scholarly journals Preparation of Fibrillated Cellulose Nanofiber from Lyocell Fiber and Its Application in Air Filtration

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1313 ◽  
Author(s):  
Jin Long ◽  
Min Tang ◽  
Yun Liang ◽  
Jian Hu
Keyword(s):  
Pressure Drop ◽  
Filter Paper ◽  
Figure Of Merit ◽  
Cellulose Nanofibers ◽  
Cellulose Nanofiber ◽  
Dramatic Improvement ◽  
Air Filtration ◽  
Air Filter ◽  
Lyocell Fiber ◽  
Filter Papers

Ambient particulate matter less than 2.5 μm (PM2.5) can substantially degrade the performance of cars by clogging the air intake filters. The application of nanofibers in air filter paper can achieve dramatic improvement of filtration efficiency with low resistance to air flow. Cellulose nanofibers have gained increasing attention because of their biodegradability and renewability. In this work, the cellulose nanofiber was prepared by Lyocell fiber nanofibrillation via a PFI-type refiner, and the influence of applying a cellulose nanofiber on filter paper was investigated. It was found that the cellulose nanofibers obtained under 1.00 N/mm and 40,000 revolutions were mainly macrofibrils of Lyocell fiber with average fiber diameter of 0.8 µm. For the filter papers with a different nanofiber fraction, both the pressure drop and fractional efficiency increased with the higher fraction of nanofibers. The results of the figure of merit demonstrated that for particles larger than 0.05 µm, the figure of merit increased substantially with a 5% nanofiber, but decreased when the nanofiber fraction reached 10% and higher. It was concluded that the optimal fraction of the cellulose nanofiber against PM2.5 was 5%. The results of the figure of merit were related to the inhomogeneous distribution of nanofibers in the fibrous structure. The discrepancy of the theoretical and measured pressure drop showed that a higher nanofiber fraction led to a higher degree of fiber inhomogeneity.

Flexible hydroxyapatite ultralong nanowire-based paper for highly efficient and multifunctional air filtration

2017 ◽  
Vol 5 (33) ◽  
pp. 17482-17491 ◽  
Author(s):  
Zhi-Chao Xiong ◽  
Ri-Long Yang ◽  
Ying-Jie Zhu ◽  
Fei-Fei Chen ◽  
Li-Ying Dong
Keyword(s):  
Pressure Drop ◽  
Filter Paper ◽  
Low Pressure ◽  
Air Filtration ◽  
Air Filter ◽  
Highly Efficient ◽  
Removal Efficiencies

Ultralong hydroxyapatite nanowire-based air filter paper with a low pressure drop and high removal efficiencies for PM2.5 and PM10 has been developed.

Prediction of air filter efficiency and pressure drop in air filtration media using a stochastic simulation

2008 ◽  
Vol 9 (1) ◽  
pp. 34-38 ◽  
Author(s):  
Xinpeng Wang ◽  
Kitai Kim ◽  
Changhwan Lee ◽  
Jooyong Kim
Keyword(s):  
Pressure Drop ◽  
Stochastic Simulation ◽  
Air Filtration ◽  
Air Filter ◽  
Filter Efficiency

Branched nanofibers with tiny diameters for air filtration via one-step electrospinning

2020 ◽  
pp. 152808372092377
Author(s):  
Bilal Zaarour ◽  
Hussen Tina ◽  
Lei Zhu ◽  
XiangYu Jin
Keyword(s):  
Sodium Chloride ◽  
Pressure Drop ◽  
Polyvinylidene Fluoride ◽  
Filtration Efficiency ◽  
Air Filtration ◽  
Air Filter ◽  
One Step ◽  
Tetrabutylammonium Chloride ◽  
Filtration Properties ◽  
Branched Structure

Engineering the surface morphology of fibers has been attracting significant consideration in various areas and applications. In this study, polyvinylidene fluoride (PVDF) branched nanofibers with a diameter of less than 50 nm are electrospun directly at a low relative humidity by adding tetrabutylammonium chloride. The effects of the branched structure on the specific surface area and pore size distribution are investigated, and the filtration properties of the air filter based on branched nanofiber webs with different basis weights are studied. The results exhibit that the air filter based on PVDF branched nanofibers with the basis weight of 1 g/m2 has an outstanding filtration efficiency (99.999%) to 0.26 µm sodium chloride particles under the pressure drop of 126.17 Pa. We believe that this study can be used as a useful reference for the preparation of branched nanofibers through one-step electrospinning.

