scholarly journals Nitrogen-Doped Carbon Nanotube/Polypropylene Composites with Negative Seebeck Coefficient

2020 ◽  
Vol 4 (1) ◽  
pp. 14 ◽  
Author(s):  
Beate Krause ◽  
Ioannis Konidakis ◽  
Mohammad Arjmand ◽  
Uttandaraman Sundararaj ◽  
Robert Fuge ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Transient Absorption ◽  
Transient Absorption Spectroscopy ◽  
Polypropylene Composites ◽  
Nitrogen Doped ◽  
Seebeck Coefficients ◽  
Multi Walled Carbon Nanotubes ◽  
Nitrogen Doped Carbon

This study describes the application of multi-walled carbon nanotubes that were nitrogen-doped during their synthesis (N-MWCNTs) in melt-mixed polypropylene (PP) composites. Different types of N-MWCNTs, synthesized using different methods, were used and compared. Four of the five MWCNT grades showed negative Seebeck coefficients (S), indicating n-type charge carrier behavior. All prepared composites (with a concentration between 2 and 7.5 wt% N-MWCNTs) also showed negative S values, which in most cases had a higher negative value than the corresponding nanotubes. The S values achieved were between 1.0 μV/K and −13.8 μV/K for the N-MWCNT buckypapers or powders and between −4.7 μV/K and −22.8 μV/K for the corresponding composites. With a higher content of N-MWCNTs, the increase in electrical conductivity led to increasing values of the power factor (PF) despite the unstable behavior of the Seebeck coefficient. The highest power factor was achieved with 4 wt% N-MWCNT, where a suitable combination of high electrical conductivity and acceptable Seebeck coefficient led to a PF value of 6.1 × 10−3 µW/(m·K2). First experiments have shown that transient absorption spectroscopy (TAS) is a useful tool to study the carrier transfer process in CNTs in composites and to correlate it with the Seebeck coefficient.

scholarly journals The Investigation of the Seebeck Effect of the Poly(3,4-Ethylenedioxythiophene)-Tosylate with the Various Concentrations of an Oxidant

Polymers ◽  
2018 ◽  
Vol 11 (1) ◽  
pp. 21 ◽  
Author(s):  
Joon-Soo Kim ◽  
Woongsik Jang ◽  
Dong Wang
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
In Situ Polymerization ◽  
Seebeck Effect ◽  
Particle Sizes ◽  
Seebeck Coefficients ◽  
Optimal Power ◽  
Electrical Conductivities

Poly(3,4-ethylenedioxythiophene)-tosylate (PEDOT-Tos) can be synthesized through an in situ polymerization and doping process with iron(III) p-toluenesulfonate hexahydrate as an oxidant. Both the Seebeck coefficient and the electrical conductivity were modified by varying the concentration of the oxidant. We investigated the effects of varying the concentration of the oxidant on the particle sizes and doping (oxidation) levels of PEDOT-Tos for thermoelectric applications. We demonstrated that an increase in the oxidant enabled an expansion of the particle sizes and the doping levels of the PEDOT-Tos. The modification of the doping levels by the concentration of the oxidant can provide another approach for having an optimal power factor for thermoelectric applications. De-doping of PEDOTs by reduction agents has been generally investigated for changing its oxidation levels. In this study, we investigated the effect of the concentration of the oxidant of PEDOT-Tos on the oxidation levels, the electrical conductivities and the Seebeck coefficients. As loading the oxidant of PEDOT-Tos, the Seebeck coefficient was compromised, while the electrical conductivity increased.

scholarly journals Nanocomposites with p- and n-Type Conductivity Controlled by Type and Content of Nanotubes in Thermosets for Thermoelectric Applications

Nanomaterials ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 1144
Author(s):  
Katharina Kröning ◽  
Beate Krause ◽  
Petra Pötschke ◽  
Bodo Fiedler
Keyword(s):  
Carbon Nanotubes ◽  
Seebeck Coefficient ◽  
Single Walled Carbon Nanotubes ◽  
Mwcnt Content ◽  
Nitrogen Doped ◽  
Seebeck Coefficients ◽  
Different Types ◽  
Multi Walled Carbon Nanotubes ◽  
P Type ◽  
Walled Carbon Nanotubes

In this work, composites based on epoxy resin and various carbon nanotubes (CNTs) were studied regarding their thermoelectric properties. The epoxy composites were prepared by infiltration of preformed CNT buckypapers. The influence of different types of CNTs on the Seebeck coefficient was investigated, namely lab-made and commercially available multi walled carbon nanotubes (MWCNTs), lab-made nitrogen doped MWCNTs (N-MWCNT) and commercially available single walled carbon nanotubes (SWCNTs). It was found that only by varying the lab-made MWCNT content could both n- and p-type composites be produced with Seebeck coefficients between −9.5 and 3.1 µV/K. The incorporation of N-MWCNTs resulted in negative Seebeck coefficients of −11.4 to −17.4 µV/K. Thus, the Seebeck coefficient of pure SWCNT changed from 37.4 to −25.5 µV/K in the epoxy/1 wt. % SWCNT composite. A possible explanation for the shift in the Seebeck coefficient is the change of the CNTs Fermi level depending on the number of epoxy molecules on the CNT surface.

