scholarly journals A New Approach for Characterizing Pile Heat Exchangers Using Thermal Response Tests

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3375
Author(s):  
Charles Maragna ◽  
Fleur Loveridge
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Thermal Response ◽  
Cost Effective ◽  
Thermal Capacity ◽  
Study Data ◽  
Design Parameters ◽  
Test Duration ◽  
Ground Source

Pile heat exchangers offer a cost effective route to implementation of ground-source heat pump systems for many large commercial buildings compared with traditional boreholes. Such projects typically use thermal response tests to determine the key input parameters for system design, namely soil thermal conductivity and heat exchanger thermal resistance. However, this brings challenges for pile heat exchanger based systems, where in situ thermal response tests are known to be less reliable due to the large thermal capacity of the pile. This paper presents a new “black box” resistance capacitive model for applications to pile thermal response tests. The approach is tested against case study data and shown to perform well. Additional test duration savings are shown to be possible if a novel combination of borehole and pile thermal response tests is applied together to determine design parameters.

Heat Exchanger Options for Dry Air Cooling for the sCO2 Brayton Cycle

2017 ◽  
Author(s):  
Anton Moisseytsev ◽  
Qiuping Lv ◽  
James J. Sienicki
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cost Effective ◽  
Finned Tube ◽  
Air Cooling ◽  
Brayton Cycle ◽  
Dry Air ◽  
Air Atmosphere ◽  
Air Cooler ◽  
Forced Air

The capability to utilize dry air cooling by which heat is directly rejected to the air atmosphere heat sink is one of the benefits of the supercritical carbon dioxide (sCO2) energy conversion cycle. For the selection and analysis of the heat exchanger options for dry air cooling applications for the sCO2 cycle, two leading forced air flow design approaches have been identified and analyzed for this application; an air cooler consisting of modular finned tube air coolers; and an air cooler consisting of modular compact diffusion-bonded heat exchangers. The commercially available modular finned tube air cooler is found to be more cost effective and is selected as the reference for dry air cooling.

scholarly journals Simulation of the effectiveness of longitudinal rectangular fins on the efficiency of the double pipe heat exchanger

2019 ◽  
Vol 21 (4) ◽  
pp. 48-57
Author(s):  
N. F. Timerbaev ◽  
A. K. Ali ◽  
Omar Abdulhadi Mustafa Almohamed ◽  
A. R. Koryakin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cold Water ◽  
Tube Diameter ◽  
Hot Water ◽  
Outer Tube ◽  
Design Parameters ◽  
Double Pipe ◽  
Central Pipe ◽  
Pipe Heat

In this article, a mathematical simulation of a double pipe heat exchanger is carried out, having the longitudinal rectangular fins with the dimension of (2*3*1000) mm, mounted on the outer surface of the inner tube of the heat exchanger. In this paper, the advantage of using of that type of fins and its effect on the effectiveness of the heat exchanger are studied with the help of the computer program. The carried out research allowsmaking the calculation to find the optimum design parameters of heat exchangers. The outer tube diameter is (34.1mm) while the inner tube diameter is (16.05mm). The tubes wall thickness is (1.5mm) and the model length was (1 m). The hot water is flowing through the inner tube in parallel with the cold water that passing the outer tube. The hot and cold water temperature at the inlet is (75°C & 30°C) respectively. The mass flow rate inside the central pipe is (0.1 kg/s) while the annular pipe carrying (0.3 kg/s). In the present work, the program ANSYS Workbench 15.0 was used to find out the results of heat transfer as well as the behavior of liquids inside the heat exchangers.

scholarly journals Method of Averaging the Effective Thermal Conductivity Based on Thermal Response Tests of Borehole Heat Exchangers

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3737
Author(s):  
Aneta Sapińska-Śliwa ◽  
Tomasz Sliwa ◽  
Kazimierz Twardowski ◽  
Krzysztof Szymski ◽  
Andrzej Gonet ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Effective Thermal Conductivity ◽  
Heat Exchangers ◽  
Thermal Response ◽  
Method Of Averaging ◽  
Thermal Response Test ◽  
Borehole Heat Exchanger ◽  
Measurement Results ◽  
Borehole Heat Exchangers

