scholarly journals Laser Surface Hardening of Gun Metal Alloys

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2632
Author(s):  
Samia Naeem ◽  
Tahir Mehmood ◽  
K. M. Wu ◽  
Babar Shahzad Khan ◽  
Abdul Majid ◽  
...  
Keyword(s):  
Defect Density ◽  
Laser System ◽  
Surface Hardness ◽  
Hardness Test ◽  
Wave Number ◽  
Raman Shift ◽  
Hardness Profile ◽  
X Ray Diffraction ◽  
Treated Sample ◽  
Dislocation Defect

The effect of laser irradiation with different numbers of laser shots on the microstructure, the surface, and the hardness of gun metal alloy was studied by a KrF pulsed excimer laser system, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and Vickers hardness test. The influence of 100–500 laser shots was irradiated on the surface hardness profile and on the microstructure of gunmetal alloy. XRD results showed the maximum 2θ shift, the maximum full width of half maximum FWHM, the maximum dislocation density, and the minimum crystallite size for the sample irradiated with 300 laser shots. The hardness was measured in three different regions at the laser irradiated spot, and it was found that maximum hardness was present at the heat affected zone for all samples. The hardness value of the un-irradiated sample of gun metal was 180, and the value increased up to 237 by raising the number of laser shots up to 300. The peak value of surface hardness of the laser treated sample was 32% higher than the un-irradiated sample. The Raman shift of the un-exposed sample was 605 cm−1 and shifted to a higher value of wave number at 635 cm−1 at 300 laser shots. The hardness value was decreased by further increasing the number of laser shots up to 500. The samples irradiated with 400 and 500 laser shots exhibited smaller hardness and dislocation defect density, which was assigned to possible annealing caused by irradiation.

Laser Surface Modification of Tool Steel for Semi-Solid Steel Forming

2008 ◽  
Vol 141-143 ◽  
pp. 255-260 ◽  
Author(s):  
Dermot Brabazon ◽  
Sumsun Naher ◽  
Patrick Biggs
Keyword(s):  
Surface Modification ◽  
Tool Steel ◽  
Co2 Laser ◽  
Surface Hardness ◽  
Amorphous State ◽  
Processing Parameters ◽  
Hardness Profile ◽  
X Ray Diffraction ◽  
Thermal Barriers ◽  
Semi Solid

This paper presents an analysis of the effect of CO2 laser processing parameters on the surface modification and heat treatment of steels. The CO2 laser and sample movement process parameters are presented. The controlled operation of these in conjunction with each other is required to obtain better surface hardness and structure. H13 tool steel samples were rotated at high speeds to keep exposure times below 0.3s. Laser processed samples were analysed using EDX spectroscopy, optical microscopy, Vickers and Martens micro-hardness testing, and X-ray diffraction (XRD). Results show how the hardness profile through the surface is related to the laser treatment and resultant microstructures. Increased surface hardness was noted due to a complete microstructural transformation to an amorphous state in the glazed samples. The usefulness of such coatings on tool steels, in conjunction with other thermal barriers, for the forming of semi-solid steel alloys is presented.

Micro-Hardness and Morphology of LDPE Influenced by Beta Radiation

2014 ◽  
Vol 606 ◽  
pp. 253-256 ◽  
Author(s):  
Martin Ovsik ◽  
Petr Kratky ◽  
David Manas ◽  
Miroslav Manas ◽  
Michal Stanek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Hardness Test ◽  
Polymer Materials ◽  
Beta Radiation ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Depth Sensing ◽  
Surface Layers ◽  
Hardness Values ◽  
Different Doses

This article deals with the influence of different doses of Beta radiation to the structure and mico-mechanical properties of Low-density polyethylene (LDPE). Hard surface layers of polymer materials, especially LDPE, can be formed by radiation cross-linking by β radiation with doses of 33, 66 and 99 kGy. Material properties created by β radiation are measured by micro-hardness test using the DSI method (Depth Sensing Indentation). Individual radiation doses caused structural and micro-mechanical changes which have a significant effect on the final properties of the LDPE tested. The highest values of micro-mechanical properties were reached at radiation dose of 66 and 99 kGy, when the micro-hardness values increased by about 21%. The changes were examined and confirmed by X-ray diffraction.

Surface Hardness Modify and Improve Wear Properties of EP\ NanoZrO2

2021 ◽  
Vol 19 (2) ◽  
pp. 77-82
Author(s):  
Fadhil K. Farhan ◽  
Aws Abbas Hussein ◽  
Ali Q. Tuama
Keyword(s):  
Wear Resistance ◽  
High Surface ◽  
Ceramic Powder ◽  
High Surface Area ◽  
Surface Hardness ◽  
Weight Ratio ◽  
Hardness Test ◽  
Wear Properties ◽  
Mechanical Mixing ◽  
Dioxide Powder

The liquid and mechanical mixing method was used in addition to ultrasound technology to prepare samples according to standard conditions. The percentage of cementing with ceramic powder was adopted from 1% to 4% as a weight ratio, and by using mixing drivers, nanocomposites were prepared depending on the theoretical density of the components. The velvet density was measured using Archimedes' method, and the results showed a successive improvement and increase in density with the weight ratio of addition. The results of the particulate hardness test showed a significant improvement in the results of the prepared nanostructures compared to the base sample (pure epoxy). With regard to the properties of wear resistance (wear modulus) using the screw-on-disk method, the cemented samples showed a higher wear resistance compared to the base sample. The results were interpreted based on the values of density and hardness in addition to the properties possessed by the ceramic powder of high surface area and average granular size of 32 nanometers through scanning electron microscopy. In this work, nanostructures based on (a polymer) supported with nanoscale zirconium dioxide powder were developed.

