scholarly journals Performance Analysis of an Electromagnetically Coupled Piezoelectric Energy Scavenger

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 845 ◽  
Author(s):  
Abdolreza Pasharavesh ◽  
Reza Moheimani ◽  
Hamid Dalir
Keyword(s):  
Energy Harvesting ◽  
Multiple Scales ◽  
Nonlinear Partial Differential Equations ◽  
Low Frequency ◽  
Primary Resonance ◽  
Excitation Amplitude ◽  
Load Resistance ◽  
Response Curves ◽  
Piezoelectric Energy ◽  
Resonance Frequencies

The deliberate introduction of nonlinearities is widely used as an effective technique for the bandwidth broadening of conventional linear energy harvesting devices. This approach not only results in a more uniform behavior of the output power within a wider frequency band through bending the resonance response, but also contributes to energy harvesting from low-frequency excitations by activation of superharmonic resonances. This article investigates the nonlinear dynamics of a monostable piezoelectric harvester under a self-powered electromagnetic actuation. To this end, the governing nonlinear partial differential equations of the proposed harvester are order-reduced and solved by means of the perturbation method of multiple scales. The results indicate that, according to the excitation amplitude and load resistance, different responses can be distinguished at the primary resonance. The system behavior may involve the traditional bending of response curves, Hopf bifurcations, and instability regions. Furthermore, an order-two superharmonic resonance is observed, which is activated at lower excitations in comparison to order-three conventional resonances of the Duffing-type resonator. This secondary resonance makes it possible to extract considerable amounts of power at fractions of natural frequency, which is very beneficial in micro-electro-mechanical systems (MEMS)-based harvesters with generally high resonance frequencies. The extracted power in both primary and superharmonic resonances are analytically calculated, then verified by a numerical solution where a good agreement is observed between the results.

Nonlinear Vibrations of a Beam-Spring-Mass System

1994 ◽  
Vol 116 (4) ◽  
pp. 433-439 ◽  
Author(s):  
M. Pakdemirli ◽  
A. H. Nayfeh
Keyword(s):  
Nonlinear Response ◽  
Nonlinear Vibrations ◽  
Multiple Scales ◽  
Method Of Multiple Scales ◽  
Nonlinear Partial Differential Equations ◽  
Primary Resonance ◽  
Fast Time ◽  
Lagrange Equations ◽  
Response Curves ◽  
Mass System

The nonlinear response of a simply supported beam with an attached spring-mass system to a primary resonance is investigated, taking into account the effects of beam midplane stretching and damping. The spring-mass system has also a cubic nonlinearity. The response is found by using two different perturbation approaches. In the first approach, the method of multiple scales is applied directly to the nonlinear partial differential equations and boundary conditions. In the second approach, the Lagrangian is averaged over the fast time scale, and then the equations governing the modulation of the amplitude and phase are obtained as the Euler-Lagrange equations of the averaged Lagrangian. It is shown that the frequency-response and force-response curves depend on the midplane stretching and the parameters of the spring-mass system. The relative importance of these effects depends on the parameters and location of the spring-mass system.

scholarly journals A Multi-Mode Broadband Vibration Energy Harvester Composed of Symmetrically Distributed U-Shaped Cantilever Beams

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 203
Author(s):  
Xiaohua Huang ◽  
Cheng Zhang ◽  
Keren Dai
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Experimental Results ◽  
Vibration Energy ◽  
Cantilever Beams ◽  
Resonant Frequencies ◽  
Promising Alternative ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Resonance Frequencies

Using the piezoelectric effect to harvest energy from surrounding vibrations is a promising alternative solution for powering small electronic devices such as wireless sensors and portable devices. A conventional piezoelectric energy harvester (PEH) can only efficiently collect energy within a small range around the resonance frequency. To realize broadband vibration energy harvesting, the idea of multiple-degrees-of-freedom (DOF) PEH to realize multiple resonant frequencies within a certain range has been recently proposed and some preliminary research has validated its feasibility. Therefore, this paper proposed a multi-DOF wideband PEH based on the frequency interval shortening mechanism to realize five resonance frequencies close enough to each other. The PEH consists of five tip masses, two U-shaped cantilever beams and a straight beam, and tuning of the resonance frequencies is realized by specific parameter design. The electrical characteristics of the PEH are analyzed by simulation and experiment, validating that the PEH can effectively expand the operating bandwidth and collect vibration energy in the low frequency. Experimental results show that the PEH has five low-frequency resonant frequencies, which are 13, 15, 18, 21 and 24 Hz; under the action of 0.5 g acceleration, the maximum output power is 52.2, 49.4, 61.3, 39.2 and 32.1 μW, respectively. In view of the difference between the simulation and the experimental results, this paper conducted an error analysis and revealed that the material parameters and parasitic capacitance are important factors that affect the simulation results. Based on the analysis, the simulation is improved for better agreement with experiments.

