scholarly journals Ion Transport Study in CS: POZ Based Polymer Membrane Electrolytes Using Trukhan Model

2019 ◽  
Vol 20 (21) ◽  
pp. 5265 ◽  
Author(s):  
Aziz ◽  
Karim ◽  
Brza ◽  
Abdulwahid ◽  
Saeed ◽  
...  
Keyword(s):  
Ion Transport ◽  
Polymer Blend ◽  
Imaginary Part ◽  
Electric Modulus ◽  
Transport Parameters ◽  
Impedance Plot ◽  
Relaxation Dynamic ◽  
Different Temperatures ◽  
Solution Cast ◽  
Xrd Patterns

In this work, analysis of ion transport parameters of polymer blend electrolytes incorporated with magnesium trifluoromethanesulfonate (Mg(CF3SO3)2) was carried out by employing the Trukhan model. A solution cast technique was used to obtain the polymer blend electrolytes composed of chitosan (CS) and poly (2-ethyl-2-oxazoline) (POZ). From X-ray diffraction (XRD) patterns, improvement in amorphous phase for the blend samples has been observed in comparison to the pure state of CS. From impedance plot, bulk resistance (Rb) was found to decrease with increasing temperature. Based on direct current (DC) conductivity (σdc) patterns, considerations on the ion transport models of Arrhenius and Vogel–Tammann–Fulcher (VTF) were given. Analysis of the dielectric properties was carried out at different temperatures and the obtained results were linked to the ion transport mechanism. It is demonstrated in the real part of electrical modulus that chitosan-salt systems are extremely capacitive. The asymmetric peak of the imaginary part (Mi) of electric modulus indicated that there is non-Debye type of relaxation for ions. From frequency dependence of dielectric loss (ε″) and the imaginary part (Mi) of electric modulus, suitable coupling among polymer segmental and ionic motions was identified. Two techniques were used to analyze the viscoelastic relaxation dynamic of ions. The Trukhan model was used to determine the diffusion coefficient (D) by using the frequency related to peak frequencies and loss tangent maximum heights (tanδmax). The Einstein–Nernst equation was applied to determine the carrier number density (n) and mobility. The ion transport parameters, such as D, n and mobility (μ), at room temperature, were found to be 4 × 10−5 cm2/s, 3.4 × 1015 cm−3, and 1.2 × 10−4 cm2/Vs, respectively. Finally, it was shown that an increase in temperature can also cause these parameters to increase.

Frequency and temperature-dependent impedance spectroscopy of PVA/PEG polymer blend film

2018 ◽  
Vol 30 (8) ◽  
pp. 918-926 ◽  
Author(s):  
Rakhi Nangia ◽  
Neeraj K Shukla ◽  
Ambika Sharma
Keyword(s):  
Polymer Blend ◽  
Electric Modulus ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Casting Technique ◽  
Blend Films ◽  
Structural Details ◽  
Different Temperatures ◽  
Solution Casting Technique ◽  
Poly Ethylene

In this work, polymer blend films based on polyvinyl alcohol (PVA)/poly(ethylene glycol) (PEG) were prepared by solution casting technique. X-ray diffraction (XRD) analysis was performed to investigate the structural details of the polymer blend. XRD pattern confirms the polycrystalline nature of the films. Sandwich structures of the type Ag-PVA/PEG-Ag were formed to study the dielectric and conduction properties in the frequency range 300 Hz–3 MHz and at different temperatures varying from 298 K to 420 K. Experimental results show that both dielectric constant ( ε′) and dielectric loss ( ε″) values were strong functions of frequency and temperature. The AC conductivity ( σAC) was found to obey the power law Aωs and correlated barrier hopping as the conduction mechanism. The imaginary part of electric modulus shows peak shifting corresponding to relaxation mechanisms. Electric modulus study was also found to support the dielectric permittivity data.

scholarly journals A Polymer Blend Electrolyte Based on CS with Enhanced Ion Transport and Electrochemical Properties for Electrical Double Layer Capacitor Applications