Effect of Coating Bath Parameters on Properties of Electroless Nickel-Boron Alloy Coatings

2022 ◽  
Vol 10 (1) ◽  
pp. 0-0
Keyword(s):  
Surface Roughness ◽  
Surface Hardness ◽  
Chloride Concentration ◽  
Electroless Nickel ◽  
Nickel Chloride ◽  
Scratch Test ◽  
X Ray Diffraction ◽  
Tribological Behaviour ◽  
Pin On Disc ◽  
Mechanical Behaviours

Electroless nickel-boron binary coatings were obtained with various bath compositions to investigate the effect of bath parameters on tribological and mechanical behaviours of the coating. Characterisation of the coating for surface morphology and phase structure is done using Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD), respectively, whereas tribological behaviour of coatings is evaluated on a pin-on-disc tribo-tester. Elastic modulus and surface hardness of coatings have been obtained using nano-indentation technique, while the scratch behaviour of the coatings has been determined using micro-scratch test. Corrosion resistance of coatings is also determined. It is observed that surface roughness of the coatings increased with increase in sodium borohydride concentration but decreased slightly with increase in nickel chloride concentration. Friction and wear characteristics are found to increase with surface roughness which occurs due to increased boron content. Surface hardness and scratch hardness are also seen to vary with coating bath parameters.

Growth of Si1−xGex, Strained Layers Using Atmospheric-Pressure CVD

1991 ◽  
Vol 220 ◽  
Author(s):  
F. Namavar ◽  
J. M. Manke ◽  
E. P. Kvam ◽  
M. M. Sanfacon ◽  
C. H. Perry ◽  
...  
Keyword(s):  
Atmospheric Pressure ◽  
Defect Density ◽  
Chemical Vapor ◽  
Good Growth ◽  
X Ray Diffraction ◽  
Strained Layers ◽  
Dislocation Glide ◽  
Transmission Electron ◽  
Pressure Chemical ◽  
Film Defect

ABSTRACTThe objective of this paper is to demonstrate the epitaxial growth of SiGe strained layers using atmospheric-pressure chemical vapor deposition (APCVD). We have grown SiGe layers with various thicknesses and Ge concentrations at temperatures ranging from 800–1000°C. The samples were studied using a variety of methods, including transmission electron microscopy (TEM), high resolution X-ray diffraction (HRXRD) and Raman spectroscopy (RS). Both HRXRD and RS results indicate that samples with about 10% Ge and a thickness of about 1000 Å are almost fully strained. TEM analyses of these samples indicate a film defect density less than 105/cm2. SIMS results indicate that the oxygen concentration in the epitaxial layers is lower than that found in CZ substrates.Our analyses also indicate that as-grown epitaxial Ge layers several microns thick have a defect density less than 107/cm2. The relatively low defect density in both SiGe and Ge layers grown on Si has been attributed to far higher dislocation glide velocity at the relatively elevated growth temperatures employed in CVD and to very good growth cleanliness.

Thermotropic behavior of sodium cholesteryl carbonate

2009 ◽  
Vol 24 (1) ◽  
pp. 156-163 ◽  
Author(s):  
Rabkwan Chuealee ◽  
Timothy S. Wiedmann ◽  
Teerapol Srichana
Keyword(s):  
Phase Behavior ◽  
Chemical Structure ◽  
Liquid Crystalline ◽  
Polarized Light ◽  
Wave Number ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
X Ray Scattering ◽  
C Nmr

Sodium cholesteryl carbonate ester (SCC) was synthesized, and its phase behavior was studied. The chemical structure was assessed by solid-state infrared spectroscopy based on vibration analysis. The wave number at 1705 and 1276 cm−1 corresponds to a carbonyl carbonate and O–C–O stretching of SCC, respectively. Molecular structure of SCC was further investigated with 1H and 13C NMR spectroscopy. The chemical shift, for the carbonyl carbonate resonance appeared at 155.5 ppm. A molecular mass of SCC was at m/z of 452. Differential scanning calorimetry (DSC), video-enhanced microscopy (VEM) together with polarized light microscopy, and small-angle x-ray scattering (SAXS) were used to characterize the phase behavior as a function of temperature of SCC. Liquid crystalline phase was formed with SCC. Based on the thermal properties and x-ray diffraction, it appears that SCC forms a structure analogous to the type II monolayer structure observed with cholesterol esters.

