scholarly journals Impacts of Mooring-Lines Hysteresis on Dynamic Response of Spar Floating Wind Turbine

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2109
Author(s):  
Weimin Chen ◽  
Shuangxi Guo ◽  
Yilun Li ◽  
Yijun Shen
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Wave Loads ◽  
Mooring Lines ◽  
Hysteresis Behavior ◽  
Floating Wind Turbine ◽  
Motion Responses ◽  
Element Method

Floating wind turbines often experience larger-amplitude motions caused by wind and ocean wave loads, while mooring-lines, such as catenary and taut mooring-lines, make the structure configurations along with an analysis of the global response more complicated compared to a fixed support foundation. Moreover, the restoring performance of dynamic mooring-lines exhibits a significant hysteresis behavior, and this hysteresis behavior may have profound impacts on the structural response of floating wind turbines under environmental loads. In this study, using the coupled finite element method, a dynamic simulation model is developed to study the motion responses of a spar floating wind turbine under consideration of mooring-lines hysteresis. In order to consider large-amplitude motion and nonlinear behaviors of catenary mooring-lines, a FEM (finite element method) model is developed based on a combination of 3D nonlinear beam elements and the super-element approach, and the interaction between mooring-lines and seabed is also included. Using our FEM numerical simulations, firstly, the restoring performance of mooring-lines and its hysteresis behavior are studied. Then, the motion responses, e.g., the displacements of the spar float undergoing various wave loads, are examined. The numerical results show that: the restoring stiffness of mooring-lines exhibits significant hysteresis behavior, and the restoring force is directionally dependent. Due to the hysteresis of restoring performance, for a case of regular wave conditions, little change of the spar surge in a steady-state is seen; however, for a case of extreme wave loads, the motion response gets about 14.4% smaller, compared with the quasi-static cases.

Analysis of Octagonal Pile Supporting Offshore Wind Turbines Under Wave Loads

2014 ◽  
Author(s):  
Serena Lim ◽  
Longbin Tao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Computational Cost ◽  
Offshore Wind ◽  
Computational Time ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Element Method

Offshore wind energy development has gained considerable momentum around the world as wind is stronger and steadier offshore compared to land. This has led to a significant increase in production in recent years, especially offshore wind turbine embedded in shallow waters, such as the recent large scale offshore wind farms in the Northern Europe region. Being at the offshore waters, the wind turbines are subjected to harsh environment. The pile supporting the wind turbine must be reliable and able to withstand such sea condition. It is an important part of the design to study the structural behaviour of the piles under the wave loads. Due to the significant capital cost associated with the fabrication of the large circular cylinders, a new recommended innovative design to overcome such problem is to substitute the circular cylinder with a vertical monopile of octagonal cross-sectional shape. This paper describes the development of an efficient numerical model for structural analysis of wave interaction with octagonal pile using a modified semi analytical Scaled Boundary Finite Element Method (SBFEM). In contrast to the existing solutions obtained using the traditional methods such as the Finite Element Method (FEM) which typically suffer from high computational cost and the Boundary Element Method (BEM) which faces limitation from fundamental equations and problems with singularities. The most prominent advantage that SBFEM has over the FEM is in terms of the number of elements used for calculation and hence a reduction in computational time. When compared with BEM, the SBFEM does not suffer from computational stability problems.

Static and Dynamic Characteristic Analysis of the Tower for Vertical Axis Wind Turbine Based on Finite Element Method

2012 ◽  
Vol 229-231 ◽  
pp. 613-616
Author(s):  
Yan Jue Gong ◽  
Yuan Yuan Zhang ◽  
Fu Zhao ◽  
Hui Yu Xiang ◽  
Chun Ling Meng ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Dynamic Characteristic ◽  
Optimization Design ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Characteristic Analysis ◽  
Support Structure ◽  
Element Method

As an important part of the vertical axis wind turbine, the support structure should have high strength and stiffness. This article adopts finite element method to model a kind of tower structure of the vertical axis wind turbine and carry out static and modal analysis. The static and dynamic characteristic results of tower in this paper provide reference for optimization design the support structure of wind turbine further.

scholarly journals Study of Floating Wind Turbine with Modified Tension Leg Platform Placed in Regular Waves

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 703 ◽  
Author(s):  
Juhun Song ◽  
Hee-Chang Lim
Keyword(s):  
Wind Turbine ◽  
Real Data ◽  
Offshore Wind ◽  
Scale Model ◽  
Offshore Wind Turbine ◽  
Wave Loads ◽  
Tension Leg Platform ◽  
Mooring Lines ◽  
Floating Wind Turbine ◽  
Wave Conditions

In this study, the typical ocean environment was simulated with the aim to investigate the dynamic response under various environmental conditions of a Tension Leg Platform (TLP) type floating offshore wind turbine system. By applying Froude scaling, a scale model with a scale of 1:200 was designed and model experiments were carried out in a lab-scale wave flume that generated regular periodic waves by means of a piston-type wave generator while a wave absorber dissipated wave energy on the other side of the channel. The model was designed and manufactured based on the standard prototype of the National Renewable Energy Laboratory (NREL) 5 MW offshore wind turbine. In the first half of the study, the motion and structural responses for operational wave conditions of the North Sea near Scotland were considered to investigate the performance of a traditional TLP floating wind turbine compared with that of a newly designed TLP with added mooring lines. The new mooring lines were attached with the objective of increasing the horizontal stiffness of the system and thereby reducing the dominant motion of the TLP platform (i.e., the surge motion). The results of surge translational motions were obtained both in the frequency domain, using the response amplitude operator (RAO), and in the time domain, using the omega arithmetic method for the relative velocity. The results obtained show that our suggested concept improves the stability of the platform and reduces the overall motion of the system in all degrees-of-freedom. Moreover, the modified design was verified to enable operation in extreme wave conditions based on real data for a 100-year return period of the Northern Sea of California. The loads applied by the waves on the structure were also measured experimentally using modified Morison equation—the formula most frequently used to estimate wave-induced forces on offshore floating structures. The corresponding results obtained show that the wave loads applied on the new design TLP had less amplitude than the initial model and confirmed the significant contribution of the mooring lines in improving the performance of the system.

