scholarly journals Investigation of a Short Carbon Fibre-Reinforced Polyamide and Comparison of Two Manufacturing Processes: Fused Deposition Modelling (FDM) and Polymer Injection Moulding (PIM)

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 672 ◽  
Author(s):  
Elena Verdejo de Toro ◽  
Juana Coello Sobrino ◽  
Alberto Martínez Martínez ◽  
Valentín Miguel Eguía ◽  
Jorge Ayllón Pérez
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Injection Moulding ◽  
New Technologies ◽  
Mechanical Response ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Polymer Injection ◽  
Fused Deposition

New technologies are offering progressively more effective alternatives to traditional ones. Additive Manufacturing (AM) is gaining importance in fields related to design, manufacturing, engineering and medicine, especially in applications which require complex geometries. Fused Deposition Modelling (FDM) is framed within AM as a technology in which, due to their layer-by-layer deposition, thermoplastic polymers are used for manufacturing parts with a high degree of accuracy and minimum material waste during the process. The traditional technology corresponding to FDM is Polymer Injection Moulding, in which polymeric pellets are injected by pressure into a mould using the required geometry. The increasing use of PA6 in Additive Manufacturing makes it necessary to study the possibility of replacing certain parts manufactured by injection moulding with those created using FDM. In this work, PA6 was selected due to its higher mechanical properties in comparison with PA12. Moreover, its higher melting point has been a limitation for 3D printing technology, and a further study of composites made of PA6 using 3D printing processes is needed. Nevertheless, analysis of the mechanical response of standardised samples and the influence of the manufacturing process on the polyamide’s mechanical properties needs to be carried out. In this work, a comparative study between the two processes was conducted, and conclusions were drawn from an engineering perspective.

scholarly journals Parameters Affecting the Mechanical Properties of Three-Dimensional (3D) Printed Carbon Fiber-Reinforced Polylactide Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2456
Author(s):  
Demei Lee ◽  
Guan-Yu Wu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Bed Temperature ◽  
3D Printed ◽  
The Impact

Three-dimensional (3D) printing is a manufacturing technology which creates three-dimensional objects layer-by-layer or drop-by-drop with minimal material waste. Despite the fact that 3D printing is a versatile and adaptable process and has advantages in establishing complex and net-shaped structures over conventional manufacturing methods, the challenge remains in identifying the optimal parameters for the 3D printing process. This study investigated the influence of processing parameters on the mechanical properties of Fused Deposition Modelling (FDM)-printed carbon fiber-filled polylactide (CFR-PLA) composites by employing an orthogonal array model. After printing, the tensile and impact strengths of the printed composites were measured, and the effects of different parameters on these strengths were examined. The experimental results indicate that 3D-printed CFR-PLA showed a rougher surface morphology than virgin PLA. For the variables selected in this analysis, bed temperature was identified as the most influential parameter on the tensile strength of CFR-PLA-printed parts, while bed temperature and print orientation were the key parameters affecting the impact strengths of printed composites. The 45° orientation printed parts also showed superior mechanical strengths than the 90° printed parts.

Effects of processing conditions on mechanical properties of PLA printed parts

2019 ◽  
Vol 26 (2) ◽  
pp. 381-389
Author(s):  
Morteza Behzadnasab ◽  
Ali Akbar Yousefi ◽  
Dariush Ebrahimibagha ◽  
Farahnaz Nasiri
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Physical And Mechanical Properties ◽  
Fused Deposition Modelling ◽  
Temperature Pattern ◽  
Layer By Layer ◽  
Processing Conditions ◽  
Content Type ◽  
Fused Deposition

