Comparison of Mooring Loads in Survivability Mode on the Wave Dragon Wave Energy Converter Obtained by a Numerical Model and Experimental Data

2012 ◽  
Author(s):  
Stefano Parmeggiani ◽  
Made Jaya Muliawan ◽  
Zhen Gao ◽  
Torgeir Moan ◽  
Erik Friis-Madsen
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Complex Geometry ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Coupled Analysis ◽  
Small Scale ◽  
Energy Converter ◽  
Numerical Predictions ◽  
Small Scale Model

The Wave Dragon Wave Energy Converter is ready to be up-scaled to commercial size. The design and feasibility analysis of a 1.5 MW pre-commercial unit to be deployed at the DanWEC test center in Hanstholm, Denmark, is currently ongoing. With regard to the mooring system, the design has to be carried out numerically, through coupled analyses of alternative solutions. The present study deals with the preliminary hydrodynamic characterization of Wave Dragon needed in order to calibrate the numerical model to be used for the mooring design. A hydrodynamic analysis of the small scale model in the frequency domain is performed by the software HydroD, which uses WAMIT as core software. The quadratic damping term, accounting for the viscous effect, is determined through an iterative procedure aimed at matching numerical predictions on the mooring tension, derived through time domain coupled analysis, with experimental results derived from tank tests of a small scale model. Due to the complex geometry of the device, a sensitivity analysis is performed to discuss the influence of the mean position on the quality of the numerical predictions. Good correspondence is achieved between the experimental and numerical model. The numerical model is hence considered reliable for future design applications.

scholarly journals Numerical and Experimental Investigation on a Moonpool-Buoy Wave Energy Converter

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2364 ◽  
Author(s):  
Hengxu Liu ◽  
Feng Yan ◽  
Fengmei Jing ◽  
Jingtao Ao ◽  
Zhaoliang Han ◽  
...  
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Energy Converter ◽  
Point Absorber ◽  
Motion Responses ◽  
Computational Fluid Dynamics Cfd ◽  
The Time Domain ◽  
Good Agreement

This paper introduces a new point-absorber wave energy converter (WEC) with a moonpool buoy—the moonpool platform wave energy converter (MPWEC). The MPWEC structure includes a cylinder buoy and a moonpool buoy and a Power Take-off (PTO) system, where the relative movement between the cylindrical buoy and the moonpool buoy is exploited by the PTO system to generate energy. A 1:10 scale model was physically tested to validate the numerical model and further prove the feasibility of the proposed system. The motion responses of and the power absorbed by the MPWEC studied in the wave tank experiments were also numerically analyzed, with a potential approach in the frequency domain, and a computational fluid dynamics (CFD) code in the time domain. The good agreement between the experimental and the numerical results showed that the present numerical model is accurate enough, and therefore considering only the heave degree of freedom is acceptable to estimate the motion responses and power absorption. The study shows that the MPWEC optimum power extractions is realized over a range of wave frequencies between 1.7 and 2.5 rad/s.

scholarly journals Hydro-Elastic Modelling of an Electro-Active Wave Energy Converter

2013 ◽  
Author(s):  
Aurélien Babarit ◽  
Benjamin Gendron ◽  
Jitendra Singh ◽  
Cécile Mélis ◽  
Philippe Jean
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Ocean Basin ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Linear Potential ◽  
Energy Converter ◽  
Outer Flow ◽  
Modal Expansion ◽  
Linear Potential Theory

Since 2009, SBM Offshore has been developing the S3 Wave Energy Converter (S3 WEC). It consists in a long flexible tube made of an Electro-Active Polymer (EAP). Thus, the structural material is also the Power Take Off (PTO). In order to optimize the S3 WEC, a hydro-elastic numerical model able to predict the device dynamic response has been developed. The inner flow, elastic wall deformations and outer flow are taken into account in the model under the following assumptions: Euler equation is used for the inner flow. The flow is also assumed to be uniform. Elastic deformation of the wall tube is linearized. The outer flow is modeled using linear potential theory. These equations have been combined in order to build the numerical model. First, they are solved in the absence of the outer fluid in order to obtain the modes of response of the device. Secondly, the outer fluid is taken into account and the equation of motion is solved by making use of modal expansion. Meanwhile, experimental validation tests were conducted in the ocean basin at Ecole Centrale De Nantes. The scale model is 10m long tube made of EAP. The tube deformations were measured using the electro-active polymer. The model was also equipped with sensors in order to measure the inner pressure. Comparisons of the deformation rate between the numerical model and experimental results show good agreement, provided that the wall damping is calibrated. Eventually, results of a technico-economical parametric study of the dimensions of the device are presented.

scholarly journals Wave Tank Testing of a Pendulum Wave Energy Converter 1:12 Scale Model

