scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

scholarly journals Heat Treatment Evaluation for the Camshafts Production of ADI Low Alloyed with Vanadium

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1036
Author(s):  
Eduardo Colin García ◽  
Alejandro Cruz Ramírez ◽  
Guillermo Reyes Castellanos ◽  
José Federico Chávez Alcalá ◽  
Jaime Téllez Ramírez ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ductile Iron ◽  
Volume Fraction ◽  
Energy Impact ◽  
Treatment Conditions ◽  
Mold Casting ◽  
Grade 3 ◽  
Good Agreement

Ductile iron camshafts low alloyed with 0.2 and 0.3 wt % vanadium were produced by one of the largest manufacturers of the ductile iron camshafts in México “ARBOMEX S.A de C.V” by a phenolic urethane no-bake sand mold casting method. During functioning, camshafts are subject to bending and torsional stresses, and the lobe surfaces are highly loaded. Thus, high toughness and wear resistance are essential for this component. In this work, two austempering ductile iron heat treatments were evaluated to increase the mechanical properties of tensile strength, hardness, and toughness of the ductile iron camshaft low alloyed with vanadium. The austempering process was held at 265 and 305 °C and austempering times of 30, 60, 90, and 120 min. The volume fraction of high-carbon austenite was determined for the heat treatment conditions by XRD measurements. The ausferritic matrix was determined in 90 min for both austempering temperatures, having a good agreement with the microstructural and hardness evolution as the austempering time increased. The mechanical properties of tensile strength, hardness, and toughness were evaluated from samples obtained from the camshaft and the standard Keel block. The highest mechanical properties were obtained for the austempering heat treatment of 265 °C for 90 min for the ADI containing 0.3 wt % V. The tensile and yield strength were 1200 and 1051 MPa, respectively, while the hardness and the energy impact values were of 47 HRC and 26 J; these values are in the range expected for an ADI grade 3.

Effects of Heat Treatment on Microstructure Parameters, Mechanical Properties and Cold Resistance of Sparingly Alloyed High-Strength Steel

2021 ◽  
Vol 410 ◽  
pp. 197-202
Author(s):  
Pavel P. Poleckov ◽  
Olga A. Nikitenko ◽  
Alla S. Kuznetsova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Resistance ◽  
Heating Temperature ◽  
High Strength ◽  
Steel Microstructure ◽  
Treatment Conditions ◽  
Microstructure Parameters ◽  
Temperature Impact ◽  
Low Temperature Impact Toughness

This study considers the influence of various heat treatment conditions on the change of steel microstructure parameters, mechanical properties and cold resistance at a temperature of-60 °C. The common behavior of these properties is considered depending on the heating temperature used for quenching and subsequent tempering. Based on the obtained results, heat treatment conditions are proposed that provide a combination of a guaranteed yield point σ0.2 ≥600 N/mm2 with a low-temperature impact toughness KCV-60 ≥50 J/cm2 and plasticity δ5 ≥17%. The obtained research results are intended for industrial use at the mill "5000" site of MMK PJSC.

Strength of Commercial Aluminum Alloys after Equal Channel Angular Pressing and Post-ECAP Processing

2006 ◽  
Vol 114 ◽  
pp. 91-96 ◽  
Author(s):  
Maxim Yu. Murashkin ◽  
M.V. Markushev ◽  
Julia Ivanisenko ◽  
Ruslan Valiev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Aluminum Alloys ◽  
Ultimate Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Room Temperature ◽  
Solution Treatment ◽  
Ecap Processing ◽  
Angular Pressing

