scholarly journals Wave Energy Converter Power Take-Off System Scaling and Physical Modelling

2020 ◽  
Vol 8 (9) ◽  
pp. 632
Author(s):  
Gianmaria Giannini ◽  
Irina Temiz ◽  
Paulo Rosa-Santos ◽  
Zahra Shahroozi ◽  
Victor Ramos ◽  
...  
Keyword(s):  
Wave Energy ◽  
Experimental Testing ◽  
Experimental Studies ◽  
Physical Modelling ◽  
Cost Effective ◽  
Estimation Methods ◽  
Small Scale ◽  
Wave Power ◽  
Energy Converter ◽  
Energy Device

Absorbing wave power from oceans for producing a usable form of energy represents an attractive challenge, which for the most part concerns the development and integration, in a wave energy device, of a reliable, efficient and cost-effective power take-off mechanism. During the various stages of progress, for assessing a wave energy device, it is convenient to carry out experimental testing that, opportunely, takes into account the realistic behaviour of the power take-off mechanism at a small scale. To successfully replicate and assess the power take-off, good practices need to be implemented aiming to correctly scale and evaluate the power take-off mechanism and its behaviour. The present paper aims to explore and propose solutions that can be applied for reproducing and assessing the power take-off element during experimental studies, namely experimental set-ups enhancements, calibration practices, and error estimation methods. A series of recommendations on how to practically organize and carry out experiments were identified and three case studies are briefly covered. It was found that, despite specific options that can be strictly technology-dependent, various recommendations could be universally applicable.

scholarly journals A broadbanded pressure differential wave energy converter based on dielectric elastomer generators

2021 ◽  
Author(s):  
Michele Righi ◽  
Giacomo Moretti ◽  
David Forehand ◽  
Lorenzo Agostini ◽  
Rocco Vertechy ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Deformations ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Pressure Differential ◽  
Design Stage ◽  
Small Scale ◽  
Energy Converter ◽  
Wide Range ◽  
The Waves

AbstractDielectric elastomer generators (DEGs) are a promising option for the implementation of affordable and reliable sea wave energy converters (WECs), as they show considerable promise in replacing expensive and inefficient power take-off systems with cheap direct-drive generators. This paper introduces a concept of a pressure differential wave energy converter, equipped with a DEG power take-off operating in direct contact with sea water. The device consists of a closed submerged air chamber, with a fluid-directing duct and a deformable DEG power take-off mounted on its top surface. The DEG is cyclically deformed by wave-induced pressure, thus acting both as the power take-off and as a deformable interface with the waves. This layout allows the partial balancing of the stiffness due to the DEG’s elasticity with the negative hydrostatic stiffness contribution associated with the displacement of the water column on top of the DEG. This feature makes it possible to design devices in which the DEG exhibits large deformations over a wide range of excitation frequencies, potentially achieving large power capture in a wide range of sea states. We propose a modelling approach for the system that relies on potential-flow theory and electroelasticity theory. This model makes it possible to predict the system dynamic response in different operational conditions and it is computationally efficient to perform iterative and repeated simulations, which are required at the design stage of a new WEC. We performed tests on a small-scale prototype in a wave tank with the aim of investigating the fluid–structure interaction between the DEG membrane and the waves in dynamical conditions and validating the numerical model. The experimental results proved that the device exhibits large deformations of the DEG power take-off over a broad range of monochromatic and panchromatic sea states. The proposed model demonstrates good agreement with the experimental data, hence proving its suitability and effectiveness as a design and prediction tool.

scholarly journals A Low-Cost Motion Capture System for Small-Scale Wave Energy Device Tank Testing

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
Francesco Paparella ◽  
Satja Sivcev ◽  
Daniel Toal ◽  
John V. Ringwood
Keyword(s):  
Wave Energy ◽  
Motion Tracking ◽  
Tracking System ◽  
Low Cost ◽  
Measurement Unit ◽  
Small Scale ◽  
Energy Device ◽  
Optical Motion ◽  
Optical Motion Tracking ◽  
Motion Tracking System

