scholarly journals Calorimetric Behaviour of Electric Cables

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1007
Author(s):  
Katarzyna Kaczorek-Chrobak ◽  
Jadwiga Fangrat ◽  
Bartłomiej K. Papis
Keyword(s):  
Heat Flux ◽  
Vinyl Chloride ◽  
Cone Calorimeter ◽  
Large Scale ◽  
Radiant Heat ◽  
Small Scale ◽  
Power Cable ◽  
Standard Fire ◽  
Poly Vinyl Chloride ◽  
Fire Modelling

A routine cone calorimeter procedure, the theoretical analysis method, based on a set of ignitability data from the cone calorimeter, has been performed. The five sets of ignition times at different irradiance levels were used for obtaining experimental data needed for analysis. The cone calorimeter tests were performed with horizontal specimens of the size 100 mm × 100 mm consisting of eight pieces of commercial poly(vinyl chloride) coaxial power cable. Specimen combustion was carried out under external heat flux of constant values equal to 10, 20, 30, 40 and 50 kW·m−2, respectively. Standard fire parameters and time to ignition were used for analysis. The results indicate that for each fire parameter, a rising trend with an increase in radiant heat flux has been observed. It was shown that the use of poly(vinyl chloride)-based cables is a potential fire safety hazard due to the emission of heat and a large amount of acid smoke. Quintiere’s theory has been shown as a useful tool for fire modelling by using the data from small-scale tests rather than large geometrical scale cable experiments. Large scale cable test (EN 50399) results are also presented and compared with cone calorimeter data.

scholarly journals Response of stone wool–insulated building barriers under severe heating exposures

2018 ◽  
Vol 36 (4) ◽  
pp. 315-341 ◽  
Author(s):  
Blanca Andres ◽  
Karlis Livkiss ◽  
Juan P Hidalgo ◽  
Patrick van Hees ◽  
Luke Bisby ◽  
...  
Keyword(s):  
Heat Flux ◽  
Large Scale ◽  
Air Entrainment ◽  
Radiant Heat ◽  
Mechanical Degradation ◽  
Radiant Heat Flux ◽  
System A ◽  
Radiant Panel ◽  
Stone Wool ◽  
Temperature Exposure

This article presents the experimental results of stone wool–layered sandwich constructions, with either steel or gypsum claddings, tested under four different heating exposures: 7 kW/m2 incident radiant heat flux exposure, 60 kW/m2 incident radiant heat flux exposure, parametric time–temperature curve exposure and ISO 834 standard time–temperature exposure. The test apparatus used were a movable radiant panel system, a mid-scale furnace (1.5 m3) and a large-scale furnace (15 m3). The results show that reduced-scale tests are capable of reproducing the heat transferred through the construction at large scale provided there is limited mechanical degradation. The results indicate that the availability of oxygen is fundamental to the fire behaviour of the sandwich composites tested. Reactions occurring in stone wool micro-scale testing, such as oxidative combustion of the binder or crystallisation of the fibres, have a limited effect on the temperature increase when wool is protected from air entrainment.

Modeling the Impact of Convective Entrainment on the Tropical Tropopause

2006 ◽  
Vol 63 (3) ◽  
pp. 1013-1027 ◽  
Author(s):  
F. J. Robinson ◽  
S. C. Sherwood
Keyword(s):  
Heat Flux ◽  
Large Scale ◽  
Small Scale ◽  
Entrainment Rate ◽  
Subgrid Scale ◽  
Turbulence Parameterization ◽  
Tropical Tropopause ◽  
Scale Turbulence ◽  
Cold Point ◽  
The Impact

Abstract Simulations with the Weather Research and Forecasting (WRF) cloud-resolving model of deep moist convective events reveal net cooling near the tropopause (∼15–18 km above ground), caused by a combination of large-scale ascent and small-scale cooling by the irreversible mixing of turbulent eddies overshooting their level of neutral buoyancy. The turbulent cooling occurred at all CAPE values investigated (local peak values ranging from 1900 to 3500 J kg−1) and was robust to grid resolution, subgrid-scale turbulence parameterization, horizontal domain size, model dimension, and treatment of ice microphysics. The ratio of the maximum downward heat flux in the tropopause to the maximum tropospheric upward heat flux was close to 0.1. This value was independent of CAPE but was affected by changes in microphysics or subgrid-scale turbulence parameterization. The convective cooling peaked roughly 1 km above the cold point in the background input sounding and the mean cloud- and (turbulent kinetic energy) TKE-top heights, which were all near 16.5 km above ground. It was associated with turbulent entrainment of stratospheric air from as high as 18.25 km into the troposphere. Typical cooling in the experiments was of order 1 K during convective events that produced order 10 mm of precipitation, which implied a significant contribution to the tropopause energy budget. Given the sharp concentration gradients and long residence times near the cold point, even such a small entrainment rate is likely consequential for the transport and ambient distribution of trace gases such as water vapor and ozone, and probably helps to explain the gradual increase of ozone typically observed below the tropical tropopause.