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 930
Author(s):  
Shujahadeen B. Aziz ◽  
Elham M. A. Dannoun ◽  
Muhamad H. Hamsan ◽  
Hewa O. O. Ghareeb ◽  
Muaffaq M. Nofal ◽  
...  
Keyword(s):  
Ion Transport ◽  
Transport Properties ◽  
Polymer Electrolyte ◽  
Internal Resistance ◽  
Transport Parameter ◽  
Transport Parameters ◽  
Double Layer Capacitor ◽  
Solution Cast ◽  
Polymer Blend Electrolyte ◽  
Good Agreement

The fabrication of energy storage EDLC in this work is achieved with the implementation of a conducting chitosan–methylcellulose–NH4NO3–glycerol polymer electrolyte system. The simple solution cast method has been used to prepare the electrolyte. The impedance of the samples was fitted with equivalent circuits to design the circuit diagram. The parameters associated with ion transport are well studied at various plasticizer concentrations. The FTIR investigation has been done on the films to detect the interaction that occurs among plasticizer and polymer electrolyte. To get more insights into ion transport parameters, the FTIR was deconvoluted. The transport properties achieved from both impedance and FTIR are discussed in detail. It was discovered that the transport parameter findings are in good agreement with both impedance and FTIR studies. A sample with high transport properties was characterized for ion dominancy and stability through the TNM and LSV investigations. The dominancy of ions in the electrolyte verified as the tion of the electrolyte is established to be 0.933 whereas it is potentially stable up to 1.87 V. The rechargeability of the EDLC is steady up to 500 cycles. The internal resistance, energy density, and power density of the EDLC at the 1st cycle are 53 ohms, 6.97 Wh/kg, and 1941 W/kg, respectively.

scholarly journals Structural, Electrical and Electrochemical Properties of Glycerolized Biopolymers Based on Chitosan (CS): Methylcellulose (MC) for Energy Storage Application

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1183
Author(s):  
Shujahadeen B. Aziz ◽  
Ahmad S. F. M. Asnawi ◽  
Mohd Fakhrul Zamani Kadir ◽  
Saad M. Alshehri ◽  
Tansir Ahamad ◽  
...  
Keyword(s):  
Energy Storage ◽  
Ion Transport ◽  
Ammonium Thiocyanate ◽  
Transference Number ◽  
Ionic Mobility ◽  
Transport Parameters ◽  
Ionic Transference Number ◽  
Energy Storage Application ◽  
Electrochemical Double Layer ◽  
Ion Conducting

In this work, a pair of biopolymer materials has been used to prepare high ion-conducting electrolytes for energy storage application (ESA). The chitosan:methylcellulose (CS:MC) blend was selected as a host for the ammonium thiocyanate NH4SCN dopant salt. Three different concentrations of glycerol was successfully incorporated as a plasticizer into the CS–MC–NH4SCN electrolyte system. The structural, electrical, and ion transport properties were investigated. The highest conductivity of 2.29 × 10−4 S cm−1 is recorded for the electrolyte incorporated 42 wt.% of plasticizer. The complexation and interaction of polymer electrolyte components are studied using the FTIR spectra. The deconvolution (DVN) of FTIR peaks as a sensitive method was used to calculate ion transport parameters. The percentage of free ions is found to influence the transport parameters of number density (n), ionic mobility (µ), and diffusion coefficient (D). All electrolytes in this work obey the non-Debye behavior. The highest conductivity electrolyte exhibits the dominancy of ions, where the ionic transference number, tion value of (0.976) is near to infinity with a voltage of breakdown of 2.11 V. The fabricated electrochemical double-layer capacitor (EDLC) achieves the highest specific capacitance, Cs of 98.08 F/g at 10 mV/s by using the cyclic voltammetry (CV) technique.

