scholarly journals Influence of Wood-Based Biomass Ash Admixing on the Structural, Mechanical, Hygric, and Thermal Properties of Air Lime Mortars

Materials ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2227 ◽  
Author(s):  
Milena Pavlíková ◽  
Lucie Zemanová ◽  
Jaroslav Pokorný ◽  
Martina Záleská ◽  
Ondřej Jankovský ◽  
...  
Keyword(s):  
Building Materials ◽  
Mechanical Test ◽  
Low Cost ◽  
Simultaneous Thermal Analysis ◽  
Fluorescence Analysis ◽  
X Ray Diffraction ◽  
Biomass Ash ◽  
X Ray ◽  
Binder Ratio ◽  
Active Admixture

Mechanically-activated wood-based biomass ash (WBA) was studied as a potential active admixture for design of a novel lime-pozzolan-based mortar for renovation purposes. The replacement ratio of lime hydrate in a mortar mix composition was 5%, 10%, and 15% by mass. The water/binder ratio and the sand/binder ratio were kept constant for all examined mortar mixes. Both binder constituents were characterized by their powder density, specific density, BET (Brunauer–Emmett–Teller), and Blaine specific surfaces. Their chemical composition was measured by X-ray fluorescence analysis (XRF) and mineralogical analysis was performed using X-ray diffraction (XRD). Morphology of WBA was investigated by scanning electron microscopy (SEM) and element mapping was performed using an energy dispersive spectroscopy (EDS) analyzer. The pozzolanic activity of WBA was tested by the Chapelle test and assessment of the Portlandite content used simultaneous thermal analysis (STA). For the hardened mortar samples, a complete set of structural, mechanical, hygric, and thermal parameters was experimentally determined. The mortars with WBA admixing yielded similar or better functional properties than those obtained for traditional pure lime-based plaster, pointing to their presumed application as rendering and walling renovation mortars. As the Chapelle test, STA, and mechanical test proved high pozzolanity of WBA, it was classified as an alternative eco-efficient low-cost pozzolan for use in lime blend-based building materials. The savings in CO2 emissions and energy by the use of WBA as a partial lime hydrate substitute in mortar composition were also highly appreciated with respect to the sustainability of the construction industry.

scholarly journals Magnesium Oxybromides MOB-318 and MOB-518: Brominated Analogues of Magnesium Oxychlorides

2020 ◽  
Vol 10 (11) ◽  
pp. 4032
Author(s):  
Anna-Marie Lauermannová ◽  
Michal Lojka ◽  
Filip Antončík ◽  
David Sedmidubský ◽  
Milena Pavlíková ◽  
...  
Keyword(s):  
Building Materials ◽  
Simultaneous Thermal Analysis ◽  
Heating Process ◽  
X Ray Diffraction ◽  
Sustainable Building ◽  
X Ray ◽  
Environmentally Sustainable ◽  
Transmission Electron ◽  
Magnesium Oxychloride ◽  
Sustainable Building Materials

The search for environmentally sustainable building materials is currently experiencing significant expansion. It is increasingly important to find new materials or reintroduce those that have been set aside to find a good replacement for Portland cement, which is widely used despite being environmentally insufficient and energy-intensive. Magnesium oxybromides, analogues to well-known magnesium oxychloride cements, fit both categories of new and reintroduced materials. In this contribution, two magnesium oxybromide phases were prepared and thoroughly analyzed. The stoichiometries of the prepared phases were 5Mg(OH)2∙MgBr2∙8H2O and 3Mg(OH)2∙MgBr2∙8H2O. The phase analysis was determined using X-ray diffraction. The morphology was analyzed with scanning and transmission electron microscopy. The chemical composition was studied using X-ray fluorescence and energy dispersive spectroscopy. Fourier transform infrared spectroscopy was also used. The thermal stability and the mechanism of the release of gasses linked to the heating process, such as water and hydrobromic acid evaporation, were analyzed using simultaneous thermal analysis combined with mass spectroscopy. The obtained results were compared with the data available for magnesium oxychlorides.

scholarly journals Multidimensional Ln-Aminophthalate Photoluminescent Coordination Polymers