This work concerns borehole heat exchangers and their testing using apparatus for thermal response tests. In the theoretical part of the article, an equation was derived from the known equation of heat flow, on which the interpretation of the thermal response test was based. The practical part presents the results of several measurements taken in the AGH Laboratory of Geoenergetics. They were aimed at examining the potential heat exchange capacity between the heat carrier and rock mass. Measurement results in the form of graphs are shown in relation to the examined, briefly described wells. Result analysis made it possible to draw conclusions regarding the interpretation of the thermal response test. The method of averaging the measurement results was subjected to further study. The measuring apparatus recorded data at a frequency of one second, however such accuracy was too large to be analyzed efficiently. Therefore, an average of every 1 min, every 10 min, and every 60 min was proposed. The conclusions stemming from the differences in the values of effective thermal conductivity in the borehole heat exchanger, resulting from different data averaging, were described. In the case of three borehole heat exchangers, ground properties were identical. The effective thermal conductivity λeff was shown to depend on various borehole heat exchanger (BHE) designs, heat carrier flow geometry, and grout parameters. It is important to consider the position of the pipes relative to each other. As shown in the charts, the best (the highest) effective thermal conductivity λeff occurred in BHE-1 with a coaxial construction. At the same time, this value was closest to the theoretical value of thermal conductivity of rocks λ, determined on the basis of literature. The standard deviation and the coefficient of variation confirmed that the effective thermal conductivity λeff, calculated for different time intervals, showed little variation in value. The values of effective thermal conductivity λeff for each time interval for the same borehole exchanger were similar in value. The lowest values of effective thermal conductivity λeff most often appeared for analysis with averaging every 60 min, and the highest—for analysis with averaging every 1 min. For safety reasons, when designing (number of BHEs), safer values should be taken for analysis, i.e., lower, averaging every 60 min.

scholarly journals A Nodes-Based Non-Structural Model Considering a Series Structure for Heat Exchanger Network Synthesis

Processes ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 695
Author(s):  
Yue Xu ◽  
Heri Ambonisye Kayange ◽  
Guomin Cui
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Structural Model ◽  
Cost Effective ◽  
Maximum Energy ◽  
Network Synthesis ◽  
Heat Exchanger Network ◽  
Proposed Model ◽  
Effective Network ◽  
Heat Exchanger Network Synthesis

The aim of heat exchanger network synthesis is to design a cost-effective network configuration with the maximum energy recovery. Therefore, a nodes-based non-structural model considering a series structure (NNM) is proposed. The proposed model utilizes a simple principle based on setting the nodes on streams such that to achieve optimization of a heat exchanger network synthesis (HENS) problem. The proposed model uses several nodes to quantify the possible positions of heat exchangers so that the matching between hot and cold streams is random and free. Besides the stream splits, heat exchangers with series structures are introduced in the proposed model. The heuristic algorithm used to solve NNM model is a random walk algorithm with compulsive evolution. The proposed model is used to solve four scale cases of a HENS problem, the results show that the costs obtained by NNM model can be respectively lower 3226 $/a(Case 1), 11,056 $/a(Case 2), 2463 $/a(Case 3), 527 $/a(Case 4) than the best costs listed in literature.

Study on Engineering Construction with Three-Dimensional Heat Transfer Modeling for Double U-Tube Heat Exchangers in Ground-Source Heat Pump Systems

2013 ◽  
Vol 700 ◽  
pp. 231-234
Author(s):  
Lian Yang ◽  
Yong Hong Huang ◽  
Liu Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Three Dimensional ◽  
Ground Source Heat Pump ◽  
Ground Source Heat Pumps ◽  
Engineering Construction ◽  
Single Hole ◽  
Ground Source

There are many ground source heat pumps in engineering construction application. However, Research on heat exchanger models of single-hole buried vertical ground source heat pump mostly focuses on single U-tube ground heat exchangers other than double U-tube ones in China currently. Compared with single U-tubes, double U-tubes have the heat transfer particularity of asymmetry. Therefore, the use of the traditional single tube models would have large error in the simulation of the actual double U-tube heat exchangers. This paper frames a three-dimensional heat transfer model for the vertical single-hole buried double u-tube heat exchanger in a ground source heat pump system. The model considers the performance of U-bube material and uses a dual coordinate system and makes the control elemental volumes superimposed.

Analysis of the efficiency of hydrocarbon propellant cooling using liquid nitrogen and a combination of recuperative heat exchangers

2020 ◽  
Author(s):  
A.A. Aleksandrov ◽  
I.V. Barmin ◽  
A.V. Zolin ◽  
V.V. Chugunkov
Keyword(s):  
Heat Exchanger ◽  
Liquid Nitrogen ◽  
Coming Out ◽  
Heat Exchangers ◽  
Cooling System ◽  
Design Parameters ◽  
Nitrogen Gas ◽  
Double Pipe ◽  
The Cost ◽  
Pipe Heat

The paper describes the propellant cooling system using liquid nitrogen and a combination of recuperative heat exchangers, including sections of the double pipe heat exchanger and a twisted heat exchanger located in a tank with antifreeze, cooled by nitrogen gas coming out of the sections of the double pipe heat exchanger. Mathematical models of cooling processes for two variants of movement of propellant and liquid nitrogen in the channels of the double pipe heat exchanger sections are considered. Their using makes it possible to analyze the efficiency of propellant cooling operations depending on its mass, design parameters of the system tanks and heat exchangers, consumption characteristics of nitrogen and propellant, as well as to predict the required mass of liquid nitrogen and the time of propellant cooling during the operation of launching complex propellant-feed systems. Calculated dependences and simulation results of propellant and antifreeze cooling in a tank with a twisted heat exchanger are presented. The influence of variants of arranging propellant cooling processes and liquid nitrogen consumption on the efficiency of the cooling system is analyzed. Comparing to the available systems the capability of reducing the cost of liquid nitrogen are identified as well as reducing time of the propellant cooling operations by means of equipping launch complexes.

