scholarly journals Effect of Fins on the Internal Flow Characteristics in the Draft Tube of a Francis Turbine Model

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2806 ◽  
Author(s):  
Seung-Jun Kim ◽  
Young-Seok Choi ◽  
Yong Cho ◽  
Jong-Woong Choi ◽  
Jung-Jae Hyun ◽  
...  
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Low Flow ◽  
Francis Turbine ◽  
Vortex Rope ◽  
Turbine Model ◽  
Low Flow Rate

Undesirable flow phenomena in Francis turbines are caused by pressure fluctuations induced under conditions of low flow rate; the resulting vortex ropes with precession in the draft tube (DT) can degrade performance and increase the instability of turbine operations. To suppress these DT flow instabilities, flow deflectors, grooves, or other structures are often added to the DT into which air or water is injected. This preliminary study investigates the effects of anti-cavity fins on the suppression of vortex ropes in DTs without air injection. Unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted using a scale-adaptive simulation shear stress transport turbulence model to observe the unsteady internal flow and pressure characteristics by applying anti-cavity fins in the DT of a Francis turbine model. A vortex rope with precession was observed in the DT under conditions of low flow rate, and the anti-cavity fins were confirmed to affect the mitigation of the vortex rope. Moreover, at the low flow rate conditions under which the vortex rope developed, the application of anti-cavity fins was confirmed to reduce the maximum unsteady pressure.

scholarly journals Effect of Air Injection on the Internal Flow Characteristics in the Draft Tube of a Francis Turbine Model

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1182
Author(s):  
Seung-Jun Kim ◽  
Yong Cho ◽  
Jin-Hyuk Kim
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Air Injection ◽  
Low Flow ◽  
Francis Turbine ◽  
Navier Stokes ◽  
Vortex Rope

Under low flow-rate conditions, a Francis turbine exhibits precession of a vortex rope with pressure fluctuations in the draft tube. These undesirable flow phenomena can lead to deterioration of the turbine performance as manifested by torque and power output fluctuations. In order to suppress the rope with precession and a swirl component in the tube, the use of anti-swirl fins was investigated in a previous study. However, vortex rope generation still occurred near the cone of the tube. In this study, unsteady-state Reynolds-averaged Navier–Stokes analyses were conducted with a scale-adaptive simulation shear stress transport turbulence model. This model was used to observe the effects of the injection in the draft tube on the unsteady internal flow and pressure phenomena considering both active and passive suppression methods. The air injection affected the generation and suppression of the vortex rope and swirl component depending on the flow rate of the air. In addition, an injection level of 0.5%Q led to a reduction in the maximum unsteady pressure characteristics.

Inter-Blade Vortex Characteristics With the Blockage Effects of Runner Blade in a Francis Hydro Turbine Model

2019 ◽  
Author(s):  
Seung-Jun Kim ◽  
Jin-Hyuk Kim ◽  
Young-Seok Choi ◽  
Yong Cho ◽  
Jong-Woong Choi
Keyword(s):  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Operating Conditions ◽  
Low Flow ◽  
Hydro Turbine ◽  
Runner Blade ◽  
Performance Reduction ◽  
Turbine Model ◽  
Low Flow Rate

Abstract This study presents the numerical analysis on the inter-blade vortex characteristics along with the blockage effects of runner blade in a Francis hydro turbine model with various flow rate conditions. The turbine model showed different flow characteristics in the runner blade passages according to operating conditions, and inter-blade vortex was observed at lower flow rate conditions. This inter-blade vortex can lead to performance reduction, vibration, and instability for smooth operation of turbine systems. The previous study on blockage effects on various runner blade thickness, showed its influence on hydraulic performance and internal flow characteristics at low flow rate conditions. Therefore, the inter-blade vortex characteristics can be altered with the blockage effects at low flow rate conditions in a Francis hydro-turbine. For investigating the internal flow and unsteady pressure characteristics, three-dimensional steady and unsteady Reynolds-averaged Navier-Stokes calculations are performed. These inter-blade vortices were captured at the leading and trailing edges close to the runner hub. These vortex regions showed flow separation and stagnation flow while blockage effects contributed for decreasing the inter-blade vortex at low flow rate conditions.

scholarly journals Unsteady Characteristics of Forward Multi-Wing Centrifugal Fan at Low Flow Rate

