scholarly journals Effect of Layer-Wise Varying Parameters on the Microstructure and Soundness of Selective Laser Melted INCONEL 718 Alloy

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2165 ◽  
Author(s):  
Xiang Wang ◽  
Jinwu Kang ◽  
Tianjiao Wang ◽  
Pengyue Wu ◽  
Tao Feng ◽  
...  
Keyword(s):  
Energy Density ◽  
Inconel 718 ◽  
Laser Energy ◽  
Scanning Speed ◽  
High Energy ◽  
High Energy Density ◽  
Inconel 718 Alloy ◽  
Melt Pool ◽  
Columnar Grains ◽  
Melt Pool Size

Selective laser melting (SLM) is a promising powder bed fusion additive manufacturing technique for metal part fabrication. In this paper, varying scanning speed in the range of 500 mm/s to 1900 mm/s, and laser power in the range of 100 W to 200 W, were realized from layer to layer in a cycle of 56 layers in a single cuboid Inconel 718 alloy specimen through SLM. Layer-wise variation of microstructure and porosity were acquired, showing the layer-wise controlling capability of microstructural soundness. The melt pool size and soundness are closely linked with the energy input. High energy density led to sound regions with larger, orderly stacked melt pools and columnar grains, while low energy density resulted in porous regions with smaller, mismatched melt pools, un-melted powder, and equiaxed grains with finer dendrites. With the increase of laser energy density, the specimen shifts from porous region to sound region within several layers.

scholarly journals A Comparative Analysis of Laser Additive Manufacturing of High Layer Thickness Pure Ti and Inconel 718 Alloy Materials Using Finite Element Method

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 876 ◽  
Author(s):  
Sapam Ningthemba Singh ◽  
Sohini Chowdhury ◽  
Yadaiah Nirsanametla ◽  
Anil Kumar Deepati ◽  
Chander Prakash ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Layer Thickness ◽  
Inconel 718 ◽  
Laser Power ◽  
Scanning Speed ◽  
Laser Additive Manufacturing ◽  
Inconel 718 Alloy ◽  
Melt Pool ◽  
High Layer

Investigation of the selective laser melting (SLM) process, using finite element method, to understand the influences of laser power and scanning speed on the heat flow and melt-pool dimensions is a challenging task. Most of the existing studies are focused on the study of thin layer thickness and comparative study of same materials under different manufacturing conditions. The present work is focused on comparative analysis of thermal cycles and complex melt-pool behavior of a high layer thickness multi-layer laser additive manufacturing (LAM) of pure Titanium (Ti) and Inconel 718. A transient 3D finite-element model is developed to perform a quantitative comparative study on two materials to examine the temperature distribution and disparities in melt-pool behaviours under similar processing conditions. It is observed that the layers are properly melted and sintered for the considered process parameters. The temperature and melt-pool increases as laser power move in the same layer and when new layers are added. The same is observed when the laser power increases, and opposite is observed for increasing scanning speed while keeping other parameters constant. It is also found that Inconel 718 alloy has a higher maximum temperature than Ti material for the same process parameter and hence higher melt-pool dimensions.

Effect of Temperature on the Evolved Microstructure During Laser Beam Forming of Sheet Steels

2017 ◽  
Author(s):  
Stephen Akinlabi ◽  
Madindwa Mashinini ◽  
Esther Akinlabi
Keyword(s):  
High Temperature ◽  
Energy Density ◽  
Laser Beam ◽  
Laser Energy ◽  
High Energy ◽  
Phase Changes ◽  
High Energy Density ◽  
Effect Of Temperature ◽  
Beam Forming ◽  
Heating And Cooling

Laser Beam Forming (LBF) being a novel technique and non-contact manufacturing process, employs laser beam as the tool of shaping and bending metal sheets into different shapes and curvatures for various applications. LBF is a high-temperature process, where rapid heating and cooling occurs causing microstructural changes like dynamic recrystallization and phase changes. The study becomes necessary to ensure that the structural integrity of the processed material is not compromised. Hence, the investigation focuses on the effect of temperature on the developed microstructure during the LBF process. The design of experiment was considered, using three levels and five factors. The experimentally measured curvatures were validated with the predicted measured curvatures, which were found to be in agreement. The result shows that the developed ferrite and pearlite grains were due to the heating and cooling. Furthermore, the average grain sizes at a low energy density of about 355°C and high energy density of about 747°C were found to be about 10 μm and 6 μm respectively. It is implied that the high temperature from the high laser energy aided the deformation of the grains significantly. However, such high temperature must be closely monitored so to avoid metallurgical notches in the processed component.