2017 ◽  
Vol 09 (02) ◽  
pp. 1750024 ◽  
Author(s):  
Pozzi Nicola ◽  
Bracco Giovanni ◽  
Passione Biagio ◽  
Sirigu Sergej Antonello ◽  
Vissio Giacomo ◽  
...  
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Ocean Waves ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Energy Converter ◽  
Research Activities ◽  
Present Decade ◽  
Pendulum Wave Energy Converter ◽  
Pendulum Wave

Wave Energy is a widespread, reliable renewable energy source. The early study on Wave Energy dates back in the 70’s, with a particular effort in the last and present decade to make Wave Energy Converters (WECs) more profitable and predictable. The PeWEC (Pendulum Wave Energy Converter) is a pendulum-based WEC. The research activities described in the present work aim to develop a pendulum converter for the Mediterranean Sea, where waves are shorter, thus with a higher frequency compared to the ocean waves, a characteristic well agreeing with the PeWEC frequency response. The mechanical equations of the device are developed and coupled with the hydrodynamic Cummins equation. The work deals with the design and experimental tank test of a 1:12 scale prototype. The experimental data recorded during the testing campaign are used to validate the numerical model previously described. The numerical model proved to be in good agreement with the experiments.

scholarly journals A broadbanded pressure differential wave energy converter based on dielectric elastomer generators

2021 ◽  
Author(s):  
Michele Righi ◽  
Giacomo Moretti ◽  
David Forehand ◽  
Lorenzo Agostini ◽  
Rocco Vertechy ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Deformations ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Pressure Differential ◽  
Design Stage ◽  
Small Scale ◽  
Energy Converter ◽  
Wide Range ◽  
The Waves

AbstractDielectric elastomer generators (DEGs) are a promising option for the implementation of affordable and reliable sea wave energy converters (WECs), as they show considerable promise in replacing expensive and inefficient power take-off systems with cheap direct-drive generators. This paper introduces a concept of a pressure differential wave energy converter, equipped with a DEG power take-off operating in direct contact with sea water. The device consists of a closed submerged air chamber, with a fluid-directing duct and a deformable DEG power take-off mounted on its top surface. The DEG is cyclically deformed by wave-induced pressure, thus acting both as the power take-off and as a deformable interface with the waves. This layout allows the partial balancing of the stiffness due to the DEG’s elasticity with the negative hydrostatic stiffness contribution associated with the displacement of the water column on top of the DEG. This feature makes it possible to design devices in which the DEG exhibits large deformations over a wide range of excitation frequencies, potentially achieving large power capture in a wide range of sea states. We propose a modelling approach for the system that relies on potential-flow theory and electroelasticity theory. This model makes it possible to predict the system dynamic response in different operational conditions and it is computationally efficient to perform iterative and repeated simulations, which are required at the design stage of a new WEC. We performed tests on a small-scale prototype in a wave tank with the aim of investigating the fluid–structure interaction between the DEG membrane and the waves in dynamical conditions and validating the numerical model. The experimental results proved that the device exhibits large deformations of the DEG power take-off over a broad range of monochromatic and panchromatic sea states. The proposed model demonstrates good agreement with the experimental data, hence proving its suitability and effectiveness as a design and prediction tool.

Wave Energy Hyperbaric Device for Electricity Production

2007 ◽  
Author(s):  
Segen F. Estefen ◽  
Paulo Roberto da Costa ◽  
Eliab Ricarte ◽  
Marcelo M. Pinheiro
Keyword(s):  
Power Generation ◽  
Wave Energy ◽  
Experimental Results ◽  
Electricity Production ◽  
Scale Model ◽  
Small Scale ◽  
Regular Waves ◽  
Hyperbaric Chamber ◽  
Small Scale Model

Wave energy is a renewable and non-polluting source and its use is being studied in different countries. The paper presents an overview on the harnessing of energy from waves and the activities associated with setting up a plant for extracting energy from waves in Port of Pecem, on the coast of Ceara State, Brazil. The technology employed is based on storing water under pressure in a hyperbaric chamber, from which a controlled jet of water drives a standard turbine. The wave resource at the proposed location is presented in terms of statistics data obtained from previous monitoring. The device components are described and small scale model tested under regular waves representatives of the installation region. Based on the experimental results values of prescribed pressures are identified in order to optimize the power generation.

scholarly journals Experimental Analysis of a Novel Adaptively Counter-Rotating Wave Energy Converter for Powering Drifters

2019 ◽  
Vol 7 (6) ◽  
pp. 171 ◽  
Author(s):  
Guoheng Wu ◽  
Zhongyue Lu ◽  
Zirong Luo ◽  
Jianzhong Shang ◽  
Chongfei Sun ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Irregular Waves ◽  
Surface Velocity ◽  
Small Scale ◽  
Power Constraint ◽  
Energy Converter ◽  
Wave Tank ◽  
Wide Range ◽  
Rotating Wave