The effects of equal channel angular pressing (ECAP), further heat treatment and rolling on the structure and room temperature mechanical properties of the commercial aluminum alloys 6061 (Al-0.9Mg-0.7Si) and 1560 (Al-6.5Mg-0.6Mn) were investigated. It has been shown that the strength of the alloys after ECAP is higher than that achieved after conventional processing. Prior ECAP solution treatment and post-ECAP ageing can additionally increase the strength of the 6061 alloy. Under optimal ageing conditions a yield strength (YS) of 434 MPa and am ultimate tensile strength (UTS) of 470 MPa were obtained for the alloy. Additional cold rolling leads to a YS and UTS of 475 and 500 MPa with 8% elongation. It was found that the post-ECAP isothermal rolling of the 1560 alloy resulted in the formation of a nano-fibred structure and a tensile strength (YS = 540 MPa and UTS = 635 MPa) that has never previously been observed in commercial non-heat treatable alloys.

scholarly journals The Phase Composition and Mechanical Properties of the Novel Precipitation-Strengthening Al-Cu-Er-Mn-Zr Alloy

2020 ◽  
Vol 10 (15) ◽  
pp. 5345
Author(s):  
Sayed Amer ◽  
Olga Yakovtseva ◽  
Irina Loginova ◽  
Svetlana Medvedeva ◽  
Alexey Prosviryakov ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Phase Composition ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Precipitation Strengthening ◽  
The Novel ◽  
Annealed Alloy ◽  
Zr Alloy

The microstructure, phase composition, and mechanical properties during heat treatment and rolling of the novel Al-5.0Cu-3.2Er-0.9Mn-0.3Zr alloy were evaluated. A new quaternary (Al,Cu,Mn,Er) phase with possible composition Al25Cu4Mn2Er was found in the as-cast alloy. Al20Cu2Mn3 and Al3(Zr,Er) phases were nucleated during homogenization, and θ″(Al2Cu) precipitates were nucleated during aging. The metastable disc shaped θ″(Al2Cu) precipitates with a thickness of 5 nm and diameter of 100–200 nm were nucleated mostly on the Al3(Zr,Er) phase precipitates with a diameter of 35 nm. The hardness Vickers (HV) peak was found after the annealing of a rolled alloy at 150 °C due to strengthening by θ″(A2Cu) precipitates, which have a larger effect in materials hardness than do the softening processes. The novel Al-Cu-Er-Mn-Zr alloy has a yield strength (YS) of 320–332 MPa, an ultimate tensile strength (UTS) of 360–370 MPa, and an El. of 3.2–4.0% in the annealed alloy after rolling condition.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

Effect of Heat Treatment on Tensile Strength and Microstructure of AZ61A Magnesium Alloy

2014 ◽  
Vol 606 ◽  
pp. 55-59 ◽  
Author(s):  
R. Senthil ◽  
A. Gnanavelbabu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Mg Alloys ◽  
Forming Process ◽  
Microstructural Parameters ◽  
Heat Treated ◽  
Mutual Relations

Magnesium alloys are the very progressive materials whereon is due to improve their end-use properties. Especially, wrought Mg alloys attract attention since they have more advantageous mechanical properties than cast Mg alloys. Investigations were carried out the effects of heat treatment on tensile strength and microstructure of AZ61A magnesium alloy. The AZ61A Mg alloy is solution heat treated at the temperature of 6500F (343°C) for various soaking timing such as 120 min, 240 min and 360 minutes and allowed it cool slowly in the furnace itself. Magnesium alloys usually are heat treated either to improve mechanical properties or as means of conditioning for specific fabrication operations. Special attention had been focused on the analysis of mutual relations existing between the deformation conditions, microstructural parameters, grain size and the achieved mechanical properties. The result after the solution heat treatment, showed remarkably improved hardness, tensile strength and yield strength. It would be appropriate for a forming process namely isostatic forming process.

scholarly journals Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 71
Author(s):  
Ho-Jung Kang ◽  
Jin-Young Park ◽  
Yoon-Suk Choi ◽  
Dae-Hyun Cho
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Artificial Aging ◽  
Solution Treatment ◽  
Mg Alloys ◽  
Needle Type ◽  
Heat Treated ◽  
Die Cast ◽  
Eutectic Si