Pressure drop, penetration and quality factor of filter paper containing nanofibers

2016 ◽  
Vol 87 (4) ◽  
pp. 498-508 ◽  
Author(s):  
Min Tang ◽  
Jian Hu ◽  
Yun Liang ◽  
David YH Pui
Keyword(s):  
Pressure Drop ◽  
Quality Factor ◽  
Filter Paper ◽  
Modeling Method ◽  
Fibrous Structure ◽  
Fibrous Filter Media ◽  
Fine Fiber ◽  
Coarse Fibers ◽  
Filter Papers ◽  
Fiber Filter

Nanofiber has shown outstanding performance in many studies. Blending nanofibers into fibrous filter media is a promising way to improve the filtration performance. This paper discussed the modeling method for multi-fiber filter paper and the proper way to apply nanofiber into filter paper. Sixteen different filter papers were prepared and these filter papers covered the range of coarse-fiber-dominant and fine-fiber-dominant fibrous structure. The theoretical modeling method in this study for pressure drop and penetration of multi-fiber filter paper showed accurate results compared with the experiment data. It was found that for the higher quality factor, the nanofibers should be effectively separated by the coarse fibers. This study presented the idea of the fiber's effective contribution to filtration efficiency, which can lead to a comprehensive and distinct understanding of fibrous structure and filtration properties.

Liquid-mediated particle capture by nonwoven filter media for automotive engine intake air filtration

2021 ◽  
pp. 152808372110610
Author(s):  
Shivendra Yadav ◽  
Dipayan Das
Keyword(s):  
Pressure Drop ◽  
Polypropylene Fiber ◽  
Nonwoven Fabric ◽  
Filtration Efficiency ◽  
Engine Oil ◽  
Air Filtration ◽  
Dust Deposition ◽  
Filter Media ◽  
Air Filter ◽  
Automotive Engine

This article reports on development, characterization, and performance of liquid-treated nonwoven air filter media for automotive engine intake application. A polypropylene fiber-based needle-punched nonwoven fabric was prepared for treatment with four viscous liquids (glycerol, SAE 20W/50 engine oil, PEG 400, and deionized water) by liquid spraying technique. The filtration performance was evaluated in terms of initial and final gravimetric filtration efficiencies, fractional filtration efficiency, evolution of pressure drop, and dust holding capacity. The liquid-treated filter media registered higher gravimetric as well as fractional filtration efficiency and higher dust holding capacity as compared to the untreated ones. The initial and final gravimetric filtration efficiencies were found to be directly related to liquid add-on via a power law relationship. The liquid-treated filter media also exhibited higher fractional filtration efficiency than their untreated counterparts for all sizes of tested particles. Interestingly, the increase of fractional efficiency was more for smaller particles as compared to larger ones. This was explained quantitatively through single fiber efficiency due to adhesion. The viscosity of liquid was found to be a very crucial parameter as the dust deposition morphology was contingent to the flow of liquid onto the filter media. The stickiest liquid yielded highest filtration efficiencies, displayed slowest rise of pressure drop, and exhibited highest dust holding capacity.

scholarly journals Air filtration improvement of konjac glucomannan-based aerogel air filters through physical structure design

2021 ◽  
Author(s):  
Hong Qian ◽  
Ying Fang ◽  
Kao Wu ◽  
Hao Wang ◽  
Bin Li ◽  
...  
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Surface Area ◽  
Physical Structure ◽  
Structure Design ◽  
Air Filtration ◽  
Air Filters ◽  
Air Filter ◽  
Purification Time

Abstract This study presents two methods to improve the air filtration performance of konjac glucomannan (KGM)-based aerogel air filters through physical structure design by changing the pore-size distribution and the surface area, using an air purifier. Results indicated that KGM-based aerogels had a comparable filtration effect with the commercial air filter with a longer purification time. This purification time could be shortened by over 50%, by changing the pore-size distribution from large size to small size or increase the surface area with the fold structure. This should boost the development of polysaccharide-based aerogel used as the air filter.

scholarly journals Well-Dispersed Silver Nanoparticles on Cellulose Filter Paper for Bacterial Removal

