[Formula: see text]C, yet the roughness increased when the annealing temperature is further increased to 800[Formula: see text]C.

scholarly journals Laser Ablation Ceramic Target for 8YSZ High-k Dielectric Electrolyte thin Films Precessed by PLD on Si(100) and Pt/Si(111)

2020 ◽  
Vol 71 (7) ◽  
pp. 272-277
Author(s):  
Rovena Veronica Pascu
Keyword(s):  
Thin Films ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
High K ◽  
Potential Applications ◽  
Electrochemical Devices ◽  
High K Dielectric

The cubic structure 8YSZ (8%Yttria-Stabilized Zirconia) thin films deposited by PLD(Pulsed Laser Deposition) on substrates Si (100) and Pt/Si (111) by identical control parameters have potential applications as electrolytes for planar micro electrochemical devices like Lambda oxygen sensors and IT-�SOFC. It appearance differences in polycrystalline structural and optical characterization by XRD (X-ray Diffraction), SEM (Scanning Electron Microscope), AFM (Atomic Force Microscopy) and V- VASE (Variable Angle Spectroscopic Ellipsometry. The differences are relating on crystalline dimensions, lattice parameters; surface roughness measured by V- VASE and AFM are presented synthetic to evidence the differences generated by substrates.

HUMIDITY AND TEMPERATURE DEPENDENT CHARACTERISTICS OF Ag/SnNcCl2/Ag SURFACE TYPE MULTIFUNCTIONAL SENSOR

2019 ◽  
Vol 27 (05) ◽  
pp. 1950148
Author(s):  
ABDUL WAJID ◽  
MUHAMMAD TAHIR ◽  
ARIF ◽  
SAYYED IZAZ UDDIN ◽  
FAZAL WAHAB
Keyword(s):  
Amorphous Structure ◽  
Temperature Sensing ◽  
Electrode Gap ◽  
Surface Type ◽  
Sensing Applications ◽  
Atomic Force ◽  
Ag Electrodes ◽  
Vis Spectroscopy ◽  
Humidity Measurements ◽  
Relative Humidity Range

In this work, the potential of tin (IV) 2,3-napthalocyanine dichloride (SnNcCl2) has been studied for sensing applications due to its hydrophobic nature. The multipurpose sensor was fabricated by depositing 50-nm silver (Ag) electrodes on a glass substrate through vacuum thermal evaporation at pressure of [Formula: see text] mbar. With the help of masking, a 40-micron inter-electrode gap between Ag electrodes was developed and then 80-nm film of SnNcCl2 was thermally deposited in the inter-electrode gap resulting in a surface type Ag/SnNcCl2/Ag multipurpose sensor and was studied for humidity and temperature sensing. The humidity characterization was carried out at two different frequencies, i.e. 120 and 1[Formula: see text]kHz in the relative humidity range 35–85% RH and 5.5 and 1.3 times increase was recorded with respect to initial capacitance for both frequencies, respectively. The temperature sensing was studied within a temperature range of 15–80∘C at 120[Formula: see text]Hz frequency and 1.3 times increase in capacitance was observed with respect to initial capacitance. The sensor’s important parameters, i.e. response time and recovery time were measured to be 8 and 3[Formula: see text]s at 120[Formula: see text]Hz for humidity measurements. The morphology of the SnNcCl2 thin film was measured by atomic force microscope (AFM) and scanning electron microscope (SEM) showing rough surface favorable for sensing applications. The amorphous structure of the film was confirmed by X-ray diffraction (XRD) while optical bandgap was calculated from ultraviolet-visible (UV-vis) spectroscopy.

Microstructural features and mechanical properties of 18 MeV He+ ions irradiated pure Zr

2016 ◽  
Vol 30 (32n33) ◽  
pp. 1650395
Author(s):  
Mohsin Rafique ◽  
San Chae ◽  
Yong-Soo Kim
Keyword(s):  
Grain Size ◽  
Irradiation Dose ◽  
Dose Range ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Pure Zirconium ◽  
Higher Doses

Samples of pure zirconium (Zr) were irradiated by 18 MeV helium (He[Formula: see text]) ions in the dose range 0.00162–0.0324 dpa at 373 K by using Cyclotron accelerator. The atomic force microscopy (AFM) results indicated an increase in average surface roughness of Zr by increasing the irradiation dose. The AFM images revealed nucleation and growth of nano- and micro-size hillocks at lower doses (0.00162–0.00324 dpa), whereas formation of a volcano-like cavities and craters was observed within these hillocks by increasing the radiation dose from 0.00324 to 0.0324 dpa. The high-resolution X-ray diffraction (XRD) results showed a variation in the intensities and positions of the diffraction peaks after the irradiation. The transmission electron microscopy (TEM) results reported a significant decrease in the grain size after the He[Formula: see text] irradiation. The values of grain size, calculated using the TEM, were found to be in good agreement with the crystallite size calculated using the XRD analysis. The yield stress (YS) was increased by increasing the irradiation dose up to 0.0162 dpa, however, the YS exhibited a decreasing trend with a further increase of the dose. The changes in YS were elucidated by grain size reduction and localized heating at higher doses.

scholarly journals Tribo-Mechanical Properties of the Antimicrobial Low-Density Polyethylene (LDPE) Nanocomposite with Hybrid ZnO–Vermiculite–Chlorhexidine Nanofillers

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2811
Author(s):  
Karla Čech Barabaszová ◽  
Sylva Holešová ◽  
Marianna Hundáková ◽  
Alena Kalendová
Keyword(s):  
Mechanical Properties ◽  
Zinc Oxide ◽  
Xrd Analysis ◽  
Surface Topology ◽  
Low Density Polyethylene ◽  
Indentation Hardness ◽  
Low Density ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force

Materials made from low-density polyethylene (LDPE) in the form of packages or catheters are currently commonly applied medical devices. Antimicrobial LDPE nanocomposite materials with two types of nanofillers, zinc oxide/vermiculite (ZnO/V) and zinc oxide/vermiculite_chlorhexidine (ZnO/V_CH), were prepared by a melt-compounded procedure to enrich their controllable antimicrobial, microstructural, topographical and tribo-mechanical properties. X-ray diffraction (XRD) analysis and Fourier transform infrared spectroscopy (FTIR) revealed that the ZnO/V and ZnO/V_CH nanofillers and LDPE interacted well with each other. The influence of the nanofiller concentrations on the LDPE nanocomposite surface changes was studied through scanning electron microscopy (SEM), and the surface topology and roughness were studied using atomic force microscopy (AFM). The effect of the ZnO/V nanofiller on the increase in indentation hardness (HIT) was evaluated by AFM measurements and the Vickers microhardness (HV), which showed that as the concentration of the ZnO/V nanofiller increased, these values decreased. The ZnO/V and ZnO/V_CH nanofillers, regardless of the concentration in the LDPE matrix, slightly increased the average values of the friction coefficient (COF). The abrasion depths of the wear indicated that the LDPE_ZnO/V nanocomposite plates exhibited better wear resistance than LDPE_ZnO/V_CH. Higher HV and HIT microhardness values were measured for both nanofillers than the natural LDPE nanocomposite plate. Very positive antimicrobial activity against S. aureus and P. aeruginosa after 72 h was found for both nanofiller types.

Sign in / Sign up

Export Citation Format

Share Document