scholarly journals The time-resolved hard X-ray diffraction endstation KMC-3 XPP at BESSY II

2021 ◽  
Vol 28 (3) ◽  
Author(s):  
Matthias Rössle ◽  
Wolfram Leitenberger ◽  
Matthias Reinhardt ◽  
Azize Koç ◽  
Jan Pudell ◽  
...  
Keyword(s):  
Storage Ring ◽  
Single Photon ◽  
Laser System ◽  
High Vacuum ◽  
Laser Pulses ◽  
Pixel Detector ◽  
X Ray Diffraction ◽  
Optical Pump ◽  
Time Resolved ◽  
X Ray

The time-resolved hard X-ray diffraction endstation KMC-3 XPP for optical pump/X-ray probe experiments at the electron storage ring BESSY II is dedicated to investigating the structural response of thin film samples and heterostructures after their excitation with ultrashort laser pulses and/or electric field pulses. It enables experiments with access to symmetric and asymmetric Bragg reflections via a four-circle diffractometer and it is possible to keep the sample in high vacuum and vary the sample temperature between ∼15 K and 350 K. The femtosecond laser system permanently installed at the beamline allows for optical excitation of the sample at 1028 nm. A non-linear optical setup enables the sample excitation also at 514 nm and 343 nm. A time-resolution of 17 ps is achieved with the `low-α' operation mode of the storage ring and an electronic variation of the delay between optical pump and hard X-ray probe pulse conveniently accesses picosecond to microsecond timescales. Direct time-resolved detection of the diffracted hard X-ray synchrotron pulses use a gated area pixel detector or a fast point detector in single photon counting mode. The range of experiments that are reliably conducted at the endstation and that detect structural dynamics of samples excited by laser pulses or electric fields are presented.

scholarly journals KARAKTERISTIK SIFAT MEKANIS ANTARA TIGA PRODUK MANUFAKTUR ELEKTRODA E6013

2019 ◽  
Vol 3 (1) ◽  
pp. 40-45
Author(s):  
Basori Basori ◽  
Ferry Budhi Susetyo
Keyword(s):  
Impact Strength ◽  
Test Specimen ◽  
Impact Test ◽  
Surface Hardness ◽  
Welding Process ◽  
Hardness Test ◽  
Bottom Plate ◽  
Weld Deposit ◽  
Welding Electrode ◽  
The Impact

The type of electrode used in the SMAW process has many types, such as E 6010, E 6011, E 6012, E 6013, E 6020, E6027. In this case the type E 6013 is the most widely used. Certainly the type E 6013 is produced by different manufacturers as well. From penelurusan researchers of this type have different prices in accordance with companies that sell it. For that reason researchers are interested to compare the three manufacturing outputs for the type E 6013 in terms of its mechanical properties. Making a specimen welding electrode cut material to be used. then sandpaper the material that has been cut so that no remaining pieces are still attached. The next step to do the welding process with three types of E6013 elekroda. The welding is carried out until it reaches the layer layer 10 mm thickness, then the bottom plate is discarded and the weld deposit deposits only The impact strength and surface hardness value are inversely proportional. For the impact test, the E1 electrode sample specimen has the highest impact strength value and the E3 electrode sample specimen has the lowest impact strength value. While on the hardness test specimen E3 electrode sample has the highest hardness value and sample specimen E1 electrode has the lowest hardness value. This can prove that the harder the object is the more brittle the object.

EFFECT OF NITROGEN AMOUNT ON TRIBOLOGICAL BEHAVIOR OF PLASMA NITRIDED 31CrMoV9 STEEL

2019 ◽  
Vol 26 (07) ◽  
pp. 1850217 ◽  
Author(s):  
O. ÇOMAKLI ◽  
A. F. YETIM ◽  
B. KARACA ◽  
A. ÇELIK
Keyword(s):  
Wear Resistance ◽  
Tribological Behavior ◽  
Wear Behavior ◽  
Plasma Nitriding ◽  
Surface Hardness ◽  
Compound Layer ◽  
Gas Mixture ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pin On Disk

The 31CrMoV9 steels were plasma nitrided under different gas mixture ratios to investigate an influence of nitrogen amount on wear behavior. The structure, mechanical and tribological behavior of untreated and nitrided 31CrMoV9 steels were analyzed with X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), microhardness device, 3D profilometer and pin-on-disk wear tester. The analysis outcomes displayed that the compound layer consists of nitride phases (Fe2N, Fe3N, Fe4N and CrN). Additionally, the thickness of the compound layers, surface hardness and roughness increased with increasing nitrogen amount in the gas mixture. The highest friction coefficient value was obtained at nitrogen amount of 50%, but the lowest value was seen at nitrogen amount of 6%. It was observed that wear resistance of 31CrMoV9 steel improved after plasma nitriding, and the best wear resistance was also obtained from plasma nitrided sample at the gas mixture of 94% H[Formula: see text]% N2.

Sign in / Sign up

Export Citation Format

Share Document