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 595
Author(s):  
Hsiu-Wen Chien ◽  
Ming-Yen Tsai ◽  
Chia-Jung Kuo ◽  
Ching-Lo Lin
Keyword(s):  
Silver Nanoparticles ◽  
Filter Paper ◽  
X Ray Diffraction ◽  
Bacterial Reduction ◽  
Treatment Technology ◽  
Bacterial Removal ◽  
Contaminated Drinking Water ◽  
Gravity Driven ◽  
Filter Papers ◽  
Cellulose Filter

In this study, a polydopamine (PDA) and polyethyleneimine (PEI)-assisted approach was developed to generate well-distributed PDA/PEI/silver (PDA/PEI/Ag) nanocomplexes on the surfaces of commercial cellulose filter papers to achieve substantial bacterial reduction under gravity-driven filtration. PDA can bind to cellulose paper and act as a reducer to produce silver nanoparticles (AgNPs), while PEI can react with oxidative dopamine and act as a dispersant to avoid the aggregation of AgNPs. The successful immobilization of PDA/PEI/Ag nanocomplexes was confirmed by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) were used as pathogen models to test the efficacy of the PDA/PEI/Ag nanocomplex-incorporated filter papers. The PDA/PEI/Ag nanocomplex-incorporated filter papers provided a substantial bacterial removal of up to 99% by simple gravity filtration. This work may be useful to develop a feasible industrial production process for the integration of biocidal AgNPs into cellulose filter paper and is recommended as a local-condition water-treatment technology to treat microbial-contaminated drinking water.

Evolution of Gas Turbine Intake Air Filtration in a 420 MW Cogeneration Plant

2014 ◽  
Author(s):  
Steve Ingistov ◽  
Michael Milos ◽  
Rakesh K. Bhargava
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Economic Benefits ◽  
Cogeneration Plant ◽  
Air Filtration ◽  
Air Filter ◽  
Filter System ◽  
Turbine Performance ◽  
Filtration System ◽  
Operational Data

A suitable inlet air filter system is required for a gas turbine, depending on installation site and its environmental conditions, to minimize contaminants entering the compressor section in order to maintain gas turbine performance. This paper describes evolution of inlet air filter systems utilized at the 420 MW Watson Cogeneration Plant consisting of four GE 7EA gas turbines since commissioning of the plant in November 1987. Changes to the inlet air filtration system became necessary due to system limitations, a desire to reduce operational and maintenance costs, and enhance overall plant performance. Based on approximately 2 years of operational data with the latest filtration system combined with other operational experiences of more than 25 years, it is shown that implementation of the high efficiency particulate air filter system provides reduced number of crank washes, gas turbine performance improvement and significant economic benefits compared to the traditional synthetic media type filters. Reasons for improved gas turbine performance and associated economic benefits, observed via actual operational data, with use of the latest filter system are discussed in this paper.

scholarly journals Study on Synthesis and Photocatalytic Activity of Porous Titania Nanotubes

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Huang Liu ◽  
Yanhua Zhang ◽  
Hongtao Yang ◽  
Wei Xiao ◽  
Lanlan Sun
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Filter Paper ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Cellulose Nanofibers ◽  
Titania Nanotubes ◽  
Tetrabutyl Titanate ◽  
X Ray ◽  
Porous Titania

Using the common natural cellulose substance (filter paper) and triblock copolymer (Pluronic P123) micelles as dual templates, porous titania nanotubes with enhanced photocatalytic activity have been successfully synthesized through sol-gel methods. Firstly, P123 micelles were adsorbed onto the surfaces of cellulose nanofibers of filter paper, followed by hydrolysis and condensation of tetrabutyl titanate around these micelles to form titania layer. After calcination to remove the organic templates, hierarchical titania nanotubes with pores in the walls were obtained. The sample was characterized by X-ray diffraction pattern (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption/desorption, Fourier Transform Infrared Spectroscopy (FT-IR), Ultraviolet-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), and X-ray photoelectron spectroscopy (XPS). As compared with commercial P25 catalyst, the porous titania nanotubes prepared by this method displayed significantly enhanced photocatalytic activity for degrading methyl orange under UV irradiation. Within 10 minutes, the porous titania nanotubes are able to degrade over 70% of the original MO, while the value for the commercial Degussa P25 is only about 33%.

Sign in / Sign up

Export Citation Format

Share Document