Modeling Exposures of a Nylon-Cotton Fabric to High Radiant Heat Flux

2016 ◽  
Vol 11 (3) ◽  
pp. 155892501601100
Author(s):  
Thomas Godfrey ◽  
Margaret Auerbach ◽  
Gary Proulx ◽  
Pearl Yip ◽  
Michael Grady
Keyword(s):  
Heat Flux ◽  
Cone Calorimeter ◽  
Burn Injury ◽  
Thermal Protection ◽  
Transient Heat Conduction ◽  
Radiant Heat ◽  
Heat Fluxes ◽  
Direct Result ◽  
Face Modeling ◽  
Flaming Combustion

American soldiers and marines involved in the recent conflicts in Iraq and Afghanistan have suffered increased incidence of burn injury, often as a direct result of exposure to improvised explosive devices. In this work, a one dimensional numerical pyrolysis model for transient heat conduction, incorporating material transformations described by chemical kinetics, is used to investigate the response of the standard 230 g/m2 Army Combat Uniform (ACU) fabric to high radiant heat fluxes in short duration thermal protection tests and long duration cone calorimeter tests. Thermal protection tests are performed using a Thermal Barrier Test Apparatus–an automated device, incorporating a closed-loop controlled IR radiant heat source, automated water cooled shutter, a fabric sample holder, an adjustable stage with a water cooled Schmidt-Boelter heat flux gauge and a PC based data acquisition system. Cone calorimeter tests are performed on fabric specimens at an exposure heat flux of 25 kW/m2. In thermal protection tests involving exposures of 90 kW/m2 for five seconds and 77 kW/m2 for four seconds, modeling indicated that desorption and evaporation of moisture content has an important effect, but melting of the nylon component and material decomposition had insignificant effects on the heat flux transmitted through the fabric back face. Modeling results for cone testing exhibited good agreement for time to ignition and duration of flaming combustion.

INVESTIGATION INTO THE INFLUENCE OF IMPREGNATION ON PINE TIMBER COMBUSTION USING A CONE CALORIMETER AND LARGE SCALE TESTS

2011 ◽  
Vol 3 (3) ◽  
pp. 91-104 ◽  
Author(s):  
Jerzy Gałaj ◽  
Zbignev Karpovič ◽  
Waldemar Jaskółowski
Keyword(s):  
Cone Calorimeter ◽  
Large Scale ◽  
Experimental Studies ◽  
Fire Retardant ◽  
Full Scale ◽  
Lower Amount ◽  
Small Scale ◽  
Fire Retardants ◽  
Co Concentration ◽  
Piloted Ignition

Fire safety is one of the main requirements with respect to the regulations on the buildings involved into the category of human hazards. Human safety measures are applied equally to inhabitants, users, customers, spectators, etc., as well as to fire brigades taking part in the activities connected with rescue actions. Methods for emission research were applied to estimate thermo-kinetic parameters related to smoke and toxic gases. The methods fall into two types: full scale methods reflect fire conditions and small laboratory scale methods having a significantly lower degree of reflection. This paper presents the results of studies on the influence of BAK-1 and Flamasepas-2 fire retardants produced in Lithuania and applied for timber on the selected parameters of the fire environment. Experimental studies were conducted using a cone calorimeter (small scale) in the closed compartment equipped with measuring devices (full scale). The undertaken studies have demonstrated that considering some parameters, such as heat release rate (HRR), a positive effect of the lower amount of the released heat can be obtained. Unfortunately, in case of the major part of the studied parameters, including time to ignition, CO concentration and extinction parameter reflecting smokiness, worse results (shorter time, higher CO values and higher extinction coefficient) have been observed for the treated timber rather than for the non-impregnated one. The obtained results have showed combustion with piloted ignition. In case of no piloted ignition, the results were slightly different. For all studied specimens treated with fire retardants, no ignition was observed and tests were terminated following 15 minutes. CO concentration and extinction parameter (smokiness) were higher for non-impregnated timber. Full scale experiments have confirmed the above provided information; moreover, it has been found that the application of fire retardant has no significant impact on temperatures in the compartment.

Three-dimensional vorticity, momentum and heat transport in a turbulent cylinder wake

2016 ◽  
Vol 809 ◽  
pp. 135-167 ◽  
Author(s):  
J. G. Chen ◽  
Y. Zhou ◽  
T. M. Zhou ◽  
R. A. Antonia
Keyword(s):  
Heat Flux ◽  
Heat Transport ◽  
Large Scale ◽  
Three Dimensional ◽  
Heat Diffusion ◽  
Small Scale ◽  
Stream Velocity ◽  
Streamwise Vorticity ◽  
Spanwise Vortex ◽  
D 20