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1786
Author(s):  
Carla Queirós ◽  
Chen Sun ◽  
Ana M. G. Silva ◽  
Baltazar de Castro ◽  
Juan Cabanillas-Gonzalez ◽  
...  
Keyword(s):  
Water Content ◽  
Coordination Polymers ◽  
Metal Ion ◽  
Low Cost ◽  
Microwave Assisted Synthesis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wide Range ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

The development of straightforward reproducible methods for the preparation of new photoluminescent coordination polymers (CPs) is an important goal in luminescence and chemical sensing fields. Isophthalic acid derivatives have been reported for a wide range of applications, and in addition to their relatively low cost, have encouraged its use in the preparation of novel lanthanide-based coordination polymers (LnCPs). Considering that the photoluminescent properties of these CPs are highly dependent on the existence of water molecules in the crystal structure, our research efforts are now focused on the preparation of CP with the lowest water content possible, while considering a green chemistry approach. One- and two-dimensional (1D and 2D) LnCPs were prepared from 5-aminoisophthalic acid and Sm3+/Tb3+ using hydrothermal and/or microwave-assisted synthesis. The unprecedented LnCPs were characterized by single-crystal X-ray diffraction (SCRXD), powder X-ray diffraction (PXRD), Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM), and their photoluminescence (PL) properties were studied in the solid state, at room temperature, using the CPs as powders and encapsulated in poly(methyl methacrylate (PMMA) films, envisaging the potential preparation of devices for sensing. The materials revealed interesting PL properties that depend on the dimensionality, metal ion, co-ligand used and water content.

Transient liquid phase bonding of Cu and Al using metallic particles interlayers

2021 ◽  
pp. 095440542098823
Author(s):  
Alireza Zaheri ◽  
Mohammadreza Farahani ◽  
Alireza Sadeghi ◽  
Naser Souri
Keyword(s):  
Liquid Phase ◽  
Mechanical Test ◽  
Transient Liquid Phase ◽  
Transient Liquid Phase Bonding ◽  
Joint Interface ◽  
Test Results ◽  
X Ray Diffraction ◽  
X Ray ◽  
Metallic Particles ◽  
Powder Interlayer

The bonding strength, and microstructures of Cu and Al couples using metallic powders as interlayer during transient liquid phase bonding (TLP bonding) were investigated. The interfacial morphologies and microstructures were studied by scanning electron microscopy equipped with energy dispersive X-ray spectroscopy, and X-ray diffraction. First, to explore the optimum bonding time and temperature, nine samples were bonded without interlayers in a vacuum condition. Mechanical test results indicated that bonding at 560°C in 20 min returns the highest bond strength (84% of Al). This bonding condition was used to join ten samples with powder interlayers. Powders were prepared by mixing different combinations of Cu, Al (+Fe nanoparticles) and Zn. In the bonding zone, different Cu9Al4, CuAl, and CuAl2 intermetallic co-precipitate. The strongest bonding is formed in the sample with the 70Al (+Fe)-30Cu powder interlayer. Powder interlayers present thinner and more uniform intermetallic layers at the joint interface.

scholarly journals Mechanochemical Preparation of Slow Release Fertilizer Based on Glauconite–Urea Complexes

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 507 ◽  
Author(s):  
Maxim Rudmin ◽  
Elshan Abdullayev ◽  
Alexey Ruban ◽  
Ales Buyakov ◽  
Bulat Soktoev
Keyword(s):  
Milling Time ◽  
Slow Release ◽  
Mechanochemical Activation ◽  
Structural Characteristics ◽  
Fluorescence Analysis ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Mechanochemical Method ◽  
X Ray ◽  
Slow Release Fertilizers

We investigated the mechanochemical synthesis of complex slow release fertilizers (SRF) derived from glauconite. We studied the effectiveness of the mechanical intercalation of urea into glauconite using planetary and ring mills. The potassium-nitric complex SRFs were synthesized via a mechanochemical method mixing glauconite with urea in a 3:1 ratio. The obtained composites were analyzed using X-ray diffraction analysis, scanning electron microscopy, X-ray fluorescence analysis, and infrared spectroscopy. The results show that as duration of mechanochemical activation increases, the mineralogical, chemical, and structural characteristics of composites change. Essential modifications associated with a decrease in absorbed urea and the formation of microcrystallites were observed when the planetary milling time increased from 5 to 10 min and the ring milling from 15 to 30 min. Complete intercalation of urea into glauconite was achieved by 20 min grinding in a planetary mill or 60 min in a ring mill. Urea intercalation in glauconite occurs much faster when using a planetary mill compared to a ring mill.