Excimer Lasbr Induced Crystallization of thin Amorphous Si Films on SiO2: Implications of Crystallized Microstructures for Phase Transformation Mechanisms

1992 ◽  
Vol 283 ◽  
Author(s):  
H. J. Kim ◽  
James S. Im ◽  
Michael O. Thompson
Keyword(s):  
Grain Size ◽  
Energy Density ◽  
Laser Energy ◽  
High Energy ◽  
High Energy Density ◽  
Laser Energy Density ◽  
Single Shot ◽  
Average Grain Size ◽  
Si Films ◽  
Density Regime

ABSTRACTUsing planar view transmission electron microscope (TEM) and transient reflectance (TR) analyses, we have investigated the excimer laser crystallization of amorphous silicon (a-Si) films on SiO2. Emphasis was placed on characterizing the microstructures of the single-shot irradiated materials, as a function of the energy density of the laser pulse and the temperature of the substrate. The dependence of the grain size and melt duration as a function of energy density revealed two major crystallization regimes. In the low energy density regime, the average grain size first increases gradually with increases in the laser energy density. In the high energy density regime, on the other hand, a very fine grained microstructure, which is relatively insensitive to variations in the laser energy density, is obtained. In addition, we have discovered that at the transition between these two regimes an extremely small experimental window exists, within which an exceedingly large grain-sized polycrystalline film is obtained. We suggest a liquid phase growth model for this phenomenon, which is based on the regrowth of crystals from the residual solid islands at the oxide interface.

scholarly journals Effect of process parameters on the microstructure and mechanical properties of AA2024 fabricated using selective laser melting

2020 ◽  
Vol 112 (1-2) ◽  
pp. 175-192
Author(s):  
Mulla Ahmet Pekok ◽  
Rossitza Setchi ◽  
Michael Ryan ◽  
Quanquan Han ◽  
Dongdong Gu
Keyword(s):  
Mechanical Properties ◽  
Selective Laser Melting ◽  
Scanning Speed ◽  
High Energy ◽  
Incomplete Fusion ◽  
Laser Melting ◽  
Melt Pool ◽  
2024 Alloy ◽  
Manufacturing Techniques ◽  
Melt Pool Size

AbstractSelective laser melting (SLM) offers significant benefits, including geometric freedom and rapid production, when compared with traditional manufacturing techniques. However, the materials available for SLM production remain limited, restricting the industrial adoption of the technology. The mechanical properties and microstructure of many aluminium alloys have not been fully explored, as their manufacturability using SLM is extremely challenging. This study investigates the effect of laser power, hatch spacing and scanning speed on the mechanical and microstructural properties of as-fabricated aluminium 2024 alloy (AA2024) manufactured using SLM. The results reveal that almost crack-free structures with high relative density (99.9%) and Archimedes density (99.7%) have been achieved. It is shown that when using low energy density (ED) levels, large cracks and porosities are a major problem, owing to incomplete fusion; however, small gas pores are prevalent at high-energy densities due to the dissolved gas particles in the melt pool. An inversely proportional relationship between ED and microhardness has also been observed. Lower ED decreases the melt pool size and temperature gradients but increases the cooling rate, creating a fine-grained microstructure, which restricts dislocation movement, therefore increasing the microhardness. The highest microhardness (116 HV0.2), which was obtained from one of the lowest EDs used (100 J/mm3), is 45% higher than as-cast AA2024-0, but 17% lower than wrought AA2024-T6 alloy.

