scholarly journals Effect of LiNO3 on Expansion of Alkali–Silica Reaction in Rock Prisms and Concrete Microbars Prepared by Sandstone

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1150 ◽  
Author(s):  
Jinxin Liu ◽  
Lanqing Yu ◽  
Min Deng
Keyword(s):  
Electron Microscope ◽  
Critical Concentration ◽  
Stress Test ◽  
Molar Ratio ◽  
Alkali Silica Reaction ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Long Period ◽  
Scanning Electron

The aim of this research is to investigate the effect of LiNO3 on the alkali–silica reaction (ASR) expansion of reactive sandstone and the mechanism through which this occurs. This paper presents the results from tests carried out on rock prisms and concrete microbars prepared by sandstone and LiNO3. The findings show that LiNO3 does not decrease the expansion of these samples unless the molar ratio of [Li]/[Na + K] exceeds 1.66, and the expansion is greatly increased when its concentration is below this critical concentration. The expansion stress test proves that Li2SiO3 is obviously expansive. X-ray diffraction (XRD) and scanning electron microscope (SEM) results indicate that LiNO3 reacts with the microcrystalline quartz inside sandstone, inhibiting the formation of ASR gel, and the formation of Li2SiO3 causes larger expansion. A high concentration of LiNO3 might inhibit the ASR reaction in the early stages, and the formation of Li2SiO3 causes expansion and cracks in concrete after a long period of time.

Synthesis of MgAl2O4-SiAlON Composite Powders by Carbothermal Nitritdation of Forsterite and Alumina

2013 ◽  
Vol 634-638 ◽  
pp. 2388-2391 ◽  
Author(s):  
Hong Juan Duan ◽  
Hong Xi Zhu ◽  
Cheng Ji Deng ◽  
Wen Jie Yuan ◽  
Ping Liang
Keyword(s):  
Electron Microscope ◽  
Carbon Black ◽  
Scanning Electron Microscope ◽  
Nitrogen Atmosphere ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Composite Powders ◽  
X Ray ◽  
Scanning Electron

In this paper, the synthesis of MgAl2O4-SiAlON composite powders by forsterite, alumina and carbon black was studied. The samples were calcined under nitrogen atmosphere at 1500 °C, 1600 °C, 1650 °C for 3 hrs respectively. The phase compositions and microstructure of the synthesized powders were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM). The result shows that an optimal alumina/forsterite content was a molar ratio of 2.0:1.0, the products consisted mainly of MgAl2O4 and Si3Al3O3N5 at 1500 °C, MgAl2O4 and Mg1.25Si1.25Al2.5O3N3 at 1600 °C and 1650 °C. The temperature can improve the formation of the octahedral spinel and flakiness Mg1.25Si1.25Al2.5O3N3.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

Effect of the Neodymium Content on Mechanical Properties of the Electro-Brush Plated Nano-Al2O3/Ni Composite Coating

2012 ◽  
Vol 525-526 ◽  
pp. 277-280
Author(s):  
Guo Jin ◽  
Xiu Fang Cui ◽  
Er Bao Liu ◽  
Qing Fen Li
Keyword(s):  
Mechanical Properties ◽  
Rare Earth ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Composite Coating ◽  
Nanoindentation Test ◽  
X Ray Diffraction ◽  
X Ray ◽  
Small Cracks ◽  
Scanning Electron

The effect of the neodymium content on mechanical properties of the electro-brush plated nanoAl2O3/Ni composite coating was investigated in this paper. The microstructure and phase structure were studied with scanning electron microscope (SEM) and X-ray diffraction (XRD). The hardness and abrasion properties of several coatings with different neodymium content were studied by nanoindentation test and friction / wear experiment. Results show that the coatings are much finer and more compact when the neodymium was added, and the hardness and abrasion property of the coatings with neodymium were improved obviously. Besides, the small cracks conduced by the upgrowth stress in the coatings were ameliorated when the rare earth neodymium was added. The improvement mechanism was further discussed.

Effect of Briquetting Pressure on the Performance of In Situ Formed Sialon in Al2O3-C Refractory Bricks

2014 ◽  
Vol 881-883 ◽  
pp. 1049-1052 ◽  
Author(s):  
Nai Peng ◽  
Cheng Ji Deng ◽  
Hong Xi Zhu
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
X Ray ◽  
Z Value ◽  
Refractory Bricks ◽  
Scanning Electron

In this paper, the effects of briquetting pressure on the performance of in-situ formed Sialon in Al2O3-C refractory bricks are investigated. The phase compositions and microstructure of the Al2O3-C refractory were investigated by X-ray diffraction (XRD) and scanning electron microscope (SEM).The results show the briquetting pressure hardly has effect on the phase of the sintered specimens, two new phases of Sialon with a Z value of 2 and SiC formed. The micrographs of Sialon crystals have the shape of both column and tabular column, but with a cone tip in the specimens sintered at 200MPa and 300MPa and smooth tip in specimens sintered at 400MPa and 500MPa.

Ionic regulation and buoyancy in some planktonic organisms

1993 ◽  
Vol 73 (1) ◽  
pp. 15-23 ◽  
Author(s):  
C. Newton ◽  
W. T. W. Potts
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
The Body ◽  
Coelomic Fluid ◽  
Ionic Regulation ◽  
High Concentration ◽  
Emission Analysis ◽  
X Ray ◽  
Scanning Electron ◽  
Gastrovascular System

Magnesium/chlorine and sulphur/chlorine ratios have been measured in the body fluids of some planktonic organisms by x-ray emission analysis of frozen hydrated specimens in a scanning electron microscope. Homarus vulgaris (Anthropoda: Decapoda) larvae excluded Mg2+ and SO42-ions from the haemolymph, but to a lesser extent than does the adult lobster. Bipinnaria larvae of Asterias (Echinodermata) excluded Mg2+ and SO42-ions from the coelomic fluid. Obelia medusae excluded Mg2+ and SO42-ions from the mesogloea but concentrate them in the gastrovascular system. The high concentration of sulphate in the gastrovascular fluid of medusae has been confirmed by rhodizonate titration in Cyanea and Rhizostoma jellyfish. Some implications of magnesium and sulphate regulation are discussed.