A Novel Missense Mutation (p.P52R) in Amelogenin Gene Causing X-linked Amelogenesis Imperfecta

2007 ◽  
Vol 86 (1) ◽  
pp. 69-72 ◽  
Author(s):  
M. Kida ◽  
Y. Sakiyama ◽  
A. Matsuda ◽  
S. Takabayashi ◽  
H. Ochi ◽  
...  
Keyword(s):  
Novel Mutation ◽  
Dental Enamel ◽  
Fluorescence Analysis ◽  
Hereditary Disease ◽  
Amelogenesis Imperfecta ◽  
X Ray Diffraction ◽  
Japanese Family ◽  
X Ray ◽  
Amelogenin Gene

Amelogenesis imperfecta (AI) is a hereditary disease with abnormal dental enamel formation. Here we report a Japanese family with X-linked AI transmitted over at least four generations. Mutation analysis revealed a novel mutation (p.P52R) in exon 5 of the amelogenin gene. The mutation was detected as heterozygous in affected females and as hemizygous in their affected father. The affected sisters exhibited vertical ridges on the enamel surfaces, whereas the affected father had thin, smooth, yellowish enamel with distinct widening of inter-dental spaces. To study the pathological cause underlying the disease in this family, we synthesized the mutant amelogenin p.P52R protein and evaluated it in vitro. Furthermore, we studied differences in the chemical composition between normal and affected teeth by x-ray diffraction analysis and x-ray fluorescence analysis. We believe that these results will greatly aid our understanding of the pathogenesis of X-linked AI.

A simple and low-cost solution for the automation of X-ray powder diffractometers with chart recorder output

2006 ◽  
Vol 39 (4) ◽  
pp. 626-629
Author(s):  
M. Jayaprakasan ◽  
V. Kannan ◽  
P. Ramasamy
Keyword(s):  
Quantitative Analysis ◽  
Low Cost ◽  
Hard Copy ◽  
X Ray Diffraction ◽  
Raw Data ◽  
Crystalline Materials ◽  
X Ray ◽  
Strip Chart ◽  
Controlled Systems ◽  
Chart Recorder

X-ray powder diffraction is an established method for the qualitative identification of crystalline materials and their quantitative analysis. The new generation of X-ray diffraction systems are based on expensive digital/embedded control technology and computer interfaces. Yet many laboratories use conventional manual-controlled systems withXYstrip-chart recorders. Since the output spectrum is a strip chart (hard copy), raw data, essential for structural and qualitative analysis, are not readily available for further analysis. Upgrading to modern computerized diffractometers is very expensive. The proposed automation design described here is intended to enable the conventional diffractometer user to collect, store and analyze data quickly. The design also improves the resolution by five times compared with the conventional setup. For the automation, a PC add-on card has been designed to control and collect the timing and intensity counts from the conventional X-ray diffractometer, and suitable software has been developed to collect, process and present the X-ray diffraction data for both qualitative and quantitative analysis. Moreover, a major advantage of this design is that it does not warrant any physical modification of the hardware of the conventional setup; it is simply an extension to enhance the performance of collecting raw data with a higher resolution at desired intervals/timings.

Low-cost thermo-chemical process of TiO2 powder purification: Study of iterative gettering effect

2021 ◽  
Author(s):  
Nesrine Jaouabi ◽  
Wala Medfai ◽  
Marouan Khalifa ◽  
Rabia Zaghouani ◽  
Hatem Ezzaouia
Keyword(s):  
Porous Layer ◽  
Sacrificial Layer ◽  
Low Cost ◽  
Nir Spectroscopy ◽  
Tio2 Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Density Reduction ◽  
Transmission Electron ◽  
Layer Effect