Modeling and Experimental Validations of a Piezoelectric Energy Harvester Under Combined Galloping and Base Excitations

2014 ◽  
Author(s):  
Amin Bibo ◽  
Abdessattar Abdelkefi ◽  
Mohammed F. Daqaq
Keyword(s):  
Bluff Body ◽  
Energy Harvester ◽  
Constitutive Relations ◽  
Excitation Frequency ◽  
Primary Resonance ◽  
Beam Theory ◽  
Excitation Amplitude ◽  
The Body ◽  
Base Excitation ◽  
Piezoelectric Energy

This paper develops an experimentally validated model of a piezoelectric energy harvester under combined aeroelastic-galloping and base excitations. To that end, an energy harvester consisting of a thin piezoelectric cantilever beam subjected to vibratory base excitation is considered. To permit galloping excitation, a bluff body is rigidly attached at the free end such that a net aerodynamic lift is generated as the incoming airflow separates on both sides of the body giving rise to limit cycle oscillations when the flow velocity exceeds a critical value. A nonlinear electromechanical distributed-parameter model of the harvester under the combined excitation is derived using the energy approach and by adopting the nonlinear Euler-Bernoulli beam theory, linear constitutive relations for the piezoelectric transduction, and the quasi-steady assumption for the aerodynamic loading. The partial differential equations of the system are discretized and a reduced-order-model is obtained. The mathematical model is validated by conducting a series of experiments with different loading conditions represented by wind speed, base excitation amplitude, and excitation frequency around the primary resonance.

scholarly journals Modeling of Piezoelectric Energy Harvesting from Freely Oscillating Cylinders in Water Flow

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Min Zhang ◽  
YingZheng Liu ◽  
ZhaoMin Cao
Keyword(s):  
Energy Harvesting ◽  
Free Stream ◽  
Piezoelectric Materials ◽  
Load Resistance ◽  
Stream Velocity ◽  
Piezoelectric Energy Harvesting ◽  
Vibratory System ◽  
System Parameters ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations

A concept of energy harvesting from vortex-induced vibrations of a rigid circular cylinder with two piezoelectric beams attached is investigated. The variations of the power levels with the free stream velocity are determined. A mathematical approach including the coupled cylinder motion and harvested voltage is presented. The effects of the load resistance, piezoelectric materials, and circuit combined on the natural frequency and damping of the vibratory system are determined by performing a linear analysis. The dynamic response of the cylinder and harvested energy are investigated. The results show that the harvested level in SS and SP&PS modes is the same with different values of load resistance. For four different system parameters, the results show that the bigger size of cylinder with PZT beams can obtain the higher harvested power.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals Piezoelectric Energy Harvesting with an Ultrasonic Vibration Source

Actuators ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 8
Author(s):  
Tao Li ◽  
Pooi Lee
Keyword(s):  
Energy Harvesting ◽  
High Power ◽  
High Frequency ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Low Frequency ◽  
Vibration Source ◽  
Piezoelectric Energy ◽  
Power Ultrasonic ◽  
Ultrasonic Cutting

A piezoelectric energy harvester was developed in this paper. It is actuated by the vibration leakage from the nodal position of a high-power ultrasonic cutting transducer. The harvester was excited at a low displacement amplitude (0.73 µmpp). However, its operation frequency is quite high and reaches the ultrasonic range (24.4 kHz). Compared with another low frequency harvester (66 Hz), both theoretical and experimental results proved that the advantages of this high frequency harvester include (i) high current generation capability (up to 20 mApp compared to 1.3 mApp of the 66 Hz transducer) and (ii) low impedance matching resistance (500 Ω in contrast to 50 kΩ of the 66 Hz transducer). This energy harvester can be applied either in sensing, or vibration controlling, or simply energy harvesting in a high-power ultrasonic system.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

scholarly journals Experimental Study on Piezoelectric Energy Harvesting from Vortex-Induced Vibrations and Wake-Induced Vibrations

