scholarly journals Improvement of Mechanical Properties of Plasma Sprayed Al2O3-ZrO2-SiO2 Amorphous Coatings by Surface Crystallization

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3232 ◽  
Author(s):  
Jan Medricky ◽  
Frantisek Lukac ◽  
Stefan Csaki ◽  
Sarka Houdkova ◽  
Maria Barbosa ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Wear Resistance ◽  
Large Scale ◽  
Mechanical Response ◽  
High Energy ◽  
Hardness Profile ◽  
Treatment Conditions ◽  
Content Ratio ◽  
Plasma Sprayed

Ceramic Al2O3-ZrO2-SiO2 coatings with near eutectic composition were plasma sprayed using hybrid water stabilized plasma torch (WSP-H). The as-sprayed coatings possessed fully amorphous microstructure which can be transformed to nanocrystalline by further heat treatment. The amorphous/crystalline content ratio and the crystallite sizes can be controlled by a specific choice of heat treatment conditions, subsequently leading to significant changes in the microstructure and mechanical properties of the coatings, such as hardness or wear resistance. In this study, two advanced methods of surface heat treatment were realized by plasma jet or by high energy laser heating. As opposed to the traditional furnace treatments, inducing homogeneous changes throughout the material, both approaches lead to a formation of gradient microstructure within the coatings; from dominantly amorphous at the substrate–coating interface vicinity to fully nanocrystalline near its surface. The processes can also be applied for large-scale applications and do not induce detrimental changes to the underlying substrate materials. The respective mechanical response was evaluated by measuring coating hardness profile and wear resistance. For some of the heat treatment conditions, an increase in the coating microhardness by factor up to 1.8 was observed, as well as improvement of wear resistance behaviour up to 6.5 times. The phase composition changes were analysed by X-ray diffraction and the microstructure was investigated by scanning electron microscopy.

scholarly journals Heat Treatment Evaluation for the Camshafts Production of ADI Low Alloyed with Vanadium

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1036
Author(s):  
Eduardo Colin García ◽  
Alejandro Cruz Ramírez ◽  
Guillermo Reyes Castellanos ◽  
José Federico Chávez Alcalá ◽  
Jaime Téllez Ramírez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ductile Iron ◽  
Volume Fraction ◽  
Energy Impact ◽  
Treatment Conditions ◽  
Mold Casting ◽  
Grade 3 ◽  
Good Agreement

Ductile iron camshafts low alloyed with 0.2 and 0.3 wt % vanadium were produced by one of the largest manufacturers of the ductile iron camshafts in México “ARBOMEX S.A de C.V” by a phenolic urethane no-bake sand mold casting method. During functioning, camshafts are subject to bending and torsional stresses, and the lobe surfaces are highly loaded. Thus, high toughness and wear resistance are essential for this component. In this work, two austempering ductile iron heat treatments were evaluated to increase the mechanical properties of tensile strength, hardness, and toughness of the ductile iron camshaft low alloyed with vanadium. The austempering process was held at 265 and 305 °C and austempering times of 30, 60, 90, and 120 min. The volume fraction of high-carbon austenite was determined for the heat treatment conditions by XRD measurements. The ausferritic matrix was determined in 90 min for both austempering temperatures, having a good agreement with the microstructural and hardness evolution as the austempering time increased. The mechanical properties of tensile strength, hardness, and toughness were evaluated from samples obtained from the camshaft and the standard Keel block. The highest mechanical properties were obtained for the austempering heat treatment of 265 °C for 90 min for the ADI containing 0.3 wt % V. The tensile and yield strength were 1200 and 1051 MPa, respectively, while the hardness and the energy impact values were of 47 HRC and 26 J; these values are in the range expected for an ADI grade 3.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

Effects of Heat Treatment on Microstructure Parameters, Mechanical Properties and Cold Resistance of Sparingly Alloyed High-Strength Steel

2021 ◽  
Vol 410 ◽  
pp. 197-202
Author(s):  
Pavel P. Poleckov ◽  
Olga A. Nikitenko ◽  
Alla S. Kuznetsova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Resistance ◽  
Heating Temperature ◽  
High Strength ◽  
Steel Microstructure ◽  
Treatment Conditions ◽  
Microstructure Parameters ◽  
Temperature Impact ◽  
Low Temperature Impact Toughness

This study considers the influence of various heat treatment conditions on the change of steel microstructure parameters, mechanical properties and cold resistance at a temperature of-60 °C. The common behavior of these properties is considered depending on the heating temperature used for quenching and subsequent tempering. Based on the obtained results, heat treatment conditions are proposed that provide a combination of a guaranteed yield point σ0.2 ≥600 N/mm2 with a low-temperature impact toughness KCV-60 ≥50 J/cm2 and plasticity δ5 ≥17%. The obtained research results are intended for industrial use at the mill "5000" site of MMK PJSC.

scholarly journals Machinability and related properties of austempered ductile iron: A review