The measurement of the motion of a small-scale wave energy device during wave tank tests is important for the evaluation of its response to waves and the assessment of power production. Usually, the motion of a small-scale wave energy converter (WEC) is measured using an optical motion tracking system with high precision and sampling rate. However, the cost for an optical motion tracking system can be considerably high and, therefore, the overall cost for tank testing is increased. This paper proposes a low-cost capture system composed of an inertial measurement unit and ultrasound sensors. The measurements from the ultrasound sensors are combined optimally with the measurements from the inertial measurement unit through an extended Kalman filter (EKF) in order to obtain an accurate estimation of the motion of a WEC.

scholarly journals Experimental Analysis of a Novel Adaptively Counter-Rotating Wave Energy Converter for Powering Drifters

2019 ◽  
Vol 7 (6) ◽  
pp. 171 ◽  
Author(s):  
Guoheng Wu ◽  
Zhongyue Lu ◽  
Zirong Luo ◽  
Jianzhong Shang ◽  
Chongfei Sun ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Irregular Waves ◽  
Surface Velocity ◽  
Small Scale ◽  
Power Constraint ◽  
Energy Converter ◽  
Wave Tank ◽  
Wide Range ◽  
Rotating Wave

Nowadays, drifters are used for a wide range of applications for researching and exploring the sea. However, the power constraint makes it difficult for their sampling intervals to be smaller, meaning that drifters cannot transmit more accurate measurement data to satellites. Furthermore, due to the power constraint, a modern Surface Velocity Program (SVP) drifter lives an average of 400 days before ceasing transmission. To overcome the power constraint of SVP drifters, this article proposes an adaptively counter-rotating wave energy converter (ACWEC) to supply power for drifters. The ACWEC has the advantages of convenient modular integration, simple conversion process, and minimal affection by the crucial sea environment. This article details the design concept and working principle, and the interaction between the wave energy converter (WEC) and wave is presented based on plane wave theory. To verify the feasibility of the WEC, the research team carried out a series of experiments in a wave tank with regular and irregular waves. Through experiments, it was found that the power and efficiency of the ACWEC are greatly influenced by parameters such as wave height and wave frequency. The maximum output power of the small scale WEC in a wave tank is 6.36 W, which allows drifters to detect ocean data more frequently and continuously.

A Joint Numerical and Experimental Study of a Surging Point Absorbing Wave Energy Converter (WRASPA)

2009 ◽  
Author(s):  
Majid A. Bhinder ◽  
Clive G. Mingham ◽  
Derek M. Causon ◽  
Mohammad T. Rahmati ◽  
George A. Aggidis ◽  
...  
Keyword(s):  
Wave Energy ◽  
Informed Choice ◽  
Wave Energy Converter ◽  
Body Motion ◽  
Numerical Dissipation ◽  
Small Scale ◽  
Linear Wave ◽  
Energy Converter ◽  
Non Linear ◽  
Experimental Project

This paper presents the findings from using several commercial computational fluid dynamics codes in a joint numerical and experimental project to simulate WRASPA, a new wave energy converter (WEC) device. A series of fully 3D non-linear simulations of WRASPA are presented. Three commercial codes STAR-CCM, CFX and FLOW-3D are considered for simulating the WRASPA device and final results are presented based on the use of Flow-3D. Results are validated by comparison to experimental data obtained from small scale tank tests undertaken at Lancaster University (LU). The primary aim of the project is to use numerical simulation to optimize the collector geometry for power production over a range of likely wave climates. A secondary aim is to evaluate the ability of commercial codes to simulate rigid body motion in linear and non-linear wave climates in order to choose the optimal code with respect to compute speed and ease of problem setup. Issues relating to the ability of a code in terms of numerical dissipation of waves, wave absorption, wave breaking, grid generation and moving bodies will all be discussed. The findings of this paper serve as a basis for an informed choice of commercial package for such simulations. However the capability of these commercial codes is increasing with every new release.

