scholarly journals Improvement of Fusel Oil Features and Effect of Its Use in Different Compression Ratios for an SI Engine on Performance and Emission

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1824 ◽  
Author(s):  
Süleyman Şimşek ◽  
Hasan Saygın ◽  
Bülent Özdalyan
Keyword(s):  
Compression Ratio ◽  
Engine Performance ◽  
Spark Ignition Engine ◽  
Test Results ◽  
Fuel Blend ◽  
Fusel Oil ◽  
Performance And Emission ◽  
Fuel Blends ◽  
Spark Plug ◽  
Hc Emissions

In this study, the effects of the use of improved fusel oil on engine performance and on exhaust emissions in a spark-ignition engine were investigated experimentally in consideration of the water, gum, and moisture content at high compression ratios according to TS EN 228 standards. In the study, a four-stroke, single-cylinder, air-cooled, spark plug ignition engine with an 8/1 compression ratio was used at three different compression ratios (8/1, 8.5/1, 9.12/1). Experiments were performed for six different ratios of fuel blends (F0, F10, F20, F30, F40, and F50) at a constant speed and different loads. The data obtained from the experiments were compared with the original operating parameters of the engine while using gasoline. According to the test results, the optimal engine performance was at a 9.12/1 compression ratio and with a F30 fuel blend. With the increase from an 8/1 to 9.12/1 compression ratio for the F30 fuel blend, the overall efficiency increased by 6.91%, and the specific fuel consumption decreased by 2.35%. The effect of the optimum fusel blend on the emissions was also examined and CO emissions were reduced by 36.82%, HC emissions were reduced by 23.07%, and NOx emissions were reduced by 15.42%, while CO2 emissions were increased by 13.88%.

Hydroprocessed Renewable Jet Fuel Evaluation, Performance, and Emissions in a T-63 Turbine Engine

2011 ◽  
Author(s):  
Christopher D. Klingshirn ◽  
Matthew J. DeWitt ◽  
Rich Striebich ◽  
David Anneken ◽  
Linda Shafer ◽  
...  
Keyword(s):  
Air Force ◽  
Alternative Fuels ◽  
Engine Performance ◽  
Aviation Fuel ◽  
Fuel Blend ◽  
Turbine Engine ◽  
Performance And Emission ◽  
Term Operation ◽  
Fuel Blends ◽  
Aromatic Components

Due to potential beneficial environmental impacts and increased supply availability, alternative fuels derived from renewable resources are evolving on the forefront as unconventional substitutes for fossil fuel. Focus is being given to the evaluation and certification of Hydroprocessed Renewable Jet (HRJ), a fuel produced from animal fat and/or plant oils (triglycerides) by hydroprocessing, as the next potential synthetic aviation fuel. Extensive efforts have recently been performed at the Air Force Research Laboratory (AFRL) at Wright Patterson Air Force Base (WPAFB) to evaluate the potential of two HRJ fuels produced from camelina and tallow feedstocks. These have included characterization of the fuel chemical and physical fuel characteristics, and Fit-for-Purpose properties (FFP). The present effort describes general combustion performance and emission propensity of a T63-A-700 Allison turbine engine operated on the HRJs and 50/50 (by volume) HRJ/JP-8 fuel blends relative to a specification JP-8. In addition, engine and emission testing with a blend of the tallow-derived HRJ and 16% bio-derived aromatic components was completed. Fundamental engine performance characterization allows for determination of the suitability of potential synthetic fuels while quantitation of gaseous and particulate matter emissions provides an assessment of the potential environmental impact compared to current petroleum-derived fuels. In addition, an extended 150 hour endurance test was performed using a 50/50 blend of tallow-derived HRJ with JP-8 to evaluate the long-term operation of the engine with the synthetic fuel blend. This paper discusses the laboratory testing performed to characterize HRJs and results from the basic engine operability and emissions studies of the alternative fuel blends.

