scholarly journals Influence of Ti on the Tensile Properties of the High-Strength Powder Metallurgy High Entropy Alloys

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 578 ◽  
Author(s):  
Igor Moravcik ◽  
Stepan Gamanov ◽  
Larissa Moravcikova-Gouvea ◽  
Zuzana Kovacova ◽  
Michael Kitzmantel ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Tensile Properties ◽  
High Strength ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Solid Solution Strengthening ◽  
Plasma Sintering ◽  
Annealing Heat Treatment ◽  
Face Centered

The focus of this study is the evaluation of the influence of Ti concentration on the tensile properties of powder metallurgy high entropy alloys. Three Ni1.5Co1.5CrFeTiX alloys with X = 0.3; 0.5 and 0.7 were produced by mechanical alloying and spark plasma sintering. Additional annealing heat treatment at 1100 °C was utilized to obtain homogenous single-phase face centered cubic (FCC) microstructures, with minor oxide inclusions. The results show that Ti increases the strength of the alloys by increasing the average atomic size misfit i.e., solid solution strengthening. An excellent combination of mechanical properties can be obtained by the proposed method. For instance, annealed Ni1,5Co1,5CrFeTi0.7 alloy possessed the ultimate tensile strength as high as ~1600 MPa at a tensile ductility of ~9%, despite the oxide contamination. The presented results may serve as a guideline for future alloy design of novel, inclusion-tolerant materials for sustainable metallurgy.

scholarly journals Tailoring Compressive Strength and Absorption Energy of Lightweight Multi-Phase AlCuSiFeX (X = Cr, Mn, Zn, Sn) High-Entropy Alloys Processed via Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4945
Author(s):  
Ashutosh Sharma ◽  
Hansung Lee ◽  
Byungmin Ahn
Keyword(s):  
Powder Metallurgy ◽  
Low Cost ◽  
High Strength ◽  
Fracture Mechanisms ◽  
Solid Solution Phase ◽  
Face Centered Cubic ◽  
Σ Phase ◽  
High Entropy ◽  
Face Centered ◽  
Fcc Phase

The development of lightweight HEAs with high strength and low cost is an urgent requirement. In this study, equimolar AlCuSiFeX (X = Cr, Mn, Zn, Sn) lightweight HEAs were fabricated by advanced powder metallurgy. The mechanical alloying was performed for 45 h, and the powder compacts were densified at 650 °C. The final results revealed that AlCuSiFeSn lightweight HEA was composed of a single face-centered cubic (FCC) and Cu81Sn22, whereas AlCuSiFeZn showed a dual FCC and body-centered cubic (BCC) structures. Similarly, AlCuSiFeMn alloy contained a BCC + FCC phase with a µ-phase, whereas a σ-phase was present in AlCuSiFeCr in addition to FCC + BCC phases. We also calculated various thermodynamic parameters to predict the solid-solution phase stability of each of the above lightweight HEAs. It was found that lightweight HEAs with additive elements Sn and Zn tend to predominant FCC phases, whereas those with Cr and Mn result in major BCC with hard µ and σ phases, which further improve their mechanical strength. A maximum fracture strain of 23% was obtained for AlCuSiFeSn followed by 19% for AlCuSiFeZn HEA. The compressive fracture mechanisms of these lightweight HEAs are also discussed and reported here.

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

scholarly journals Effects of Different Contents of Each Component on the Structural Stability and Mechanical Properties of Co-Cr-Fe-Ni High-Entropy Alloys

2021 ◽  
Vol 11 (6) ◽  
pp. 2832
Author(s):  
Haibo Liu ◽  
Cunlin Xin ◽  
Lei Liu ◽  
Chunqiang Zhuang
Keyword(s):  
Mechanical Properties ◽  
Structural Stability ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
Obvious Effect ◽  
High Entropy ◽  
Precise Control ◽  
Component Content ◽  
Face Centered ◽  
And Performance