The titanium dioxide (TiO2) purity is very important for the TiO2-based applications making essential the impurities density reduction. In this study, we propose an efficient purification process of TiO2 powder in order to reduce impurities. The low-cost proposed approach is based on an iterative gettering (IG) process combining three main steps: (1) a porous TiO2 sacrificial layer formation (p-TiO2), (2) a rapid thermal annealing (RTA) of p-TiO2 powder in an infrared oven at 950°C under air permitting the residual impurities diffusion to the porous layer surface and (3) etching in acid solution to remove the porous layer. Effect of the proposed gettering process on purification efficiency was evaluated by different characterization techniques such as the transmission electron microscopy (TEM), the energy dispersive x-ray spectroscopy (EDX), the UV–Visible-NIR spectroscopy, the X-ray diffraction (XRD) and atomic absorption spectroscopy (AAS). The obtained results showed the efficient removal of metal impurities, such as Cu, Al, P, and Fe confirming the efficiency of the process improving the purity from 89% to 99.96%.

scholarly journals Extraction of γ-Alumina from Low-Cost Kaolin

Resources ◽  
2018 ◽  
Vol 7 (4) ◽  
pp. 63
Author(s):  
Khalil Ibrahim ◽  
Mohammad Moumani ◽  
Salsabeela Mohammad
Keyword(s):  
Low Cost ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Aluminum Metal ◽  
Alumina Particles ◽  
Two Stages ◽  
Method Of Extraction ◽  
Microcrystalline Powder ◽  
Made In

A combined process is proposed for the utilization of local kaolin to produce alumina particles. The applied process is made in two stages: calcination at 700 °C with sodium chloride and leaching with sulfuric followed by hydrochloric acids. The optimal extraction efficiency can be obtained when the conditions are as follows: leaching temperature is at 140 °C, leaching time is 3 h 45 min and concentration of sulfuric acid is 40 wt.%. The results show that the purity of alumina reaches 79.28%, which is suitable for the production of aluminum metal. It is evident that this method of extraction of alumina from the kaolin ash is practical and feasible. The structural and morphological properties of the calcined microcrystalline powder was characterized by X-ray diffraction and scanning electron microscope (SEM).

Characteristics of New Pyrolitic Graphite Crystal for X - ray Diffraction and Fluorescence Analysis

1994 ◽  
pp. 545-552 ◽  
Author(s):  
Katsumi Ohno ◽  
Mutsuaki Murakami ◽  
Toshiharu Hoshi ◽  
Mutsuaki Murakami ◽  
Toshiharu Hoshi ◽  
...  
Keyword(s):  
Fluorescence Analysis ◽  
X Ray Diffraction ◽  
Graphite Crystal ◽  
X Ray

scholarly journals Thermal Stability and Kinetics of Formation of Magnesium Oxychloride Phase 3Mg(OH)2∙MgCl2∙8H2O

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 767 ◽  
Author(s):  
Michal Lojka ◽  
Ondřej Jankovský ◽  
Adéla Jiříčková ◽  
Anna-Marie Lauermannová ◽  
Filip Antončík ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Construction Materials ◽  
Simultaneous Thermal Analysis ◽  
Rietveld Analysis ◽  
X Ray Diffraction ◽  
Sustainable Building ◽  
X Ray ◽  
Kinetics Of Formation ◽  
Magnesium Oxychloride ◽  
Kinetics Of

In this paper, magnesium oxychloride cement with stoichiometry 3Mg(OH)2∙MgCl2∙8H2O (MOC 3-1-8) was prepared and characterized. The phase composition and kinetics of formation were studied by X-ray diffraction (XRD) and Rietveld analysis of obtained diffractograms. The chemical composition was analyzed using X-ray fluorescence (XRF) and energy dispersive spectroscopy (EDS). Furthermore, scanning electron microscopy (SEM) was used to study morphology, and Fourier Transform Infrared (FT-IR) spectroscopy was also used for the analysis of the prepared sample. In addition, thermal stability was tested using simultaneous thermal analysis (STA) combined with mass spectroscopy (MS). The obtained data gave evidence of the fast formation of MOC 3-1-8, which started to precipitate rapidly. As the length of the time of ripening increased, the amount of MgO decreased, while the amount of MOC 3-1-8 increased. The fast formation of the MOC 3-1-8 phase at an ambient temperature is important for its application in the production of low-energy construction materials, which corresponds with the challenges of a sustainable building industry.

Sign in / Sign up

Export Citation Format

Share Document