Application of vermiculite and limestone to desulphurization and to the removal of dust during briquette combustion

2003 ◽  
Vol 67 (6) ◽  
pp. 1243-1251 ◽  
Author(s):  
A. Lu ◽  
D. Zhao ◽  
J. Li ◽  
C. Wang ◽  
S. Qin
Keyword(s):  
Electron Microscopy ◽  
Coal Combustion ◽  
Combustion Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Retention Ratio ◽  
X Ray ◽  
Major Factors ◽  
Chemical Reactant ◽  
Scanning Electron

AbstractSmall domestic cooking furnaces are widely used in China. These cooking furnaces release SO2 gas and dust into the atmosphere and cause serious air pollution. Experiments were conducted to investigate the effects of vermiculite, limestone or CaCO3, and combustion temperature and time on desulphurization and dust removal during briquette combustion in small domestic cooking furnaces. Additives used in the coal are vermiculite, CaCO3 and bentonite. Vermiculite is used for its expansion property to improve the contact between CaCO3 and SO2 and to convey O2 into the interior of briquette; CaCO3 is used as a chemical reactant to react with SO2 to form CaSO4; and bentonite is used to develop briquette strength. Expansion of vermiculite develops loose interior structures, such as pores or cracks, inside the briquette, and thus brings enough oxygen for combustion and sulphation reaction. Effective combustion of the original carbon reduces amounts of dust in the fly ash. X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray analysis show that S exists in the ash only as anhydrite CaSO4, a product of SO2 reacting with CaCO3 and O2. The formation of CaSO4 effectively reduces or eliminates SO2 emission from coal combustion. The major factors controlling S retention are vermiculite, CaCO3 and combustion temperature. The S retention ratio increases with increasing vermiculite amount at 950°C. The S retention ratio also increases with increasing Ca/S molar ratio, and the best Ca/S ratio is 2-3 for most combustion. With 12 g of the original coal, 1 to 2 g of vermiculite, a molar Ca/S ratio of 2.55 by adding CaCO3, and some bentonite, a S retention ratio >65% can be readily achieved. The highest S retention ratio of 97.9% is achieved at 950°C with addition of 2 g of vermiculite, a Ca/S ratio of 2.55 and bentonite.

Solvothermal Synthesis of Bi2Se3 Hexagonal Nanosheet Crystals

2011 ◽  
Vol 236-238 ◽  
pp. 1712-1716 ◽  
Author(s):  
Hai Tao Liu ◽  
Jun Dai ◽  
Jia Jia Zhang ◽  
Wei Dong Xiang
Keyword(s):  
Electron Microscope ◽  
Solvothermal Synthesis ◽  
Solvothermal Method ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
Uniform Size ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Scanning Electron

Bismuth selenide (Bi2Se3) hexagonal nanosheet crystals with uniform size were successfully prepared via a solvothermal method at 160°C for 22 h using bismuth trichloride(BiCl3) and selenium powder(Se) as raw materials, sodium bisulfite(NaHSO3) as a reducing agent, diethylene glycol(DEG) as solvent, and ammonia as pH regulator. Various techniques such as X-ray diffraction (XRD), field-emission scanning electron microscope (FESEM), high-resolution transmission electron microscope (HRTEM), and selected area electron diffraction (SAED) were used to characterize the obtained products. Results show that the as-synthesized samples are pure Bi2Se3 hexagonal nanosheet crystals. A possible growth mechanism for Bi2Se3 hexagonal nanosheet crystals is also discussed based on the experiment.

Effect of P2O5 on the Properties of Alite-Calcium Strontium Sulphoaluminate Cement

2011 ◽  
Vol 306-307 ◽  
pp. 961-965
Author(s):  
Chao Nan Yin ◽  
Ling Chao Lu ◽  
Shou De Wang
Keyword(s):  
Compressive Strength ◽  
Electron Microscope ◽  
Heat Evolution ◽  
Petrographic Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sulphoaluminate Cement ◽  
Suitable Amount ◽  
Acceleration Period ◽  
Scanning Electron

The influence of P2O5on the properties of alite-calcium strontium sulphoaluminate cement was researched by means of X-ray diffraction, scanning electron microscope-energy dispersive spectroscopy (SEM-EDS) and petrographic analysis. The results show that the optimal content of P2O5is 0.3% and the compressive strength of the cement at 1, 3, 28d are 27.0, 59.1, 110.9MPa when the calcining temperature is 1350°C. P2O5mainly exists in the belite and a suitable amount of P2O5can promote the formation of C1.5Sr2.5A3and alite. When the content of P2O5is higher than 0.3%, the formation of C1.5Sr2.5A3and alite can be hindered. P2O5can enhance the hydration heat evolution rate in the acceleration period and the hydrate heat of cement containing P2O5increases slightly.

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

2012 ◽  
Vol 620 ◽  
pp. 384-388
Author(s):  
Sharifah Aishah Syed Salim ◽  
Julie Juliewatty Mohamed ◽  
Zainal Arifin Ahmad ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Powder Mixture ◽  
Raw Material ◽  
Inert Gas ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Elemental Powder Mixture ◽  
Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

Sign in / Sign up

Export Citation Format

Share Document