scholarly journals Formation and Evaluation of Silicon Substrate with Highly-Doped Porous Si Layers Formed by Metal-Assisted Chemical Etching

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Yijie Li ◽  
Nguyen Van Toan ◽  
Zhuqing Wang ◽  
Khairul Fadzli Bin Samat ◽  
Takahito Ono
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Contact Resistance ◽  
Power Factor ◽  
Chemical Etching ◽  
Porous Si ◽  
Si Substrate ◽  
Si Substrates ◽  
Output Performance ◽  
Metal Assisted Chemical Etching

AbstractPorous silicon (Si) is a low thermal conductivity material, which has high potential for thermoelectric devices. However, low output performance of porous Si hinders the development of thermoelectric performance due to low electrical conductivity. The large contact resistance from nonlinear contact between porous Si and metal is one reason for the reduction of electrical conductivity. In this paper, p- and n-type porous Si were formed on Si substrate by metal-assisted chemical etching. To decrease contact resistance, p- and n-type spin on dopants are employed to dope an impurity element into p- and n-type porous Si surface, respectively. Compared to the Si substrate with undoped porous samples, ohmic contact can be obtained, and the electrical conductivity of doped p- and n-type porous Si can be improved to 1160 and 1390 S/m, respectively. Compared with the Si substrate, the special contact resistances for the doped p- and n-type porous Si layer decreases to 1.35 and 1.16 mΩ/cm2, respectively, by increasing the carrier concentration. However, the increase of the carrier concentration induces the decline of the Seebeck coefficient for p- and n-type Si substrates with doped porous Si samples to 491 and 480 μV/K, respectively. Power factor is related to the Seebeck coefficient and electrical conductivity of thermoelectric material, which is one vital factor that evaluates its output performance. Therefore, even though the Seebeck coefficient values of Si substrates with doped porous Si samples decrease, the doped porous Si layer can improve the power factor compared to undoped samples due to the enhancement of electrical conductivity, which facilitates its development for thermoelectric application.

scholarly journals Preparation and Thermoelectric Properties of Graphite/poly(3,4-ethyenedioxythiophene) Nanocomposites

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2849 ◽  
Author(s):  
Yong Du ◽  
Haixia Li ◽  
Xuechen Jia ◽  
Yunchen Dou ◽  
Jiayue Xu ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Oxidative Polymerization ◽  
Polymerization Process ◽  
Measurement Temperature ◽  
Temperature Range ◽  
Different Content

Graphite/poly(3,4-ethyenedioxythiophene) (PEDOT) nanocomposites were prepared by an in-situ oxidative polymerization process. The electrical conductivity and Seebeck coefficient of the graphite/PEDOT nanocomposites with different content of graphite were measured in the temperature range from 300 K to 380 K. The results show that as the content of graphite increased from 0 to 37.2 wt %, the electrical conductivity of the nanocomposites increased sharply from 3.6 S/cm to 80.1 S/cm, while the Seebeck coefficient kept almost the same value (in the range between 12.0 μV/K to 15.1 μV/K) at 300 K, which lead to an increased power factor. The Seebeck coefficient of the nanocomposites increased from 300 K to 380 K, while the electrical conductivity did not substantially depend on the measurement temperature. As a result, a power factor of 3.2 μWm−1 K−2 at 380 K was obtained for the nanocomposites with 37.2 wt % graphite.

Nitrogen doped carbon nanotubes and nanofibers: Composition, structure, electrical conductivity and capacity properties

Carbon ◽  
2017 ◽  
Vol 122 ◽  
pp. 475-483 ◽  
Author(s):  
Olga Yu. Podyacheva ◽  
Svetlana V. Cherepanova ◽  
Anatoly I. Romanenko ◽  
Lidiya S. Kibis ◽  
Dmitry A. Svintsitskiy ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Nitrogen Doped ◽  
Composition Structure ◽  
Nitrogen Doped Carbon

scholarly journals Annealing Effect on the Thermoelectric Properties of Bi2Te3Thin Films Prepared by Thermal Evaporation Method

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Jyun-Min Lin ◽  
Ying-Chung Chen ◽  
Chi-Pi Lin
Keyword(s):  
Thin Films ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Thermal Evaporation ◽  
Thermal Evaporation Method ◽  
Si Substrates ◽  
Seebeck Coefficients