The structural stability of high-entropy alloys (HEAs) is closely related to their mechanical properties. The precise control of the component content is a key step toward understanding their structural stability and further determining their mechanical properties. In this study, first-principle calculations were performed to investigate the effects of different contents of each component on the structural stability and mechanical properties of Co-Cr-Fe-Ni HEAs based on the supercell model. Co-Cr-Fe-Ni HEAs were constructed based on a single face-centered cubic (FCC) solid solution. Elemental components have a clear effect on their structure and performance; the Cr and Fe elements have an obvious effect on the structural stability and equilibrium lattice constant, respectively. The Ni elements have an obvious effect on stiffness. The Pugh ratios indicate that Cr and Ni addition may increase ductility, whereas Co and Fe addition may decrease it. With increasing Co and Fe contents or decreasing Cr and Ni contents, the structural stability and stiffness of Co-Cr-Fe-Ni HEAs are improved. The structural stability and mechanical properties may be related to the strength of the metallic bonding and covalent bonding inside Co-Cr-Fe-Ni HEAs, which, in turn, is determined by the change in element content. Our results provide the underlying insights needed to guide the optimization of Co-Cr-Fe-Ni HEAs with excellent mechanical properties.

Insights into Defect-Mediated Nucleation of Equilibrium B2 Phase in Face-Centered Cubic High-Entropy Alloys

JOM ◽  
2021 ◽  
Author(s):  
Abhishek Sharma ◽  
Bharat Gwalani ◽  
Sriswaroop Dasari ◽  
Deep Choudhuri ◽  
Yao-Jen Chang ◽  
...  
Keyword(s):  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
B2 Phase ◽  
Face Centered

Bimodality of incipient plastic strength in face-centered cubic high-entropy alloys

2021 ◽  
Vol 202 ◽  
pp. 124-134
Author(s):  
Yakai Zhao ◽  
Jeong-Min Park ◽  
Jae-il Jang ◽  
Upadrasta Ramamurty
Keyword(s):  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plastic Strength ◽  
Face Centered

Compression stress strengthening modelling of a ultrafine-grained equiatomic SPS CoCrFeNiNb high-entropy alloy

2020 ◽  
pp. 095440622094324
Author(s):  
Marcello Cabibbo ◽  
Filip Průša ◽  
Alexandra Šenková ◽  
Andrea Školáková ◽  
Vojtěch Kučera ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Mechanical Alloying ◽  
Oxide Phase ◽  
High Entropy Alloy ◽  
Induction Melting ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

High-entropy alloys are known to show exceptionally high mechanical properties, both compression and tensile strength, and unique physical properties, such as their phase stability. These quite unusual properties are primarily due to the microstructure generated by mechanical alloying processes, such as conventional induction arc melting, powder metallurgy, or mechanical alloying. In the present study, an equiatomic CoCrFeNiNb high-entropy alloy was prepared by a sequence of conventional induction melting, powder metallurgy, and compaction via spark plasma sintering. The high-entropy alloys showed uniform sub-micrometer grain microstructure consisted by a mixture of an fcc solid solution strengthened by a hcp Laves phase and a third intergranular oxide phase. The as-cast high-entropy alloys showed an ultimate compression strength (UCS) of ∼1400 MPa, which after sintering and compaction at 1273 K increased up to ∼2400 MPa. Extensive transmission electron microscopy quantitative analyses were carried out to model the UCS. A quite good agreement between the microstructure-strengthening model and the experimental UCS was found.

Effects of Mn Content and Grain Size on Hydrogen Embrittlement Susceptibility of Face-Centered Cubic High-Entropy Alloys

2020 ◽  
Vol 51 (11) ◽  
pp. 5612-5616
Author(s):  
Motomichi Koyama ◽  
Haoyu Wang ◽  
Virendra Kumar Verma ◽  
Kaneaki Tsuzaki ◽  
Eiji Akiyama
Keyword(s):  
Grain Size ◽  
Hydrogen Embrittlement ◽  
High Entropy Alloys ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Mn Content ◽  
Face Centered
Sign in / Sign up

Export Citation Format

Share Document