scholarly journals Study on the Effect of Different Delamination Defects on Buckling Behavior of Spar Cap in Wind Turbine Blade

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Jianwei Li ◽  
Jinghua Wang ◽  
Leian Zhang ◽  
Xuemei Huang ◽  
Yongfeng Yu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Reference Value ◽  
Element Model ◽  
Theory And Practice ◽  
The Finite Element Method ◽  
Buckling Behavior ◽  
Element Method

Delamination is detrimental to the composite materials, and it may occur in the manufacturing process of the unidirectional laminate of the spar cap in wind turbine blades. This paper studies the effect of different delamination defects on the strength of the unidirectional laminate. The finite element model of laminate with different delamination areas and delamination heights is established using solid elements. The eigenvalues of laminates have different parameters calculated based on the finite element method. The final coupon test is used to verify the conclusions of simulation results. The finite element method presented in this study shows excellent capabilities to predict the buckling behavior of the laminate. The buckling eigenvalue of tested laminate is negatively correlated with the delamination area and positively correlated with the delamination height under the edgewise load. The S11, which is too high at the boundary of the delamination region, plays a significant role in buckling failure. It has a particular reference value for testing the laminate of blade both in theory and practice.

scholarly journals Proposal of a Novel Mooring System Using Three-Bifurcated Mooring Lines for Spar-Type Off-Shore Wind Turbines

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8303
Author(s):  
Shi Liu ◽  
Yi Yang ◽  
Chengyuan Wang ◽  
Yuangang Tu ◽  
Zhenqing Liu
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Line Length ◽  
Torsional Stiffness ◽  
Irregular Waves ◽  
Mooring Line ◽  
Mooring System ◽  
The Novel ◽  
Mooring Lines ◽  
Floating Wind Turbine

Floating wind turbine vibration controlling becomes more and more important with the increase in wind turbine size. Thus, a novel three-bifurcated mooring system is proposed for Spar-type floating wind turbines. Compared with the original mooring system using three mooring lines, three-bifurcated sub-mooring-lines are added into the novel mooring system. Specifically, each three-bifurcated sub-mooring-line is first connected to a Spar-type platform using three fairleads, then it is connected to the anchor using the main mooring line. Six fairleads are involved in the proposed mooring system, theoretically resulting in larger overturning and torsional stiffness. For further improvement, a clump mass is attached onto the main mooring lines of the proposed mooring system. The wind turbine surge, pitch, and yaw movements under regular and irregular waves are calculated to quantitatively examine the mooring system performances. A recommended configuration for the proposed mooring system is presented: the three-bifurcated sub-mooring-line and main mooring line lengths should be (0.0166, 0.0111, 0.0166) and 0.9723 times the total mooring line length in the traditional mooring system. The proposed mooring system can at most reduce the wind turbine surge movement 37.15% and 54.5% when under regular and irregular waves, respectively, and can at most reduce the yaw movement 30.1% and 40% when under regular and irregular waves, respectively.

scholarly journals Diseño y simulación preliminar del cubo del rotor para una turbina eólica de 50-kW clase II, de acuerdo a la norma IEC-61400-2

2020 ◽  
pp. 1-13
Author(s):  
José Luis Colín-Martínez ◽  
Victor Lopez-Garza ◽  
Isaac Hernández-Arriaga ◽  
María Guadalupe Navarro-Rojero
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Farms ◽  
The Finite Element Method ◽  
Ansys Software ◽  
International Standard ◽  
Previous Design ◽  
Element Method

Currently, wind energy in Mexico is growing and the same is happening worldwide, so projects with national technologies for the manufacture of wind turbine components must be developed. In this work, a proposal is made for the design of the hub of the rotor for a 50-kW turbine, the objective is to make a new proposal to improve the previous design of project P07 of the Centro Mexicano de Innovación en Energía Eólica (CEMIEEólico), which has a welded mechanical hub for a prototype turbine 30 kW. In addition, a simulation is performed through analysis of the finite element method (FEA) by applying certain load elements with the simplified load method of the international standard IEC 61400-2. In these simulations, the load cases of the norm that directly influence the cube are analyzed, then simulated in the ANSYS software to validate the proposed design, mainly analyzing the stresses and deformations. The results obtained will serve as a reference to manufacture the cube and evaluate the feasibility of carrying out a commercial stage with a view to making national components for wind farms.

scholarly journals Fracture analysis and improvement of the main shaft of wind turbine based on finite element method

2018 ◽  
Vol 10 (4) ◽  
pp. 168781401876900 ◽  
Author(s):  
Ruiming Wang ◽  
Tian Han ◽  
Wenrui Wang ◽  
Yang Xue ◽  
Deyi Fu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Wind Turbine ◽  
Fracture Analysis ◽  
Main Shaft ◽  
Element Method
Sign in / Sign up

Export Citation Format

Share Document