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Min Zhang ◽  
Junlei Wang
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Maximum Output Power ◽  
Load Resistance ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations ◽  
Flow Induced Vibrations ◽  
Generation Capacity ◽  
Output Characteristics

A rigid circular cylinder with two piezoelectric beams attached on has been tested through vortex-induced vibrations (VIV) and wake-induced vibrations (WIV) by installing a big cylinder fixed upstream, in order to study the influence of the different flow-induced vibrations (FIV) types. The VIV test shows that the output voltage increases with the increases of load resistance; an optimal load resistance exists for the maximum output power. The WIV test shows that the vibration of the small cylinder is controlled by the vortex frequency of the large one. There is an optimal gap of the cylinders that can obtain the maximum output voltage and power. For a same energy harvesting device, WIV has higher power generation capacity; then the piezoelectric output characteristics can be effectively improved.

Development of a tunable low-frequency vibration energy harvester and its application to a self-contained wireless fatigue crack detection sensor

2018 ◽  
Vol 18 (3) ◽  
pp. 920-933 ◽  
Author(s):  
Suyoung Yang ◽  
Sung-Youb Jung ◽  
Kiyoung Kim ◽  
Peipei Liu ◽  
Sangmin Lee ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Energy Harvesting ◽  
Crack Detection ◽  
Energy Harvester ◽  
Low Frequency ◽  
Vibration Energy ◽  
Low Frequency Vibration ◽  
Resonance Frequencies ◽  
Energy Harvesting System ◽  
Fatigue Crack Detection

In this study, a tunable electromagnetic energy harvesting system, consisting of an energy harvester and energy harvesting circuits, is developed for harnessing energy from low-frequency vibration (below 10 Hz) of a bridge, and the harvesting system is integrated with a wireless fatigue crack detection sensor. The uniqueness of the proposed energy harvesting system includes that (1) the resonance frequencies of the proposed energy harvester can be readily tuned to the resonance frequencies of a host structure, (2) an improved energy harvesting efficiency compared to other electromagnetic energy harvesters is achieved in low-frequency and vibration, and (3) high-efficiency energy harvesting circuits for rectification are developed. Furthermore, the developed energy harvesting system is integrated with an on-site wireless sensor deployed on Yeongjong Grand Bridge in South Korea for online fatigue crack detection. To the best knowledge of the authors, this is the very first study where a series of low-frequency vibration energy harvesting, rectification, and battery charging processes are demonstrated under a real field condition. The field test conducted on Yeongjong Grand Bridge, where fatigue cracks have become of a great concern, shows that the proposed energy harvester can generate a peak voltage of 2.27 V and a root mean square voltage of 0.21 V from 0.18-m/s2 root mean square acceleration at 3.05 Hz. It is estimated the proposed energy harvesting system can harness around 67.90 J for 3 weeks and an average power of 37.42 µW. The battery life of the wireless sensor is expected to extend from 1.5 to 2.2 years. The proposed energy harvesting circuits, composed of the AC–DC and boost-up converters, exhibit up to 50% battery charging efficiency when the voltage generated by the proposed energy harvester is 200 mV or higher. The proposed boost-up converter has a 100 times wider input power range than a conventional boost-up converter with a similar efficiency.

Nonlinear Vibrations of a Beam-Spring-Large Mass System

2017 ◽  
Author(s):  
Mohammad A. Bukhari ◽  
Oumar R. Barry
Keyword(s):  
Natural Frequencies ◽  
Multiple Scales ◽  
Equations Of Motion ◽  
Primary Resonance ◽  
Large Mass ◽  
Mode Shapes ◽  
Resonance Excitation ◽  
Response Curves ◽  
Mass System ◽  
Spring System

This paper presents the nonlinear vibration of a simply supported Euler-Bernoulli beam with a mass-spring system subjected to a primary resonance excitation. The nonlinearity is due to the mid-plane stretching and cubic spring stiffness. The equations of motion and the boundary conditions are derived using Hamiltons principle. The nonlinear system of equations are solved using the method of multiple scales. Explicit expressions are obtained for the mode shapes, natural frequencies, nonlinear frequencies, and frequency response curves. The validity of the results is demonstrated via comparison with results in the literature. Exact natural frequencies are obtained for different locations, rotational inertias, and masses.

Sign in / Sign up

Export Citation Format

Share Document