scholarly journals Effect of Thermal Modification on the Nano-Mechanical Properties of the Wood Cell Wall and Waterborne Polyacrylic Coating

Forests ◽  
2020 ◽  
Vol 11 (12) ◽  
pp. 1247
Author(s):  
Yan Wu ◽  
Xinyu Wu ◽  
Feng Yang ◽  
Haiqiao Zhang ◽  
Xinhao Feng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Contact Angle ◽  
Cell Wall ◽  
Wood Cell Wall ◽  
Pinus Massoniana ◽  
Treatment Temperature ◽  
Thermal Modification ◽  
Composition Analysis ◽  
Masson Pine ◽  
Heat Treated

Masson pine (Pinus massoniana Lamb.) samples were heat-treated at different treatment temperatures (150, 170, and 190 °C), and the nano-mechanical properties of the wood cell wall, which was coated with a waterborne polyacrylic (WPA) lacquer product, were compared. The elastic modulus (Er) and hardness (H) of wood cell wall and the coating were measured and characterized by nanoindentation, and the influencing factors of mechanical properties during thermal modification were investigated by chemical composition analysis, contact angle analysis, and colorimetric analysis. The results showed that with the increase in the heat treatment temperature, the contact angle of the water on the wood’s surface and the colorimetric difference increased, while the content of the cellulose and hemicelluloses decreased. After thermal modification of 190 °C, the Er and H of the wood cell wall increased by 13.9% and 17.6%, respectively, and the Er and H of the WPA coating applied to the wood decreased by 12.1% and 22.2%. The Er and H of the interface between the coating and wood were lower than those near the coating’s surface. The Er and H of the cell wall at the interface between the coating and wood were lower than those far away from the coating. This study was of great significance for understanding the binding mechanism between coating and wood cell walls and improving the finishing technology of the wood materials after thermal modification.

scholarly journals Microstructure of thermally modified radiata pine wood

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 1523-1533
Author(s):  
José Luis Cabezas-Romero ◽  
Linette Salvo-Sepúlveda ◽  
Helga Contreras-Moraga ◽  
Natalia Pérez-Peña ◽  
Víctor Sepúlveda-Villarroel ◽  
...  
Keyword(s):  
Cell Wall ◽  
Wood Cell Wall ◽  
Morphological Changes ◽  
Untreated Wood ◽  
Radiata Pine ◽  
Treatment Temperature ◽  
Thermal Modification ◽  
Modification Process ◽  
Potential Alternative ◽  
Two Temperatures

The thermal modification of wood is a potential alternative method for improving wood dimensional stability and increasing the resistance of wood to decay. However, during thermal modification, morphological changes occur within the microstructure of the cell, and these confer different properties to the wood. This study investigated the effects of the thermal modification process on the microstructure of radiata pine juvenile wood. Therefore, anatomical measurements were performed via optical microscopy in selected earlywood and latewood samples after each treatment, and the results were compared to untreated wood samples. In this study, two temperatures (190 °C and 210 °C) were considered for the thermal modification process. The results showed that the level of temperature of modification affected to microstructure of cell wall. The cell wall thickness decreased as treatment temperature increased, whereas the average lumen diameter increased slightly as temperature increased. Thermally modified radiata pine showed signs of damage (cracks, broken cells and deformations in the wood cell wall). The proportion of destroyed area increased as temperature increased, and significant differences were evident for the thermal treatment at 210 °C.

scholarly journals Multi-Scale Evaluation of the Effect of Phenol Formaldehyde Resin Impregnation on the Dimensional Stability and Mechanical Properties of Pinus Massoniana Lamb.

Forests ◽  
2019 ◽  
Vol 10 (8) ◽  
pp. 646 ◽  
Author(s):  
Wang ◽  
Chen ◽  
Xie ◽  
Cai ◽  
Yuan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Dimensional Stability ◽  
Cell Walls ◽  
Phenol Formaldehyde ◽  
Pinus Massoniana ◽  
Swelling Properties ◽  
Masson Pine ◽  
Pine Wood ◽  
Pinus Massoniana Lamb

The local chemistry and mechanics of the control and phenol formaldehyde (PF) resin modified wood cell walls were analyzed to illustrate the modification mechanism of wood. Masson pine (Pinus massoniana Lamb.) is most widely distributed in the subtropical regions of China. However, the dimensional instability and low strength of the wood limits its use. Thus, the wood was modified by PF resin at concentrations of 15%, 20%, 25%, and 30%, respectively. The density, surface morphology, chemical structure, cell wall mechanics, shrinking and swelling properties, and macro-mechanical properties of Masson pine wood were analyzed to evaluate the modification effectiveness. The morphology and Raman spectra changes indicated that PF resin not only filled in the cell lumens, but also penetrated into cell walls and interacted with cell wall polymers. The filling and diffusing of resin in wood resulted in improved dimensional stability, such as lower swelling and shrinking coefficients, an increase in the elastic modulus (Er) and hardness (H) of wood cell walls, the hardness of the transverse section and compressive strength of the wood. Both the dimensional stability and mechanical properties improved as the PF concentration increased to 20%; that is, a PF concentration of 20% may be preferred to modify Masson pine wood.