The transport of momentum and heat in the turbulent intermediate wake of a circular cylinder is inherently three-dimensional (3-D). This work aims to gain new insight into the 3-D vorticity structure, momentum and heat transport in this flow. All three components of the velocity and vorticity vectors, along with the fluctuating temperature, are measured simultaneously, at nominally the same point in the flow, with a probe consisting of four X-wires and four cold wires. Measurements are made in the ($x$,$y$) or mean shear plane at$x/d=10$, 20 and 40 at a Reynolds number of$2.5\times 10^{3}$based on the cylinder diameter$d$and the free-stream velocity. A phase-averaging technique is developed to separate the large-scale coherent structures from the remainder of the flow. It is found that the effects of vorticity on heat transport at$x/d=10$and$x/d=20{-}40$are distinctly different. At$x/d=10$, both spanwise and streamwise vorticity components account significantly for the heat flux. At$x/d=20$and 40, the spanwise vortex rollers play a major role in inducing the coherent components of the heat flux vector, while the ribs are responsible for the small-scale heat diffusion out of the spanwise vortex rollers. The present data indicate that, if the spanwise-velocity-related terms are ignored, the estimated values of the production can have errors of approximately 22 % and 13 % respectively for the turbulent energy and temperature variance at$x/d=40$, and the errors are expected to further increase downstream. A conceptual model summarizing the 3-D features of the heat and momentum transports at$x/d=10$is proposed. Compared with the previous two-dimensional model of Matsumura & Antonia (J. Fluid Mech., vol. 250, 1993, pp. 651–668) or MA, the new model provides a more detailed description of the role the rib-like structures undertake in transporting heat and momentum, and also underlines the importance of the upstream half of the spanwise vortex rollers, instead of only one quadrant of these rollers, as in the MA model, in diffusing heat out of the vortex.

scholarly journals Effects of local advection on the spatial sensible heat flux variation on a mountain glacier

2016 ◽  
Vol 10 (6) ◽  
pp. 2887-2905 ◽  
Author(s):  
Tobias Sauter ◽  
Stephan Peter Galos
Keyword(s):  
Heat Flux ◽  
Large Scale ◽  
Flow Direction ◽  
Sensible Heat Flux ◽  
Heat Fluxes ◽  
Small Scale ◽  
Topographic Effects ◽  
Sensible Heat ◽  
Wind Fields ◽  
Mountain Glacier

Abstract. Distributed mass balance models, which translate micrometeorological conditions into local melt rates, have proven deficient to reflect the energy flux variability on mountain glaciers. This deficiency is predominantly related to shortcomings in the representation of local processes in the forcing data. We found by means of idealized large-eddy simulations that heat advection, associated with local wind systems, causes small-scale sensible heat flux variations by up to 100 Wm−2 during clear sky conditions. Here we show that process understanding at a few observation sites is insufficient to infer the wind and temperature distributions across the glacier. The glacier-wide hourly averaged sensible heat fluxes are both over- and underestimated by up to 16 Wm−2 when using extrapolated temperature and wind fields. The sign and magnitude of the differences depend on the site selection, which is used for extrapolation as well as on the large-scale flow direction. Our results demonstrate how the shortcomings in the local sensible heat flux estimates are related to topographic effects and the insufficient characterization of the temperature advection process.

scholarly journals Effect of the Cone Heater Scale Compliant with the ISO 5660 Standard on Spatial Uniformity of Radiant Heat Flux

2020 ◽  
Vol 34 (5) ◽  
pp. 27-33
Author(s):  
Sanghoon Ryu ◽  
Sun-Yeo Mun ◽  
Cheol-Hong Hwang
Keyword(s):  
Heat Flux ◽  
Heat Release ◽  
Cone Calorimeter ◽  
Large Deviation ◽  
Mass Loss Rate ◽  
Radiant Heat ◽  
Radiant Heat Flux ◽  
Spatial Uniformity ◽  
Measurement Results ◽  
Physical Quantities

Physical quantities such as mass loss rate, heat release rate, and total heat release are often measured through a cone calorimeter (a representative bench-scale apparatus) and are primarily considered as values per unit area. Hence, the uniformity of radiant heat flux supplied by the cone heater to the specimen is very important with respect to the measurement results’ validity. In this study, on the basis of the ISO 5660 standard, the uniformity of radiant heat flux at the specimen surface was evaluated for the cone heaters used with the cone calorimeter. It is observed that a normal cone heater (NCH) compliant with the ISO 5660-1 standard satisfies the requirement of uniformity within a range of ± 2% in the central 5 cm × 5 cm area, but it has a large deviation of approximately 13% at the position corresponding to the edge of the specimen. In addition, the duration of NCH usage does not significantly affect the distribution of radiant heat flux. Furthermore, it is observed that a large cone heater compliant with the ISO/TC 5660-4 standard can supply moderately-uniform radiant heat flux over the entire surface area (10 cm × 10 cm) of the specimen.

Large-scale fractionation of poly(vinyl chloride) and characterization of the fractions

1967 ◽  
Vol 11 (8) ◽  
pp. 1539-1552 ◽  
Author(s):  
G. Pezzin ◽  
G. Sanmartin ◽  
F. Zilio-Grandi
Keyword(s):  
Vinyl Chloride ◽  
Large Scale ◽  
Poly Vinyl Chloride
Sign in / Sign up

Export Citation Format

Share Document