scholarly journals Effect of Additivized Biodiesel Blends on Diesel Engine Performance, Emission, Tribological Characteristics, and Lubricant Tribology

Energies ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3375 ◽  
Author(s):  
M. A. Mujtaba ◽  
H. H. Masjuki ◽  
M. A. Kalam ◽  
Fahad Noor ◽  
Muhammad Farooq ◽  
...  
Keyword(s):  
Research Work ◽  
Engine Performance ◽  
Fuel Blend ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
The Coefficient Of Friction ◽  
Hc Emissions ◽  
Mineral Lubricant ◽  
Maximum Increment ◽  
Ternary Fuel

This research work focuses on investigating the lubricity and analyzing the engine characteristics of diesel–biodiesel blends with fuel additives (titanium dioxide (TiO2) and dimethyl carbonate (DMC)) and their effect on the tribological properties of a mineral lubricant. A blend of palm–sesame oil was used to produce biodiesel using ultrasound-assisted transesterification. B30 (30% biodiesel + 70% diesel) fuel was selected as the base fuel. The additives used in the current study to prepare ternary fuel blends were TiO2 and DMC. B30 + TiO2 showed a significant reduction of 6.72% in the coefficient of friction (COF) compared to B30. B10 (Malaysian commercial diesel) exhibited very poor lubricity and COF among all tested fuels. Both ternary fuel blends showed a promising reduction in wear rate. All contaminated lubricant samples showed an increment in COF due to the dilution of combustible fuels. Lub + B10 (lubricant + B10) showed the highest increment of 42.29% in COF among all contaminated lubricant samples. B30 + TiO2 showed the maximum reduction (6.76%) in brake-specific fuel consumption (BSFC). B30 + DMC showed the maximum increment (8.01%) in brake thermal efficiency (BTE). B30 + DMC exhibited a considerable decline of 32.09% and 25.4% in CO and HC emissions, respectively. The B30 + TiO2 fuel blend showed better lubricity and a significant improvement in engine characteristics.

scholarly journals Enhancement in Combustion, Performance, and Emission Characteristics of a Diesel Engine Fueled with Ce-ZnO Nanoparticle Additive Added to Soybean Biodiesel Blends

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4578 ◽  
Author(s):  
Fayaz Hussain ◽  
Manzoore Elahi M. Soudagar ◽  
Asif Afzal ◽  
M.A. Mujtaba ◽  
I.M. Rizwanul Fattah ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Engine Performance ◽  
Emission Characteristics ◽  
Zno Nanoparticle ◽  
Oxides Of Nitrogen ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Fuel Blends ◽  
Soybean Biodiesel

This study considered the impacts of diesel–soybean biodiesel blends mixed with 3% cerium coated zinc oxide (Ce-ZnO) nanoparticles on the performance, emission, and combustion characteristics of a single cylinder diesel engine. The fuel blends were prepared using 25% soybean biodiesel in diesel (SBME25). Ce-ZnO nanoparticle additives were blended with SBME25 at 25, 50, and 75 ppm using the ultrasonication process with a surfactant (Span 80) at 2 vol.% to enhance the stability of the blend. A variable compression ratio engine operated at a 19.5:1 compression ratio (CR) using these blends resulted in an improvement in overall engine characteristics. With 50 ppm Ce-ZnO nanoparticle additive in SBME25 (SBME25Ce-ZnO50), the brake thermal efficiency (BTE) and heat release rate (HRR) increased by 20.66% and 18.1%, respectively; brake specific fuel consumption (BSFC) by 21.81%; and the CO, smoke, and hydrocarbon (HC) decreased by 30%, 18.7%, and 21.5%, respectively, compared to SBME25 fuel operation. However, the oxides of nitrogen slightly rose for all the nanoparticle added blends. As such, 50 ppm of Ce-ZnO nanoparticle in the blend is a potent choice for the enhancement of engine performance, combustion, and emission characteristics.