A Numerical Study on the Keyhole Formation During Laser Powder Bed Fusion Process

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Subin Shrestha ◽  
Y. Kevin Chou
Keyword(s):  
Energy Density ◽  
Numerical Study ◽  
High Energy ◽  
High Energy Density ◽  
Computational Domain ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool ◽  
Keyhole Behavior

The dynamic phenomenon of a melt pool during the laser powder bed fusion (LPBF) process is complex and sensitive to process parameters. As the energy density input exceeds a certain threshold, a huge vapor depression may form, known as the keyhole. This study focuses on understanding the keyhole behavior and related pore formation during the LPBF process through numerical analysis. For this purpose, a thermo-fluid model with discrete powder particles is developed. The powder distribution, obtained from a discrete element method (DEM), is incorporated into the computational domain to develop a 3D process physics model using flow-3d. The melt pool formation during the conduction mode and the keyhole mode of melting has been discerned and explained. The high energy density leads to the formation of a vapor column and consequently pores under the laser scan track. Further, the keyhole shape resulted from different laser powers and scan speeds is investigated. The numerical results indicated that the keyhole size increases with the increase in the laser power even with the same energy density. The keyhole becomes stable at a higher power, which may reduce the occurrence of pores during laser scanning.

A Numerical Study on the Keyhole Formation During Laser Powder Bed Fusion Process

2019 ◽  
Author(s):  
Subin Shrestha ◽  
Y. Kevin Chou
Keyword(s):  
Energy Density ◽  
Numerical Study ◽  
High Energy ◽  
High Energy Density ◽  
Computational Domain ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool ◽  
Keyhole Behavior

Abstract The dynamic phenomenon of a melt pool during the laser powder bed fusion (LPBF) process is complex and sensitive to process parameters. As the energy density input exceeds a certain threshold, a huge vapor depression may form, known as the keyhole. This study focuses on understanding the keyhole behavior and related pore formation during the LPBF process through numerical analysis. For this purpose, a thermo-fluid model with discrete powder particles is developed. The powder distribution, obtained from a discrete element method (DEM), is incorporated into the computational domain to develop a 3D process physics model using FLOW-3D. The melt pool formation during the conduction mode and the keyhole mode of melting has been discerned and explained. The high energy density leads to the formation of a vapor column and consequently pores under the laser scan track. Further, the keyhole shape resulted from different laser powers and scan speeds is investigated. The numerical results indicated that the keyhole size increases with the increase in the laser power even with the same energy density. The keyhole becomes stable at a higher power, which may reduce the occurrence of pores during laser scanning.

Selective Laser Melting of Mechanically Alloyed Metastable Al5Fe2 Powders

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Hugo Montiel ◽  
Ben Xu ◽  
Jianzhi Li
Keyword(s):  
Aluminum Alloys ◽  
Energy Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Laser Scanning ◽  
Laser Energy ◽  
Scanning Speed ◽  
High Energy ◽  
Laser Energy Density ◽  
Laser Melting

Aluminum alloys, which are high-strength lightweight materials, were processed by selective laser melting (SLM) with high-energy consumption and poor finish due to quick heat dissipation. Previous investigations reported that SLM with 300 W laser power and 500 mm/s scanning speed can process the aluminum alloys, such as Al-Si12 and AlSi10Mg. This work aims to process the powders to alter their properties and to reduce the laser intensity required in the process, and it also reports that the SLM-processed Al–Fe alloys utilize the metastable alloy by mechanical alloying (MA). The elemental Al and Fe powders were first alloyed in a ball mill in a relative short time period (∼15 h) employing high milling intensities, high ball-to-powder ratio (≥20:1), and high milling velocities (≥400 rpm), which produced fine metastable Al–Fe powders, and these powders were processed later by the SLM. The optimum laser power, the scanning speed, hatch distance, and substrate temperature were investigated by a series of experiments. Experimental results indicated that decreasing the laser energy density while increasing the laser scanning speed can benefit for smoother laser hatch lines, and the metastable Al5Fe2 alloy powders can be processed and stabilized under a 200-W laser energy density and a scanning speed of 1000 mm/s. It is expected that the combination of pre-excited materials in a metastable phase will open a new window to optimize the SLM process for aluminum alloys and other metallic alloys.

A HIGH ENERGY DENSITY ZINC/OXYGEN BATTERY SYSTEM

1966 ◽  
Author(s):  
S. CHODOSH ◽  
E. KATSOULIS ◽  
M. ROSANSKY
Keyword(s):  
Energy Density ◽  
High Energy ◽  
High Energy Density ◽  
Battery System
Sign in / Sign up

Export Citation Format

Share Document