Polyvinyl fibers as outperform candidature in the solid polymer electrolytes

2020 ◽  
pp. 152808372097062
Author(s):  
Muhammad Yameen Solangi ◽  
Umair Aftab ◽  
Muhammad Ishaque ◽  
Aqeel Bhutto ◽  
Ayman Nafady ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Weight Loss ◽  
Ionic Conductivity ◽  
Polymer Electrolytes ◽  
Vital Role ◽  
Solid Polymer Electrolytes ◽  
Solid Polymer ◽  
Main Challenge ◽  
Different Temperatures ◽  
Solution Cast

Solid polymer electrolytes (SPEs) are the best choice to replace liquid electrolytes in supercapacitors, fuel cells, solar cells and batteries. The main challenge in this filed is the ionic conductivity and thermal stability of SPEs which is still not up to mark, therefore more investigations are needed to address these issues. In this study, PVA/salt based SPEs was fabricated using both solution cast and electro-spinning methods to probe the effect of different salts such as (NaCl, KCl and KI) and their concentrations on the ionic conductivity. Scanning electron microscopy (SEM) x and Fourier Transform Infra-Red (FTIR) have been employed to study the morphology as well as the different functional groups of SPEs, respectively. It was noted that small addition of NaCl, KCl and KI salts in SPEs dramatically increased the ionic conductivity to 5.95×10−6, 5.31×10−6 and 4.83×10−6 S/cm, respectively. Importantly, the SPEs obtained with NaCl via electro-spinning have higher ionic conductivity (5.95×10−6 S/cm) than their casted SPEs (1.87×10−6 S/cm). Thermal stability was also studied at two different temperatures i.e. 80 °C and 100 °C. The weight loss percentage of electrospun SPEs have zero percent weight loss than the solution based SPEs. The combined results clearly indicated that the nature of salt, concentration and fabrication process play a vital role in the ionic conductivity. Also, the NaCl salt with low molecular weight at low concentrations shows an enhanced ionic conductivity.

scholarly journals Electrical Conduction Mechanism in Solid Polymer Electrolytes: New Concepts to Arrhenius Equation

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Shujahadeen B. Aziz ◽  
Zul Hazrin Z. Abidin
Keyword(s):  
Dielectric Constant ◽  
Polymer Electrolytes ◽  
Conduction Mechanism ◽  
Dc Conductivity ◽  
Solid Polymer Electrolytes ◽  
Solid Polymer ◽  
Arrhenius Behavior ◽  
Different Temperatures ◽  
Solution Cast ◽  
The Fourier Transform

Solid polymer electrolytes based on chitosan NaCF3SO3 have been prepared by the solution cast technique. X-ray diffraction shows that the crystalline phase of the pure chitosan membrane has been partially disrupted. The fourier transform infrared (FTIR) results reveal the complexation between the chitosan polymer and the sodium triflate (NaTf) salt. The dielectric constant and DC conductivity follow the same trend with NaTf salt concentration. The increase in dielectric constant at different temperatures indicates an increase in DC conductivity. The ion conduction mechanism follows the Arrhenius behavior. The dependence of DC conductivity on both temperature and dielectric constant (σdc(T,ε′)=σ0e−Ea/KBT) is also demonstrated.

Preparation and Characterization of NTC NiMn2O4-La1-xCaxMnO3 (0≤x≤0.3) Composite Ceramics

2013 ◽  
Vol 716 ◽  
pp. 78-83 ◽  
Author(s):  
Hui Min Zhang ◽  
Fang Guan ◽  
Ai Min Chang ◽  
Li Jun Zhao
Keyword(s):  
Electrical Resistivity ◽  
Perovskite Structure ◽  
Spinel Structure ◽  
Thermal Constant ◽  
Inrush Current ◽  
Composite Ceramics ◽  
Sem Images ◽  
Conventional Solid State Reaction ◽  
Different Temperatures ◽  
Xrd Patterns