Engine Performance with Diesel-Biodiesel Blends Fuel and Emission Characteristics

2020 ◽  
Vol 38 (5A) ◽  
pp. 779-788
Author(s):  
Marwa N. Kareem ◽  
Adel M. Salih
Keyword(s):  
Sulfur Content ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Esterification Reaction ◽  
Biodiesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
Hc Emissions

In this study, the sunflowers oil was utilized as for producing biodiesel via a chemical operation, which is called trans-esterification reaction. Iraqi diesel fuel suffers from high sulfur content, which makes it one of the worst fuels in the world. This study is an attempt to improve the fuel specifications by reducing the sulfur content of the addition of biodiesel fuel to diesel where this fuel is free of sulfur and has a thermal energy that approaches to diesel.20%, 30% and 50% of Biodiesel fuel were added to the conventional diesel. Performance tests and pollutants of a four-stroke single-cylinder diesel engine were performed. The results indicated that the brake thermal efficiency a decreased by (4%, 16%, and 22%) for the B20, B30 and B50, respectively. The increase in specific fuel consumption was (60%, 33%, and 11%) for the B50, B30, and B20 fuels, respectively for the used fuel blends compared to neat diesel fuel. The engine exhaust gas emissions measures manifested a decreased of CO and HC were CO decreased by (13%), (39%) and (52%), and the HC emissions were lower by (6.3%), (32%), and (46%) for B20, B30 and B50 respectively, compared to diesel fuel. The reduction of exhaust gas temperature was (7%), (14%), and (32%) for B20, B30 and B50 respectively. The NOx emission increased with the increase in biodiesel blends ratio. For B50, the raise was (29.5%) in comparison with diesel fuel while for B30 and B20, the raise in the emissions of NOx was (18%) and...

scholarly journals Investigation on Physicochemical Properties of Wastewater Grown Microalgae Methyl Ester and its Effects on CI Engine

2020 ◽  
Vol 24 (1) ◽  
pp. 72-87 ◽  
Author(s):  
Sara Tayari ◽  
Reza Abedi ◽  
Ali Abedi
Keyword(s):  
Methyl Ester ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Biodiesel Production ◽  
Emissions Reduction ◽  
Test Results ◽  
Main Fatty Acid ◽  
Ci Engine ◽  
Hc Emissions ◽  
A Minor

AbstractMicroalgae have been mentioned as a promising feedstock for biodiesel production. In this study, microalgae Chlorella vulgaris (MCV) was cultivated in a bioreactor with wastewater. After biodiesel production from MCV oil via transesterification reaction, chemical and physical properties of MCV methyl ester were evaluated with regular diesel and ASTM standard. Besides, engine performance and exhaust emissions of CI engine fuelled with the blends of diesel-biodiesel were measured. The GC-MS analysis showed that oleic and linoleic acids were the main fatty acid compounds in the MCV methyl ester. Engine test results revealed that the use of biodiesel had led to a major decrease in CO and HC emissions and a modest reduction in CO2 emissions, whereas there was a minor increase in NOx emissions. Furthermore, there was a slight decrease in the engine power and torque while a modest increase in brake specific fuel consumption which are acceptable due to exhaust emissions reduction. The experimental results illustrate considerable capabilities of applied MVC biodiesel as an alternative fuel in diesel engines to diminish the emissions.

Engine performance and emission characteristics of a compression ignition engine fuelled with diesel/dimethoxymethane blends

2005 ◽  
Vol 219 (7) ◽  
pp. 905-914 ◽  
Author(s):  
Y Ren ◽  
Z H Huang ◽  
D M Jiang ◽  
L X Liu ◽  
K Zeng ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Mass Fraction ◽  
Volume Fraction ◽  
Engine Performance ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Fuel Blends ◽  
Performance And Emissions ◽  
Combustion Phase