Processes ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 691 ◽  
Author(s):  
Lun ◽  
Ye ◽  
Lin ◽  
Ying ◽  
Wei
Keyword(s):  
Unsteady Flow ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Boundary Layer Separation ◽  
Low Flow ◽  
Centrifugal Fan ◽  
Suction Surface ◽  
Cfd Method ◽  
Low Flow Rate

The unsteady flow characteristics of a forward multi-wing centrifugal fan under a low flow rate are studied using the computational fluid dynamics (CFD) method. This paper emphasizes the eddy current distribution in terms of the Q criterion method, as well as pressure fluctuation, frequency spectrum, and kinetic energy spectrum analysis of internal monitoring points in a forward multi-wing centrifugal fan. The numerical results show that abnormal eddies mainly appear at the volute outlet and near the volute tongue, boundary layer separation occurs near the suction surface of the blade, and shedding eddies appear at the trailing edge of the blade with the time evolution. The unsteady flow characteristics of a forward multi-wing centrifugal fan at a small flow rate provide significant physical insight into understanding the internal flow law.

scholarly journals Unsteady Flow Characteristics of Rotating Stall and Surging in a Backward Centrifugal Fan at Low Flow-Rate Conditions

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 872 ◽  
Author(s):  
Biao Zhou ◽  
Ximing He ◽  
Hui Yang ◽  
Zuchao Zhu ◽  
Yikun Wei ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Flow Rate ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Rotating Stall ◽  
Low Flow ◽  
Small Scale ◽  
Centrifugal Fan ◽  
Unsteady Characteristics ◽  
Low Flow Rate

The steady and unsteady flow characteristics of internal flow in a backward centrifugal fan of double inlet at low flow-rate condition are investigated by computational fluid dynamics in this paper. The investigation aims to reveal insights into generation mechanisms and our physical understanding of the rotating stall and surge. The numerical results mainly demonstrate that, with decreasing flow rate, a large number of vortex flows almost increasingly occupy the internal flow of the impeller. The reverse flow and separation vortices increasingly appear near the outlet of volute, and the internal flow of the impeller is completely blocked by the separated vortex flow at low flow-rate conditions. Results indicate that, due to a synchronization of the impeller rotation and separation vortex, these separated vortices act intensely on the pressure surface of the blade with time evolution, and the interaction between the separated vortices and surface of blade increasingly yields small-scale eddies. It is further found that the amplitude of pressure and velocity fluctuations gradually increase with the decrease of flow rate in a certain range. The unsteady characteristics acting on the volute tongue gradually increase in a range of Qd to 0.3 Qd (Qd is the design volume flow rate) with the decrease of flow rate, and the unsteady characteristics acting on the volute tongue are weakened at the working condition of 0.15 Qd. These insights clearly explain the unsteady nature of the rotating stall and surge phenomenon in the double inlet backward centrifugal fan.

Flow in the Simplified Draft Tube of a Francis Turbine Operating at Partial Load—Part II: Control of the Vortex Rope

2014 ◽  
Vol 81 (6) ◽  
Author(s):  
Hosein Foroutan ◽  
Savas Yavuzkurt
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Pressure Fluctuations ◽  
Companion Paper ◽  
Francis Turbine ◽  
Control Technique ◽  
Outer Flow ◽  
Vortex Rope ◽  
Stagnant Region ◽  
Partial Load

Numerical simulations and investigation of a method for controlling the vortex rope formation in draft tubes are carried out in this paper, which is the second part of a two-paper series. As shown in the companion paper, formation of the vortex rope is associated with a large stagnant region at the center of the draft tube. Therefore, it is concluded that a successful control technique should focus on the elimination of this region. In practice, this can be performed by axially injecting a small fraction (a few percent of the total flow rate) of water into the draft tube. Water jet is supplied from the high-pressure flow upstream of the turbine spiral case by a bypass line; thus, no extra pump is needed in this method. It is shown that this method is very effective in elimination of the stagnant region in a simplified draft tube operating at two part-load conditions, i.e., at 91% and 70% of the best efficiency point (BEP) flow rate. This results in improvement of the draft tube performance and reduction of hydraulic losses. The loss coefficient is reduced by as much as 50% for the case with 91% of BEP flow rate and 14% for the case with 70% of BEP flow rate. Unsteady, three-dimensional simulations show that the jet increases the axial momentum of flow at the center of the draft tube and decreases the wake of the crown cone and thereby decreases the shear at the interface of the stagnant region and high velocity outer flow, which ultimately results in elimination of the vortex rope. Furthermore, reduction (by about 1/3 in the case with 70% of BEP flow rate) of strong pressure fluctuations leads to reliable operation of the turbine.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

scholarly journals Inter-Blade Vortex and Vortex Rope Characteristics of a Pump-Turbine in Turbine Mode under Low Flow Rate Conditions