Design and Potential Application of Small Scale Wave Energy Converter

2017 ◽  
Author(s):  
Tunde O. Aderinto ◽  
Francisco Haces-Fernandez ◽  
Hua Li
Keyword(s):  
Wave Energy ◽  
Energy Production ◽  
Energy Resource ◽  
Appropriate Technology ◽  
Wave Energy Converter ◽  
Small Scale ◽  
Ocean Energy ◽  
Energy Converter ◽  
Wave Energy Converters ◽  
Wave Properties

Although theoretical available wave energy is higher than most of ocean energy sources, the commercial utilization of wave energy is much slower than other ocean energy sources. The difficulty of integration with the electrical grid system and the challenges of the installation, operation and maintenance of large energy generation and transmission systems are the major reasons. Even though there are successfully tested models of wave energy converters, the fact that wave energy is directly affected by wave height and wave period makes the actual wave energy output with high variation and difficult to be predicted. And most of the previous studies on wave energy and its utilization have focused on the large scale energy production that can be integrated into a power grid system. In this paper, the authors identify and discuss stand-alone wave energy converter systems and facilities that are not connected to the electricity grid with focus on small scale wave energy systems as potential source of energy. For the proper identification, qualification and quantification of wave energy resource potential, wave properties such as wave height and period need to be characterized. This is used to properly determine and predict the probability of the occurrence of these wave properties at particular locations, which enables the choice of product design, installation, operation and maintenance to effectively capture wave energy. Meanwhile, the present technologies available for wave energy converters can be limited by location (offshore, nearshore or shoreline). Therefore, the potential applications of small scale stand-alone wave energy converter are influenced by the demand, location of the need and the appropriate technology to meet the identified needs. The paper discusses the identification of wave energy resource potentials, the location and appropriate technology suitable for small scale wave energy converter. Two simplified wave energy converter designs are created and simulated under real wave condition in order to estimate the energy production of each design.

scholarly journals Using Flexible Blades to Improve the Performance of Novel Small-Scale Counter-Rotating Self-Adaptable Wave Energy Converter for Unmanned Marine Equipment

2019 ◽  
Vol 7 (7) ◽  
pp. 223 ◽  
Author(s):  
Sun ◽  
Shang ◽  
Luo ◽  
Lu ◽  
Wu ◽  
...  
Keyword(s):  
Output Power ◽  
Wave Energy ◽  
Power Supply ◽  
Simulation Analysis ◽  
Average Power ◽  
Wave Energy Converter ◽  
Small Scale ◽  
Energy Converter ◽  
Experimental Conditions ◽  
Blade Thickness

Unmanned marine equipment has been increasingly developed for open seas. The lack of efficient and reliable power supply is currently one of the bottlenecks restricting the practical application of these devices. In order to provide a viable power supply method for unmanned marine equipment, such as sonic buoys and sea robots, we originally propose a novel small-scale flexible blade wave energy converter (WEC) based on self-adaptable counter-rotating operation mechanism. The flexible blade WEC is designed on the basis of the rigid blade WEC with the caging device. This paper identifies the key factors affecting WEC performance through theoretical analysis. According to the numerical simulation analysis, the output mechanical power of the double-layer absorber is 12.8 W, and the hydraulic efficiency is 36.3%. The results of the verification experiment show that the peak power of WEC is 5.8 W and the average power is 3.2 W. The WEC with 65Mn flexible blade under most experimental conditions has the best performance when the blade thickness is 0.10 mm. The study shows that the new generation WEC can effectively overcome the excessive fluctuation of the output power of the previous generation WEC. The output power curve of the novel WEC is relatively smooth, which is conducive to its smooth operation and subsequent utilization and storage of electrical energy.