The performance and emissions of a compression ignition engine fuelled with diesel/dimethoxymethane (DMM) blends were studied. The results showed that the engine's thermal efficiency increased and the diesel equivalent brake specific fuel consumption (b.s.f.c.) decreased as the oxygen mass fraction (or DMM mass fraction) of the diesel/DMM blends increased. This change in the diesel/DMM blends was caused by an increased fraction of the premixed combustion phase, an oxygen enrichment, and an improvement in the diffusive combustion phase. A remarkable reduction in the exhaust CO and smoke can be achieved when operating on the diesel/DMM blend. Flat NO x/smoke and thermal efficiency/smoke curves are presented when operating on the diesel/DMM fuel blends, and a simultaneous reduction in both NO x and smoke can be realized at large DMM addition. Thermal efficiency and NO x give the highest value at 2 per cent oxygen mass fraction (or 5 per cent DMM volume fraction) for the combustion of diesel/DMM blends.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

scholarly journals Review of Performance and Emmissions Characteristics of Bio-Additive Fuel on SI Engine Fuelled by Biopetrol

2015 ◽  
Vol 773-774 ◽  
pp. 430-434
Author(s):  
Azizul Mokhtar ◽  
Nazrul Atan ◽  
Najib Rahman ◽  
Amir Khalid
Keyword(s):  
Fuel Economy ◽  
Fossil Fuels ◽  
Review Paper ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Spark Ignition Engine ◽  
Si Engine ◽  
New Approach ◽  
Performance And Emission ◽  
Performance And Emissions

Bio-additive is biodegradable and produces less air pollution thus significant for replacing the limited fossil fuels and reducing threats to the environment from exhaust emissions and global warming. Instead, the bio-additives can remarkably improve the fuel economy SI engine while operating on all kinds of fuel. Some of the bio-additive has the ability to reduce the total CO2 emission from internal petrol engine. This review paper focuses to determine a new approach in potential of bio-additives blends operating with bio-petrol on performance and emissions of spark ignition engine. It is shown that the variant in bio-additives blending ratio and engine operational condition are reduced engine-out emissions and increased efficiency. It seems that the bio-additives can increase the maximum cylinder combustion pressure, improve exhaust emissions and largely reduce the friction coefficient. The review concludes that the additives usage in bio-petrol is inseparable for the better engine performance and emission control and further research is needed to develop bio-petrol specific additives.

scholarly journals Performance Assessment of DI-Diesel Engine using the Blend of Sunflower Oil and Rice Bran Oil

2019 ◽  
Vol 8 (4) ◽  
pp. 4048-4052
Keyword(s):  
Diesel Engine ◽  
Sunflower Oil ◽  
Fuel Injection ◽  
Rice Bran Oil ◽  
Engine Performance ◽  
Performance And Emission ◽  
Animal Fats ◽  
Di Diesel Engine ◽  
Hc Emissions ◽  
Direct Fuel Injection

Biodiesel, a derivative of vegetable oils and animal fats, is used nowadays as an alternative renewable and sustainable fossil fuel. In this work, the investigation of manufacture, characterization, and results of biodiesel blends are carried out using two important feedstock’s, sunflower oil and ricebran oil on engines. For the collective advantageous of sunflower oil and ricebran oil, the two biodiesels are combined together and the mixture is analysed to assess the engine performance and emission characteristics. NaOH catalyzed transesterification process is used for producing the Biodiesels A 4.4 kW, four-stroke, single-cylinder and direct fuel injection diesel engine is used for measuring physic-chemical with full load and varying speed conditions and using the specifications of ASTM D6751 standard, the properties are compared. It is observed that the Biodiesel mixtures produce a low brake torque and high brake-specific fuel consumption (BSFC) in addition to the reduction of CO and HC emissions. NOx, however, is reduced considerably with the improvement of brake thermal efficiency. The Performance analysis indicates that the mixture of sunflower oil and ricebran oil improves performance and emission characterizes over sunflower oil and ricebran oil biodiesel when they are unmixed..

Sign in / Sign up

Export Citation Format

Share Document