Heat treatment is widely used to improve the properties of Al–Si–Mg alloys and its outcomes are influenced by the parameters applied during the treatment. This study describes the effect of the solution and artificial aging treatments on the microstructure and mechanical properties of die-cast Al–Si–Mg alloys. The microstructure of the as-cast Al–Si–Mg alloy was mainly composed of α-Al, complex needle-type eutectic Si particles, Mg2Si, and α-AlFeMn. The complex needle-type eutectic Si particles disintegrated into spheroidal morphologies, while the Mg2Si was dissolved due to the solid solution treatment. The maximum yield strength (YS) and ultimate tensile strength (UTS) values were 126.06 and 245.90 MPa at 520 °C after 90 min of solution heat treatment, respectively. Although the YS and UTS values of the Al–Si–Mg alloys reduced due to the solution treatment, the elongation (EL) of the solid solution heat-treated Al–Si–Mg alloys was improved in comparison to that of the as-cast Al–Si–Mg alloy. The maximum YS and UTS of 239.50 and 290.93 MPa were obtained after performing artificial aging at 180 °C for 180 min, respectively. However, the EL of the aging heat-treated alloy was reduced by a minimal value.

Mechanical Properties of a Mild-Alloy Steel for Aerospace Engineering

2021 ◽  
Vol 410 ◽  
pp. 221-226
Author(s):  
Mikhail V. Maisuradze ◽  
Maxim A. Ryzhkov ◽  
Dmitriy I. Lebedev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Strength ◽  
Aerospace Engineering ◽  
Isothermal Heat Treatment ◽  
Tempering Temperature ◽  
Optimal Heat Treatment ◽  
Treatment Conditions ◽  
Quenching And Tempering ◽  
Conventional Oil

The features of microstructure and mechanical properties of the aerospace high strength steel were studied after the implementation of various heat treatment modes: conventional oil quenching and tempering, quenching-partitioning, austempering. The dependence of the mechanical properties on the tempering temperature was determined. The basic patterns of the formation of mechanical properties during the implementation of isothermal heat treatment were considered. The optimal heat treatment conditions for the studied steel were established.

scholarly journals EFFECT OF SN COMPONENT ON PROPERTIES AND MICROSTRUCTURE CU-NI-SN ALLOYS

2018 ◽  
Vol 80 (6) ◽  
Author(s):  
D. N. Nguyen ◽  
A. T. Hoang ◽  
X. D. Pham ◽  
M. T. Sai ◽  
M. Q. Chau ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Electrical Conductivity ◽  
Tensile Strength ◽  
Spinodal Decomposition ◽  
Deformation Mechanism ◽  
Elastic Limit ◽  
High Strength ◽  
High Electrical Conductivity ◽  
X Ray

This paper investigates a high electrical conductivity and high strength of alloys based on Cu-Ni-Si system It proclaimed the results of the effect of tin (Sn) component on the mechanical properties and microstructure of Cu-Ni-Sn alloy. The conditions for processing the Cu-Ni-Si alloy were presented, the analysis of microstructure and mechanical properties after heat treatment was examined by X-ray, SEM, EDS and specialized machines. The results showed that with 3% mass of Sn added into the Cu-Ni-Sn alloy along with heat treatment and deformation, the hardness value reached the range of 221-240HV, the tensile strength and elastic limit reached around 1060MPa and 903MPa respectively. However, after heat treatment and deformation for the Cu-Ni-Sn alloy based on 6% mass of Sn, the hardness value reached the range of 221-318HV, the tensile strength and elastic limit were respectively 222MPa and 263MPa higher than those of the Cu-Ni-Sn alloy with 3% mass of Sn. The result from X-ray analysis showed the deflection of peaks. Nonetheless, the new phases were not observed in SEM and EDS, contrariwise, generated modular structure was considered as the proof of the Spinodal cluster. This fact might be explained by two mechanisms: deformation mechanism and Spinodal decomposition.

Sign in / Sign up

Export Citation Format

Share Document