Non-linear numerical modeling and experimental testing of a point absorber wave energy converter

2014 ◽  
Vol 78 ◽  
pp. 11-21 ◽  
Author(s):  
A.S. Zurkinden ◽  
F. Ferri ◽  
S. Beatty ◽  
J.P. Kofoed ◽  
M.M. Kramer
Keyword(s):  
Numerical Modeling ◽  
Wave Energy ◽  
Experimental Testing ◽  
Wave Energy Converter ◽  
Energy Converter ◽  
Point Absorber ◽  
Non Linear

Comparison of Mooring Loads in Survivability Mode on the Wave Dragon Wave Energy Converter Obtained by a Numerical Model and Experimental Data

2012 ◽  
Author(s):  
Stefano Parmeggiani ◽  
Made Jaya Muliawan ◽  
Zhen Gao ◽  
Torgeir Moan ◽  
Erik Friis-Madsen
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Complex Geometry ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Coupled Analysis ◽  
Small Scale ◽  
Energy Converter ◽  
Numerical Predictions ◽  
Small Scale Model

The Wave Dragon Wave Energy Converter is ready to be up-scaled to commercial size. The design and feasibility analysis of a 1.5 MW pre-commercial unit to be deployed at the DanWEC test center in Hanstholm, Denmark, is currently ongoing. With regard to the mooring system, the design has to be carried out numerically, through coupled analyses of alternative solutions. The present study deals with the preliminary hydrodynamic characterization of Wave Dragon needed in order to calibrate the numerical model to be used for the mooring design. A hydrodynamic analysis of the small scale model in the frequency domain is performed by the software HydroD, which uses WAMIT as core software. The quadratic damping term, accounting for the viscous effect, is determined through an iterative procedure aimed at matching numerical predictions on the mooring tension, derived through time domain coupled analysis, with experimental results derived from tank tests of a small scale model. Due to the complex geometry of the device, a sensitivity analysis is performed to discuss the influence of the mean position on the quality of the numerical predictions. Good correspondence is achieved between the experimental and numerical model. The numerical model is hence considered reliable for future design applications.

scholarly journals Round Robin Testing: Exploring Experimental Uncertainties through a Multifacility Comparison of a Hinged Raft Wave Energy Converter

2021 ◽  
Vol 9 (9) ◽  
pp. 946
Author(s):  
Thomas Davey ◽  
Javier Sarmiento ◽  
Jérémy Ohana ◽  
Florent Thiebaut ◽  
Sylvain Haquin ◽  
...  
Keyword(s):  
Wave Energy ◽  
Physical Modelling ◽  
Round Robin ◽  
Wave Energy Converter ◽  
Energy Converter ◽  
Mean Power ◽  
Wave Heights ◽  
Significant Wave Heights ◽  
Similar Good ◽  
Six Degree Of Freedom

The EU H2020 MaRINET2 project has a goal to improve the quality, robustness and accuracy of physical modelling and associated testing practices for the offshore renewable energy sector. To support this aim, a round robin scale physical modelling test programme was conducted to deploy a common wave energy converter at four wave basins operated by MaRINET2 partners. Test campaigns were conducted at each facility to a common specification and test matrix, providing the unique opportunity for intercomparison between facilities and working practices. A nonproprietary hinged raft, with a nominal scale of 1:25, was tested under a set of 12 irregular sea states. This allowed for an assessment of power output, hinge angles, mooring loads, and six-degree-of-freedom motions. The key outcome to be concluded from the results is that the facilities performed consistently, with the majority of variation linked to differences in sea state calibration. A variation of 5–10 % in mean power was typical and was consistent with the variability observed in the measured significant wave heights. The tank depth (which varied from 2–5 m) showed remarkably little influence on the results, although it is noted that these tests used an aerial mooring system with the geometry unaffected by the tank depth. Similar good agreement was seen in the heave, surge, pitch and hinge angle responses. In order to maintain and improve the consistency across laboratories, we make recommendations on characterising and calibrating the tank environment and stress the importance of the device–facility physical interface (the aerial mooring in this case).

Sign in / Sign up

Export Citation Format

Share Document