Nowadays, drifters are used for a wide range of applications for researching and exploring the sea. However, the power constraint makes it difficult for their sampling intervals to be smaller, meaning that drifters cannot transmit more accurate measurement data to satellites. Furthermore, due to the power constraint, a modern Surface Velocity Program (SVP) drifter lives an average of 400 days before ceasing transmission. To overcome the power constraint of SVP drifters, this article proposes an adaptively counter-rotating wave energy converter (ACWEC) to supply power for drifters. The ACWEC has the advantages of convenient modular integration, simple conversion process, and minimal affection by the crucial sea environment. This article details the design concept and working principle, and the interaction between the wave energy converter (WEC) and wave is presented based on plane wave theory. To verify the feasibility of the WEC, the research team carried out a series of experiments in a wave tank with regular and irregular waves. Through experiments, it was found that the power and efficiency of the ACWEC are greatly influenced by parameters such as wave height and wave frequency. The maximum output power of the small scale WEC in a wave tank is 6.36 W, which allows drifters to detect ocean data more frequently and continuously.

A Joint Numerical and Experimental Study of a Surging Point Absorbing Wave Energy Converter (WRASPA)

2009 ◽  
Author(s):  
Majid A. Bhinder ◽  
Clive G. Mingham ◽  
Derek M. Causon ◽  
Mohammad T. Rahmati ◽  
George A. Aggidis ◽  
...  
Keyword(s):  
Wave Energy ◽  
Informed Choice ◽  
Wave Energy Converter ◽  
Body Motion ◽  
Numerical Dissipation ◽  
Small Scale ◽  
Linear Wave ◽  
Energy Converter ◽  
Non Linear ◽  
Experimental Project

This paper presents the findings from using several commercial computational fluid dynamics codes in a joint numerical and experimental project to simulate WRASPA, a new wave energy converter (WEC) device. A series of fully 3D non-linear simulations of WRASPA are presented. Three commercial codes STAR-CCM, CFX and FLOW-3D are considered for simulating the WRASPA device and final results are presented based on the use of Flow-3D. Results are validated by comparison to experimental data obtained from small scale tank tests undertaken at Lancaster University (LU). The primary aim of the project is to use numerical simulation to optimize the collector geometry for power production over a range of likely wave climates. A secondary aim is to evaluate the ability of commercial codes to simulate rigid body motion in linear and non-linear wave climates in order to choose the optimal code with respect to compute speed and ease of problem setup. Issues relating to the ability of a code in terms of numerical dissipation of waves, wave absorption, wave breaking, grid generation and moving bodies will all be discussed. The findings of this paper serve as a basis for an informed choice of commercial package for such simulations. However the capability of these commercial codes is increasing with every new release.

Design and Potential Application of Small Scale Wave Energy Converter

2017 ◽  
Author(s):  
Tunde O. Aderinto ◽  
Francisco Haces-Fernandez ◽  
Hua Li
Keyword(s):  
Wave Energy ◽  
Energy Production ◽  
Energy Resource ◽  
Appropriate Technology ◽  
Wave Energy Converter ◽  
Small Scale ◽  
Ocean Energy ◽  
Energy Converter ◽  
Wave Energy Converters ◽  
Wave Properties

Although theoretical available wave energy is higher than most of ocean energy sources, the commercial utilization of wave energy is much slower than other ocean energy sources. The difficulty of integration with the electrical grid system and the challenges of the installation, operation and maintenance of large energy generation and transmission systems are the major reasons. Even though there are successfully tested models of wave energy converters, the fact that wave energy is directly affected by wave height and wave period makes the actual wave energy output with high variation and difficult to be predicted. And most of the previous studies on wave energy and its utilization have focused on the large scale energy production that can be integrated into a power grid system. In this paper, the authors identify and discuss stand-alone wave energy converter systems and facilities that are not connected to the electricity grid with focus on small scale wave energy systems as potential source of energy. For the proper identification, qualification and quantification of wave energy resource potential, wave properties such as wave height and period need to be characterized. This is used to properly determine and predict the probability of the occurrence of these wave properties at particular locations, which enables the choice of product design, installation, operation and maintenance to effectively capture wave energy. Meanwhile, the present technologies available for wave energy converters can be limited by location (offshore, nearshore or shoreline). Therefore, the potential applications of small scale stand-alone wave energy converter are influenced by the demand, location of the need and the appropriate technology to meet the identified needs. The paper discusses the identification of wave energy resource potentials, the location and appropriate technology suitable for small scale wave energy converter. Two simplified wave energy converter designs are created and simulated under real wave condition in order to estimate the energy production of each design.

Sign in / Sign up

Export Citation Format

Share Document