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2554 ◽  
Author(s):  
Seung-Jun Kim ◽  
Jun-Won Suh ◽  
Young-Seok Choi ◽  
Jungwan Park ◽  
No-Hyun Park ◽  
...  
Keyword(s):  
Flow Rate ◽  
Stokes Equations ◽  
Low Flow ◽  
Renewable Energy Resources ◽  
Two Phase ◽  
Constant Frequency ◽  
Pump Turbine ◽  
Vortex Rope ◽  
Turbine Mode ◽  
Low Flow Rate

Pump-turbines are often used to provide a stable power supply with a constant frequency in response to intermittent renewable energy resources. However, existing pumped-storage power stations often operate under off-design conditions because of the increasing amounts of inconsistent renewable resources that have been added to the grid. Under off-design low flow rate conditions, inter-blade vortex and vortex rope phenomena usually develop in the runner and draft tube passages, respectively, in turbine mode. These vortices cause complicated flow patterns and pressure fluctuations that destabilize the operation of the pump-turbine system. Therefore, this study investigates the influence of correlation between the inter-blade vortex and vortex rope phenomena under low flow rate conditions. Three-dimensional steady- and unsteady-state Reynolds-averaged Navier–Stokes equations were calculated with a two-phase flow analysis using a shear stress transport as the turbulence model. The inter-blade vortices in the runner passages were captured well at the low flow rate conditions, and the vortex rope was found to develop within a specific range of low flow rates. These vortex regions showed a blockage effect and complicated flow characteristics with backflow in the passages. Moreover, higher unsteady pressure characteristics occurred at locations where the vortices were especially pronounced.

304 3-D Simulation of internal flow in Screw-Type Centrifugal Pump at Low Flow Rate

2000 ◽  
Vol 005.2 (0) ◽  
pp. 75-76
Author(s):  
Yasushi TATEBAYASHI ◽  
Kazuhiro TANAKA ◽  
Masamichi IINO
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Internal Flow ◽  
Low Flow ◽  
Low Flow Rate

Computational Study of Pump Turbine: Partial Load Operations

2020 ◽  
Author(s):  
Muhannad Altimemy ◽  
Justin Caspar ◽  
Alparslan Oztekin
Keyword(s):  
Flow Rate ◽  
Draft Tube ◽  
Computational Study ◽  
Pressure Fluctuations ◽  
System Stability ◽  
Pump Turbine ◽  
Vortex Rope ◽  
Signal Velocity ◽  
Partial Load ◽  
Les Model

Abstract The performance of a pump-turbine under partial flow rates, 85%, 75%, and 65%, is studied using the LES model. The power signal, velocity, vorticity, and pressure field is presented over the blades and throughout the draft tube. Pressure fluctuations are probed at various locations over the wall of the draft tube. Examining the flow field in the blade region can provide further insights into the system performance. Flow-induced pressure fluctuations can disrupt system stability. For this turbine, a strong swirling region is observed around the draft tube walls, causing pressure fluctuations. The size and intensity of this region decrease with the flow rate. A vortex rope is present in all cases. At the design point, the strength is constant throughout the draft tube. However, at partial load, the rope is weakened along the draft tube. Between the region dominated by the vortex rope and the wall, there is a swirling shear layer, which moves closer to the wall as the flow rate decreases. Both the magnitude of pressure fluctuations at the wall and the pressure difference over the blade decrease with the flow rate. The decreased pressure differences over the blade represent less power produced, and the decline in fluctuation magnitude at the wall represents more system stability. For this turbine, there appears to be a trade-off between power and strength of pressure fluctuations.

Sign in / Sign up

Export Citation Format

Share Document