2018 ◽  
Vol 12 (4) ◽  
pp. 4180-4190
Author(s):  
Ananda Hegde ◽  
Sathyashankara Sharma ◽  
Gowri Shankar M. C
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Wear Resistance ◽  
Ductile Iron ◽  
High Hardness ◽  
Austempered Ductile Iron ◽  
Spheroidal Graphite ◽  
Light Weight ◽  
Sg Iron

When the ductile iron which is also known as Spheroidal Graphite (SG) iron, is subjected to austempering heat treatment, the material is known as austempered ductile iron (ADI). This material has good mechanical properties and has various applications in different fields. This revolutionary material with its excellent combination of strength, ductility, toughness and wear resistance has the potential to replace some of the commonly used conventional materials such as steel, aluminium and other light weight alloys as it offers production advantage as well. One of the problems encountered during manufacturing is machining of ADI parts owing to its high hardness and wear resistance. Many researchers over a period of time have reported the machinability aspects of the ADI. This paper presents a review on the developments made on the machinability aspects of ADI along with other mechanical properties.

scholarly journals Influence of the energy electron beam exposure regimes on the structure and mechanical properties of composite coatings

2020 ◽  
pp. 23-27
Author(s):  
T.A. Krylova ◽  
◽  
Y.A. Chumakov ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Wear Resistance ◽  
Electron Beam ◽  
Structural Changes ◽  
Composite Coatings ◽  
Initial State ◽  
Austenitic Structure ◽  
Solid Carbide ◽  
Soft Ferrite

The effect of heat treatment on the structure and properties of composite coatings based on chromium carbide with titanium carbide fabricated by non-vacuum electron beam cladding without has been studied. It was shown that tempering leads to a decrease in microhardness and wear resistance, which is associated with the decomposition of the austenitic structure with the formation of a soft ferrite-carbide structure. The post heat treatment tempering was showed to decrease of microhardness and wear resistance, which leads to the decomposition of the austenitic structure with the formation of a soft ferrite-carbide structure. The bulk quenching of coatings after tempering leads to an increase in microhardness comparable to the values of microhardness in the initial state after electron beam cladding, due to the formation of high hard martensite. The wear resistance of composite coatings after tempering is lower than after cladding due to brittle martensite, which is not able to hold solid carbide particles. The composite coatings obtained at the optimal processing conditions have a combination of improved properties and do not require additional heat treatment, resulting in structural changes, causing a decrease in mechanical properties.

Mechanical Behavior of Friction Stir Welded AA-6061 Thick Plates in Different Heat Treatment Conditions

2021 ◽  
Vol 875 ◽  
pp. 203-210
Author(s):  
Talha Ahmed ◽  
Wali Muhammad ◽  
Zaheer Mushtaq ◽  
Mustasim Billah Bhatty ◽  
Hamid Zaigham
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Treatment ◽  
Travel Speed ◽  
Butt Joint ◽  
Tensile Fracture ◽  
Friction Stir ◽  
Treatment Conditions ◽  
Heat Treated ◽  
Joint Form

In this study, mechanical properties of friction stir welded Aluminum Alloy (AA) 6061 in three different heat treatment conditions i.e. Annealed (O), Artificially aged (T6) and Post Weld Heat Treated (PWHT) were compared. Plates were welded in a butt joint form. Parameters were optimized and joints were fabricated using tool rotational speed and travel speed of 500 rpm and 350 mm/min respectively. Two sets of plates were welded in O condition and out of which one was, later, subjected to post weld artificial aging treatment. Third set was welded in T6 condition. The welds were characterized by macro and microstructure analysis, microhardness measurement and mechanical testing. SEM fractography of the tensile fracture surfaces was also performed. Comparatively better mechanical properties were achieved in the plate with PWHT condition.

scholarly journals Effect of heat treatment on the tribological properties of Nickel-Boron electroless coating

2018 ◽  
Vol 27 (47) ◽  
pp. 101
Author(s):  
Sandra Arias ◽  
Maryory Gómez ◽  
Esteban Correa ◽  
Félix Echeverría-Echeverría ◽  
Juan Guillermo Castaño
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Wear Resistance ◽  
Carbon Steel ◽  
Tribological Properties ◽  
Tribological Performance ◽  
Dry Sliding ◽  
Electroless Coating ◽  
Before And After ◽  
Properties Of Materials

Nickel-Boron autocatalytic coatings are widely used in several industries to improve mechanical properties of materials such as hardness and wear resistance. Tribological properties were evaluated in Ni-B autocatalytic coatings deposited on AISI/SAE 1018 carbon steel before and after a heat treatment at 450 °C for one hour. Tribological tests were carried out by dry sliding, using a load of 5 N and a sliding speed of 0.012 m/s, in a homemade ball-on-disk tribometer, which followed ASTM G99 standard. According to the tribological evaluation, the heat treatments applied to Ni-B coatings improved their tribological performance. This research corroborates that by applying an adequate heat treatment, hardness and wear resistance of Ni-B coatings can be improved significantly.

Sign in / Sign up

Export Citation Format

Share Document