Longitudinal mechanical properties of cell wall of Masson pine (Pinus massoniana Lamb) as related to moisture content: A nanoindentation study

Holzforschung ◽  
2011 ◽  
Vol 65 (1) ◽  
pp. 121-126 ◽  
Author(s):  
Yan Yu ◽  
Benhua Fei ◽  
Hankun Wang ◽  
Genlin Tian
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Moisture Content ◽  
Pinus Massoniana ◽  
Regression Equations ◽  
Saturation Point ◽  
Masson Pine ◽  
Pinus Massoniana Lamb ◽  
Experimental Values

Abstract The in situ imaging nanoindentation technique was used to investigate how the moisture content (MC) affects the longitudinal mechanical properties of Masson pine cell wall. Furthermore, nanoindentation tests in liquid water were performed. The results indicate that elastic modulus, hardness, and compression yield stress of wood wall are all linearly correlated to the selected MC region in the range from 4.5% to 13.1%. Remarkable differences were found between the experimental values measured in water and the extrapolated values based on regression equations below fiber saturation point.

Comparison of mechanical properties of thermally modified wood at growth ring and cell wall level by means of instrumented indentation tests

Holzforschung ◽  
2009 ◽  
Vol 63 (4) ◽  
Author(s):  
Stefanie Stanzl-Tschegg ◽  
Wilfried Beikircher ◽  
Dieter Loidl
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Thermal Treatment ◽  
Mechanical Performance ◽  
Growth Ring ◽  
Beech Wood ◽  
Thermal Modification ◽  
Wood Structure ◽  
Instrumented Indentation ◽  
Indentation Tests

Abstract Thermal modification is a well established method to improve the dimensional stability and the durability for outdoor use of wood. Unfortunately, these improvements are usually accompanied with a deterioration of mechanical performance (e.g., reduced strength or higher brittleness). In contrast, our investigations of the hardness properties in the longitudinal direction of beech wood revealed a significant improvement with thermal modification. Furthermore, we applied instrumented indentation tests on different hierarchical levels of wood structure (growth ring and cell wall level) to gain closer insights on the mechanisms of thermal treatment of wood on mechanical properties. This approach provides a variety of mechanical data (e.g., elastic parameters, hardness parameters, and viscoelastic properties) from one single experiment. Investigations on the influence of thermal treatment on the mechanical properties of beech revealed similar trends on the growth ring as well as the on the cell wall level of the wood structure.

scholarly journals Enhancement of the physical and mechanical properties of wood using a novel organo-montmorillonite/hyperbranched polyacrylate emulsion

Holzforschung ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Jianfeng Xu ◽  
Xiaoyan Li ◽  
Ling Long ◽  
Ru Liu
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Pinus Radiata ◽  
Wood Sample ◽  
Wood Cell Wall ◽  
Physical And Mechanical Properties ◽  
Radiata Pine ◽  
Compact Structure ◽  
Populus Cathayana ◽  
Modified Wood

AbstractIn this work, a novel waterborne hyperbranched polyacrylate (HBPA) dispersed organo-montmorillonite (OMMT) emulsion was synthesized and used for the treatment of wood in a vacuum environment in order to enhance the physical and mechanical properties of the wood. The sapwood of Cathay poplar (Populus cathayana Rehd.) and Radiata pine (Pinus radiata D.Don) were used as the samples for experimentation. The results showed that the physical and mechanical properties of the wood improved significantly due to the successful penetration of the OMMT and HBPA into the wood cell wall. From it was also observed that OMET completely exfoliated from the HBPA matrix and formed a hydrophobic film covering on the inside walls of the cell lumen. Further, it was observed that the poplar sample displayed better mechanical properties than the pine sample because the pine has a more compact structure when compared to poplar and contains rosin. Furthermore, it was also observed that the mechanical properties of the modified wood sample gradually improved with an increase in the concentration of the emulsion. However, excessive concentration (>4 wt%) did not lead to further improvement.

scholarly journals Influence of silicone oil thermal modification on mechanical properties of Masson pine wood

2021 ◽  
Vol 23 ◽  
Author(s):  
Kufre Edet Okon ◽  
Queen Aguma ◽  
Ebenezer Adeyemi Iyiola ◽  
Idiana-Abasi Kufre Okon
Keyword(s):  
Mechanical Properties ◽  
Silicone Oil ◽  
Thermal Modification ◽  
Masson Pine ◽  
Pine Wood

scholarly journals Investigation of intercritical heat treatment temperature effect on microstructure and mechanical properties of dual phase (DP) steel

10.30544/293 ◽  
2017 ◽  
Vol 23 (2) ◽  
pp. 143-152
Author(s):  
Mohammad Davari ◽  
Mehdi Mansouri Hasan Abadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Work Hardening ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Dual Phase ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Heat Treated ◽  
Intercritical Heat Treatment

In the present study, the effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferritic-martensitic dual-phase steel have been investigated utilizing tensile test, microhardness measurement and microscopic observation. Plain carbon steel sheet with a thickness of 2 mm was heat treated at 760, 780, 800, 820 and 840 °C intercritical temperatures. The results showed that martensite volume fraction (Vm) increases from 32 to 81%with increasing temperature from 760 to 840 °C. The mechanical properties of samples were examined by tensile and microhardness tests. The results revealed that yield strength was increased linearly with the increase in Vm, but the ultimate strength was increased up to 55% Vm and then decreased afterward. Analyzing the work hardening behavior in term of Hollomon equation showed that in samples with less than 55% Vm, the work hardening took place in one stage and the work hardening exponent increased with increasing Vm. More than one stage was observed in the work hardening behavior when Vm was increased. The results of microhardness test showed that microhardness of the martensite is decreased by increase in heat treatment temperature while the ferrite microhardness is nearly constant for all heat-treated samples.

Sign in / Sign up

Export Citation Format

Share Document