Purpose With recent advances in additive manufacturing (AM), polymer-based three-dimensional (3D) printers are available for relatively low cost and have found their way even in domestic and educational uses. However, the optimum conditions for processing and post-processing of different materials are yet to be determined. The purpose of this paper is to examine the effects of printing temperature, pattern and annealing conditions on tensile strength and modulus of samples printed with polylactic acid (PLA). Design/methodology/approach This study focuses on fused deposition modelling according to ISO/ASTM 52900 material extrusion AM. To print parts with maximum mechanical properties, the printing variables must be optimised. To determine the printing and annealing condition on physical and mechanical properties of PLA-based parts, dogbone-shaped tensile samples were printed at four different nozzle temperatures and five different filling patterns embedded in a 3D printing software. The samples were further annealed at three different temperatures for three different time intervals. The mechanical properties were evaluated and the changes in mechanical properties were analysed with the help of rheometrical measurements. Findings The results showed that printing condition has a significant influence on final properties, for example, the strain at break value increases with increasing nozzle temperature from 34 to 56 MPa, which is close to the value of the injected sample, namely, 65 MPa. While tensile strength increases with printing temperature, the annealing process has negative effects on the mechanical properties of samples. Originality/value The authors observed that traditional findings in polymer science, for example, the relationship between processing and annealing temperature, must be re-evaluated when applied in 3D printing because of major differences in processing conditions resulting from the layer-by-layer manufacturing.

Mechanical Properties of Diamond Schwarzites: From Atomistic Models to 3D-Printed Structures

MRS Advances ◽  
2020 ◽  
Vol 5 (33-34) ◽  
pp. 1775-1781 ◽  
Author(s):  
Levi C. Felix ◽  
Vladimir Gaál ◽  
Cristiano F. Woellner ◽  
Varlei Rodrigues ◽  
Douglas S. Galvao
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Uniaxial Compression ◽  
Chemical Vapour ◽  
Md Simulations ◽  
Atomic Model ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Structural Applications ◽  
3D Printed

ABSTRACTTriply Periodic Minimal Surfaces (TPMS) possess locally minimized surface area under the constraint of periodic boundary conditions. Different families of surfaces were obtained with different topologies satisfying such conditions. Examples of such families include Primitive (P), Gyroid (G) and Diamond (D) surfaces. From a purely mathematical subject, TPMS have been recently found in materials science as optimal geometries for structural applications. Proposed by Mackay and Terrones in 1991, schwarzites are 3D crystalline porous carbon nanocrystals exhibiting a TPMS-like surface topology. Although their complex topology poses serious limitations on their synthesis with conventional nanoscale fabrication methods, such as Chemical Vapour Deposition (CVD), schwarzites can be fabricated by Additive Manufacturing (AM) techniques, such as 3D Printing. In this work, we used an optimized atomic model of a schwarzite structure from the D family (D8bal) to generate a surface mesh that was subsequently used for 3D-printing through Fused Deposition Modelling (FDM). This D schwarzite was 3D-printed with thermoplastic PolyLactic Acid (PLA) polymer filaments. Mechanical properties under uniaxial compression were investigated for both the atomic model and the 3D-printed one. Fully atomistic Molecular Dynamics (MD) simulations were also carried out to investigate the uniaxial compression behavior of the D8bal atomic model. Mechanical testings were performed on the 3D-printed schwarzite where the deformation mechanisms were found to be similar to those observed in MD simulations. These results are suggestive of a scale-independent mechanical behavior that is dominated by structural topology.

scholarly journals Biogenic Composite Filaments Based on Polylactide and Diatomaceous Earth for 3D Printing

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4632
Author(s):  
Marta Dobrosielska ◽  
Robert Przekop ◽  
Bogna Sztorch ◽  
Dariusz Brząkalski ◽  
Izabela Zgłobicka ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Filler Particle ◽  
Fused Deposition Modelling ◽  
Water Contact ◽  
Rheological Analysis ◽  
Fused Deposition ◽  
Filler Particle Size ◽  
Composite Properties