Composite ceramics made of spinel structure NiMn2O4 and CaO-doped perovskite structure LaMnO3 were prepared by a conventional solid state reaction and sintered at different temperatures. The XRD patterns have shown that the major phases presented in the sintered samples are NiMn2O4 compounds with the spinel structure, La1-xCaxMnO3 with the perovskite structure and NiO with a monoclinic structure. SEM images show that the density and grain size of the composite ceramics increases with sintered temperature increasing. The electrical resistivity of the composite ceramics at 25°C is found to change significantly depending on the CaO content, while the thermal constant B is still reasonably large in the range of 2400 to 3000 K. For the composition x = 0.1, the composite with a low electrical resistivity (ρ25°C=4.46Ω·cm) and moderate B value (B25/50=2762K) was obtained. These composites could be applied as potential candidates for NTC thermistors in the suppression of the inrush current.

Effect of Annealing Atmosphere on the Morphology of Copper Oxide Thin Films Deposited on TiO2 Substrates Prepared by Sol-Gel Process

2013 ◽  
Vol 594-595 ◽  
pp. 113-117 ◽  
Author(s):  
Dewi Suriyani Che Halin ◽  
Ibrahim Abu Talib ◽  
Abdul Razak Daud ◽  
Muhammad Azmi Abdul Hamid
Keyword(s):  
Thin Films ◽  
Surface Roughness ◽  
Grain Size ◽  
Copper Oxide ◽  
Spin Coating ◽  
Sol Gel ◽  
Annealing Atmosphere ◽  
Oxide Thin Films ◽  
Different Temperatures ◽  
Xrd Patterns

Copper oxide films were prepared via sol-gel like spin coating starting from methanolic solutions of cupric chloride onto the TiO2 substrates. Films were obtained by spin coating under room conditions (temperature, 25-30 °C) and were subsequently annealed at different temperatures (200-400 °C) in oxidizing (air) and inert (N2) atmospheres. X-ray diffraction (XRD) patterns showed crystalline phases, which were observed as a function of the annealing conditions. The film composition resulted single or multi-phasic depending on both temperature and atmosphere. The grain size of film was measured using scanning electron microscopy (SEM) and the surface roughness of thin films was characterized by atomic force microscopy (AFM). The grain size of which was annealed in air at 300 °C was 30.39 nm with the surface roughness of 96.16 nm. The effects of annealing atmosphere on the structure and morphology of copper oxide thin films are reported.

Effect of Annealing on Microstructure of Hydroxyapatite Coatings and their Behaviours in Simulated Body Fluid

2014 ◽  
Vol 922 ◽  
pp. 657-662 ◽  
Author(s):  
Sharidah Azuar Abdul Azis ◽  
John Kennedy ◽  
Peng Cao
Keyword(s):  
Heat Treatment ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Ion Beam ◽  
Apatite Formation ◽  
Ion Beam Sputtering ◽  
Different Temperatures ◽  
Higher Temperature ◽  
Xrd Patterns ◽  
Post Deposition

In this study, hydroxyapatite (HA) coatings on Ti6Al4V substrate were deposited using an ion beam sputtering technique. Owing to its medical applications, the crystalline phases present in the HA must be controlled. This study investigated the effect of post-deposition heat treatment at different temperatures and evaluated the microstructure of the HA coatings and their behaviours in simulated body fluid (SBF). The post-deposition treatment of the as-deposited samples was carried out in an air-circulated furnace at a temperature between 3000C and 6000C. The XRD patterns reveal that the minimum temperature to transform the HA coating from amorphous to crystalline phase is 4000C. A higher temperature at 6000C leads to a growth of the crystalline HA phases. Fourier transform infrared spectroscopy (FTIR) measurements show the existence of hydroxyl and PO-bonds in all coatings and the amounts varied with temperature. Atomic Force Microscopy (AFM) study suggests that the nanostructured crystalline HA starts to grow at 4000C and becomes more obvious at a higher temperature of 6000C. The simulated body fluid (SBF) test reveals that better apatite formation with post deposition heat treatment at 6000C would potentially enhance the formation of new bone (osseointegration).

Sign in / Sign up

Export Citation Format

Share Document