The Concept Design of Tornado Like Jet Condenser Heat Exchanger

2013 ◽  
Author(s):  
G. I. Kiknadze ◽  
I. A. Gachechiladze ◽  
T. T. Barnaveli
Keyword(s):  
Heat Exchanger ◽  
Heat Exchangers ◽  
Continuous Medium ◽  
Cost Effective ◽  
Self Organization ◽  
Concept Design ◽  
Resource Saving ◽  
Heat And Mass Exchange ◽  
Double Curvature ◽  
Functional Efficiency

The concept design and fabrication of cost-effective and resource-saving Tornado Like Jet Condensers Heat Exchangers is described. Tornado Like Jet (TLJ) Technologies are utilizing the features of the streams of the continuous medium over the surfaces with dimples of double curvature inducing the secondary twisted vortexes self organization. (TLJ) Technologies are characterized by high functional efficiency of heat and mass exchange. The project is based on theoretical and experimental results obtained by the authors of the project in past years in development of a (TLJ) Technologies package.

scholarly journals Thermal performance of the ground in geothermal pavements

2020 ◽  
Vol 205 ◽  
pp. 06015
Author(s):  
Yaser Motamedi ◽  
Nikolas Makasis ◽  
Arul Arulrajah ◽  
Suksun Horpibulsuk ◽  
Guillermo Narsilio
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Thermal Response ◽  
Geothermal Heat ◽  
Capital Costs ◽  
Ground Source ◽  
Shallow Geothermal Energy ◽  
Novel Concept ◽  
Response Testing ◽  
The Impact

Shallow geothermal energy utilises the ground at relatively shallow depths as a heat source or sink to efficiently heat and cool buildings. Geothermal pavement systems represent a novel concept where horizontal ground source heat pump systems (GSHP) are implemented in pavements instead of purpose-built trenches, thus reducing their capital costs. This paper presents a geothermal pavement system segment (20m × 10m) constructed and monitored in the city of Adelaide, Australia, as well as thermal response testing (TRT) results. Pipes have been installed in the pavement at 0.5 m depth, and several thermistors have been placed on the pipes and in the ground. A TRT has been performed with 6kW heating load to achieve an understanding of the thermal response of the system as well as to estimate the effective thermal conductivity of the ground. The results show that the conventional semi-log method may be applicable to determine the thermal conductivity for geothermal pavements. The geothermal heat exchanger at shallow depth is considerably under the influence of the ambient temperature; however, it is still acceptable for exchanging the heat within the ground. It is also concluded that the impact radius of heat exchanger in geothermal pavement during the TRT is around 0.5m in the vertical and horizontal directions for this case study.

scholarly journals Field Test and Numerical Simulation on Heat Transfer Performance of Coaxial Borehole Heat Exchanger

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5471
Author(s):  
Peng Li ◽  
Peng Guan ◽  
Jun Zheng ◽  
Bin Dou ◽  
Hong Tian ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Properties ◽  
Heat Exchanger ◽  
Flow Rate ◽  
Thermal Response ◽  
Heat Pumps ◽  
Inlet Temperature ◽  
Borehole Heat Exchanger ◽  
Ground Source Heat Pumps ◽  
Ground Source

Ground thermal properties are the design basis of ground source heat pumps (GSHP). However, effective ground thermal properties cannot be obtained through the traditional thermal response test (TRT) method when it is used in the coaxial borehole heat exchanger (CBHE). In this paper, an improved TRT (ITRT) method for CBHE is proposed, and the field ITRT, based on the actual project, is carried out. The high accuracy of the new method is verified by laboratory experiments. Based on the results of the ITRT and laboratory experiment, the 3D numerical model for CBHE is established, in which the flow directions, sensitivity analysis of heat transfer characteristics, and optimization of circulation flow rate are studied, respectively. The results show that CBHE should adopt the anulus-in direction under the cooling condition, and the center-in direction under the heating condition. The influence of inlet temperature and flow rate on heat transfer rate is more significant than that of the backfill grout material, thermal conductivity of the inner pipe, and borehole depth. The circulating flow rate of CBHE between 0.3 m/s and 0.4 m/s can lead to better performance for the system.

Sign in / Sign up

Export Citation Format

Share Document