New composites containing a natural filler made of diatom shells (frustules), permitting the modification of polylactide matrix, were produced by Fused Deposition Modelling (3D printing) and were thoroughly examined. Two mesh fractions of the filler were used, one of <40 µm and the other of 40−63 µm, in order to check the effect of the filler particle size on the composite properties. The composites obtained contained diatom shells in the concentrations from 0% to 5% wt. (0−27.5% vol.) and were subjected to rheological analysis. The composites obtained as filaments of 1.75 mm in diameter were used for 3D printing. The printed samples were characterized as to hydrophilic–hydrophobic, thermal and mechanical properties. The functional parameters of the printed objects, e.g., mechanical characteristics, stability on contact with water and water contact angle, were measured. The results revealed differences in the processing behavior of the samples as well as the effect of secondary granulation of the filler on the parameters of the printing and mechanical properties of the composites.

scholarly journals Analisis Proses 3D Printing terhadap Pengujian Impak Metode Charpy Pada Material PLA+

2021 ◽  
Vol 2 (8) ◽  
pp. 1480-1493
Author(s):  
Ilham Akbar ◽  
Zaldy Sirwansyah Suzen ◽  
Idiar Idiar
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Melting Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Cooling Speed ◽  
Nozzle Temperature

Pada era industri perkembangan teknologi pada saat ini telah mengalami kemajuan yang sangat pesat, salah satunya adalah teknologi 3D printing atau juga dikenal sebagai additive manufacturing. Salah satu teknologi 3D printing yang terkenal adalah Fused Deposition Modelling (FDM). Prinsip kerja FDM adalah dengan cara ekstrusi termoplastik melalui nozzle yang panas pada melting temperature selanjutnya produk dibuat lapis perlapis. Teknologi 3D printing adalah proses pembuatan benda padat dari sebuah file digital. Penelitian ini menggunakan metode eksperimen, dilakukan pada mesin 3D printing FDM model Prusa area dengan menggunakan nozzle 0,4mm. Material yang digunakan adalah filamen PLA+ dengan diameter 1,75mm variasi parameternya nozzle temperature (205oC, 215oC, 225oC), Cooling speed (100%, 90%, 80%), infill type (grid, lines, triangles, Tri hexagon, cubic, cubic subdivision, octet, quarter qubic, concentric, zigzag, cross, cross 3D dan gyroid). Penelitian ini menggunakan 39 sampel dengan tujuan untuk mengetahui hasil uji impak tertinggi dan terendah dengan pengujian impak dari parameter yang ditentukan yaitu orientasi printing 90o. Hasil dari pengujian impak tertinggi sebesar 0,00548 Joule/mm2 dengan ekperimen nomor 32 infill geometry (cubic Subdivision), cooling speed 80% dan nozzle temperature 225ºC. Sedangkan nilai uji impak terendah sebesar 0,00084 Joule/mm2 dengan ekperimen nomor 14 dan 17 infill geometry (grid) dan (Tri hexagon), cooling speed 90%, nozzle temperature 215ºC dan ekperimen nomor 27 infill geometry grid, cooling speed 80%, nozzle temperature 225ºC. hasil pengujian impak menggunakan spesimen PLA+ didapatkan nilai uji impak sebesar 0,00548 Joule/mm2, dengan ekperimen nomor 32 infill geometry cubic subdivision, cooling speed 80%, nozzle temperature 225oC.

Investigating the Mechanical Behavior of 3D Printed PLA-Coco Coir Composites

2021 ◽  
Vol 1046 ◽  
pp. 125-132
Author(s):  
Paul Eric C. Maglalang ◽  
Blessie A. Basilia ◽  
Araceli Magsino Monsada
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
3D Printing ◽  
Fused Deposition Modelling ◽  
Coir Fiber ◽  
Fiber Concentration ◽  
Fused Deposition ◽  
Twin Screw ◽  
Raster Angle ◽  
Composite Filament