Bismuth telluride-based compounds are known to be the best thermoelectric materials within room temperature region, which exhibit potential applications in cooler or power generation. In this paper, thermal evaporation processes were adopted to fabricate the n-type Bi2Te3thin films on SiO2/Si substrates. The influence of thermal annealing on the microstructures and thermoelectric properties of Bi2Te3thin films was investigated in temperature range 100–250°C. The crystalline structures and morphologies were characterized by X-ray diffraction and field emission scanning electron microscope analyses. The Seebeck coefficients, electrical conductivity, and power factor were measured at room temperature. The experimental results showed that both the Seebeck coefficient and power factor were enhanced as the annealing temperature increased. When the annealing temperature increased to 250°C for 30 min, the Seebeck coefficient and power factor of n-type Bi2Te3-based thin films were found to be about −132.02 μV/K and 6.05 μW/cm·K2, respectively.

scholarly journals Influence of crystallinity on the thermoelectric power factor of P3HT vapour-doped with F4TCNQ

RSC Advances ◽  
2018 ◽  
Vol 8 (3) ◽  
pp. 1593-1599 ◽  
Author(s):  
Jonna Hynynen ◽  
David Kiefer ◽  
Christian Müller
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Power ◽  
Power Factor ◽  
Thermoelectric Power Factor ◽  
Order Of Magnitude

The crystallinity of P3HT strongly benefits the electrical conductivity but not Seebeck coefficient, leading to an increase in power factor by one order of magnitude.

Carbon nanotubes enhanced Seebeck coefficient and power factor of rutile TiO2

2015 ◽  
Vol 17 (12) ◽  
pp. 8120-8124 ◽  
Author(s):  
Yao-Cheng Lai ◽  
Hsin-Jung Tsai ◽  
Chia-I Hung ◽  
Hiroyuki Fujishiro ◽  
Tomoyuki Naito ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Filling Fraction ◽  
Rutile Tio2

Ti–C substitution occurs when carbon nanotubes were thermally dispersed in rutile TiO2 and the electrical conductivity as well as Seebeck coefficient were simultaneously promoted at a low filling fraction of tubes.

Synthesis and Characterization of Nitrogen Doped Carbon Nanotubes

2010 ◽  
Vol 636-637 ◽  
pp. 714-721 ◽  
Author(s):  
K. Kordatos ◽  
A. Ntziouni ◽  
A. Theodoratou ◽  
Maria Perraki ◽  
M. Terrones ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Production Method ◽  
X Ray Diffraction ◽  
Nitrogen Doped ◽  
Solid Mixture ◽  
Multi Walled Carbon Nanotubes ◽  
Metallic Catalyst ◽  
Nitrogen Doped Carbon ◽  
Walled Carbon Nanotubes

The present work describes the synthesis of nitrogen doped multi-walled carbon nanotubes (CNx CNT). The chosen production method was the catalytic pyrolysis of a solid mixture containing [Ni(DMG)2] and melamine (C3H6N6), under an Αr atmosphere. A series of various experiments were performed, using different proportions of the reaction mixture, in order to optimize the production conditions of nitrogen doped carbon nanotubes. Finally, the produced materials were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX), Raman spectroscopy as well as thermogravimetric analysis (TGA). The obtained data from all the above analyses, showed the formation of nitrogen doped carbon nanotubes of various diameters as well as nanofibers surrounded by byproducts such as aggregations of amorphous carbon and metallic catalyst, depending on the proportion of the reaction mixture.

TEXTURED STRUCTURE AND ANISOTROPIC THERMOELECTRIC PROPERTIES OF Ca2.7Bi0.3Co4O9 OXIDE PREPARED BY CONVENTIONAL SOLID-STATE REACTION

2009 ◽  
Vol 23 (01) ◽  
pp. 87-95 ◽  
Author(s):  
HAOSHAN HAO ◽  
QINGLIN HE ◽  
CHANGQING CHEN ◽  
HONGWEI SUN ◽  
XING HU
Keyword(s):  
Electrical Conductivity ◽  
Grain Size ◽  
Solid State ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
Bi Doping

Ca 3-x Bi x Co 4 O 9(x = 0.0, 0.3) samples have been prepared at 1223 K by conventional solid-state reaction method. XRD and SEM investigations reveal that c-axis-oriented structure could be formed in Ca 2.7 Bi 0.3 Co 4 O 9 samples, whereas grains in Ca 3 Co 4 O 9 samples distribute randomly. Moreover, Bi doping increases the grain size and relative density of Ca 2.7 Bi 0.3 Co 4 O 9. The electrical conductivity along the ab plane for Ca 2.7 Bi 0.3 Co 4 O 9 is about four times as large as that along the c-axis, but the Seebeck coefficient is almost isotropic, which leads to a remarkable rise of the power factor in ab plane for Ca 2.7 Bi 0.3 Co 4 O 9 compared with untextured Ca 3 Co 4 O 9. The textured structure in Ca 2.7 Bi 0.3 Co 4 O 9 sample should be attributed to the effect of Bi doping.

Sign in / Sign up

Export Citation Format

Share Document