It is quite amazing that the use of 3D printing techniques, especially the Fused Deposition Modelling (FDM) has delivered such significance in terms of cost reduction, time saver features where a different variety of thermoplastic and composite materials (Biodegradable and Non-biodegradable) are well developed. Different sectors have continually developed natural organic materials that are also both structurally composite in nature. Similarly, the use of different fibers that are abundantly accessible and considered as renewable resources which can be optionally combined with other biodegradable materials is a great challenge through the use of the FDM printing method. The study aims to determine the effect of different particle size and raster angle at a certain fiber concentration which could affect the mechanical properties of the composite by developing a printable composite filament made of Polylactic Acid (PLA) and Coco Coir materials using a filament maker and FDM printer. The composite filament was fabricated and optimized using a twin-screw extruder and 3D Devo Filament maker. 3D printing of samples for mechanical testing was conducted using three (3) raster angles (45o, 60o, and 75o) and various particle sizes of coco coir fiber reinforcement in the PLA matrix. Results showed that the < 74μm particle size of the coco-coir exhibited a 24% and 175% increase in tensile strength and izod impact strength compared to the pure PLA at 60o and 75o raster angles, respectively. Likewise, the reinforcement of <149μm particle size coco coir at 45o raster angle contributes to an increase of 4.8% flexural and 176% compressive strength compared to pure PLA. The study concludes that there is an improvement in the mechanical properties of the PLA-Coco Coir composite at a certain particle size and raster angle in 3D printing.

3D Printing: Basic Concepts Mathematics and Technologies

2013 ◽  
Vol 2 (2) ◽  
pp. 58-71
Author(s):  
Alexander Rompas ◽  
Charalampos Tsirmpas ◽  
Ianos Papatheodorou ◽  
Georgia Koutsouri ◽  
Dimitris Koutsouris
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Real Life ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Three Dimensional Objects ◽  
Stl File ◽  
Fused Deposition ◽  
3D Printers ◽  
Object Layer

3D printing is about being able to print any object layer by layer. But if one questions this proposition, can one find any three-dimensional objects that can't be printed layer by layer? To banish any disbeliefs the authors walked together through the mathematics that prove 3d printing is feasible for any real life object. 3d printers create three-dimensional objects by building them up layer by layer. The current generation of 3d printers typically requires input from a CAD program in the form of an STL file, which defines a shape by a list of triangle vertices. The vast majority of 3d printers use two techniques, FDM (Fused Deposition Modelling) and PBP (Powder Binder Printing). One advanced form of 3d printing that has been an area of increasing scientific interest the recent years is bioprinting. Cell printers utilizing techniques similar to FDM were developed for bioprinting. These printers give us the ability to place cells in positions that mimic their respective positions in organs. Finally, through a series of case studies the authors show that 3d printers have made a massive breakthrough in medicine lately.

scholarly journals Research and Implementation of Axial 3D Printing Method for PLA Pipes

2020 ◽  
Vol 10 (13) ◽  
pp. 4680
Author(s):  
Haiguang Zhang ◽  
Wenguang Zhong ◽  
Qingxi Hu ◽  
Mohamed Aburaia ◽  
Joamin Gonzalez-Gutierrez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Layer By Layer ◽  
Standard Material ◽  
Material Extrusion ◽  
G Code ◽  
Realization Process ◽  
Actual Stress ◽  
Printing Method

Additive manufacturing has been applied in many fields, but its layer-by-layer fabrication process leads to a weak inter-layer bond strength of printed parts, so it cannot meet the higher requirements for mechanical properties of the industry. At present, many researchers are studying the printing path planning method to improve the mechanical properties of printed parts. This paper proposes a method to plan the printing path according to the actual stress of pipe parts, and introduces the realization process of an algorithm in detail, and obtains the printing control G-code. Additionally, a 5-axis material extrusion platform was built to realize the printing of polylactic acid pipes with plane and space skeleton curves, respectively, which verified the feasibility and applicability of the method and the correctness of the planning path with standard material extrusion filaments. Finally, the tensile and bending experiments prove that axial printing enhances the mechanical properties of pipe parts.

Sign in / Sign up

Export Citation Format

Share Document