scholarly journals Experimental Study on Piezoelectric Energy Harvesting from Vortex-Induced Vibrations and Wake-Induced Vibrations

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Min Zhang ◽  
Junlei Wang
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Maximum Output Power ◽  
Load Resistance ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations ◽  
Flow Induced Vibrations ◽  
Generation Capacity ◽  
Output Characteristics

A rigid circular cylinder with two piezoelectric beams attached on has been tested through vortex-induced vibrations (VIV) and wake-induced vibrations (WIV) by installing a big cylinder fixed upstream, in order to study the influence of the different flow-induced vibrations (FIV) types. The VIV test shows that the output voltage increases with the increases of load resistance; an optimal load resistance exists for the maximum output power. The WIV test shows that the vibration of the small cylinder is controlled by the vortex frequency of the large one. There is an optimal gap of the cylinders that can obtain the maximum output voltage and power. For a same energy harvesting device, WIV has higher power generation capacity; then the piezoelectric output characteristics can be effectively improved.

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals Modeling of Piezoelectric Energy Harvesting from Freely Oscillating Cylinders in Water Flow

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Min Zhang ◽  
YingZheng Liu ◽  
ZhaoMin Cao
Keyword(s):  
Energy Harvesting ◽  
Free Stream ◽  
Piezoelectric Materials ◽  
Load Resistance ◽  
Stream Velocity ◽  
Piezoelectric Energy Harvesting ◽  
Vibratory System ◽  
System Parameters ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations

A concept of energy harvesting from vortex-induced vibrations of a rigid circular cylinder with two piezoelectric beams attached is investigated. The variations of the power levels with the free stream velocity are determined. A mathematical approach including the coupled cylinder motion and harvested voltage is presented. The effects of the load resistance, piezoelectric materials, and circuit combined on the natural frequency and damping of the vibratory system are determined by performing a linear analysis. The dynamic response of the cylinder and harvested energy are investigated. The results show that the harvested level in SS and SP&PS modes is the same with different values of load resistance. For four different system parameters, the results show that the bigger size of cylinder with PZT beams can obtain the higher harvested power.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

scholarly journals Performance Evaluation of a Piezoelectric Energy Harvester Based on Flag-Flutter

Micromachines ◽  
2020 ◽  
Vol 11 (10) ◽  
pp. 933 ◽  
Author(s):  
Hassan Elahi ◽  
Marco Eugeni ◽  
Federico Fune ◽  
Luca Lampani ◽  
Franco Mastroddi ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Wind Tunnel ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Research Work ◽  
Maximum Output ◽  
Operational Environment ◽  
Subsonic Wind Tunnel ◽  
Piezoelectric Energy

In the last few decades, piezoelectric (PZT) materials have played a vital role in the aerospace industry because of their energy harvesting capability. PZT energy harvesters (PEH) absorb the energy from an operational environment and can transform it into useful energy to drive nano/micro-electronic components. In this research work, a PEH based on the flag-flutter mechanism is presented. This mechanism is based on fluid-structure interaction (FSI). The flag is subjected to the axial airflow in the subsonic wind tunnel. The performance evaluation of the harvester and aeroelastic analysis is investigated numerically and experimentally. A novel solution is presented to extract energy from Limit Cycle Oscillations (LCOs) phenomenon by means of PZT transduction. The PZT patch absorbs the flow-induced structural vibrations and transforms it into electrical energy. Furthermore, the optimal resistance and length of the flag is predicted to maximize the energy harvesting. Different configurations of flag i.e., with Aluminium (Al) patch and PZT patch for flutter mode vibration mode are studied numerically and experimentally. The bifurcation diagram is constructed for the experimental campaign for the flutter instability of a cantilevered flag in subsonic wind-tunnel. Moreover, the flutter boundary conditions are analysed for reduced critical velocity and frequency. The designed PZT energy harvester via flag-flutter mechanism is suitable for energy harvesting in aerospace engineering applications to drive wireless sensors. The maximum output power that can be generated from the designed harvester is 6.72 mW and the optimal resistance is predicted to be 0.33 MΩ.

scholarly journals Improved Multilayered (Bi,Sc)O3-(Pb,Ti)O3 Piezoelectric Energy Harvesters Based on Impedance Matching Technique

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 1958 ◽  
Author(s):  
Bo Su Kim ◽  
Jae-Hoon Ji ◽  
Hong-Tae Kim ◽  
Sung-Jin Kim ◽  
Jung-Hyuk Koh
Keyword(s):  
Energy Harvesting ◽  
Impedance Matching ◽  
Load Resistance ◽  
Mechanical Force ◽  
Output Energy ◽  
Maximum Output ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Matching Technique ◽  
Matching Techniques

As a piezoelectric material, (Bi,Sc)O3-(Pb,Ti)O3 ceramics have been tested and analyzed for sensors and energy harvester applications owing to their relatively high Curie temperature and high piezoelectric coefficient. In this work, we prepared optimized (Bi,Sc)O3-(Pb,Ti)O3 piezoelectric materials through the conventional ceramic process. To increase the output energy, a multilayered structure was proposed and designed, and to obtain the maximum output energy, impedance matching techniques were considered and tested. By varying and measuring the energy harvesting system, we confirmed that the output energies were optimized by varying the load resistance. As the load resistance increased, the output voltage became saturated. Then, we calculated the optimized output power using the electric energy formula. Consequently, we identified the highest output energy of 5.93 µW/cm2 at 3 MΩ for the quadruple-layer harvester and load resistor using the impedance matching system. We characterized and improved the electrical properties of the piezoelectric energy harvesters by introducing impedance matching and performing the modeling of the energy harvesting component. Modeling was conducted for the piezoelectric generator component by introducing the mechanical force dependent voltage sources and load resistors and piezoelectric capacitor connected in parallel. Moreover, the generated output voltages were simulated by introducing an impedance matching technique. This work is designed to explain the modeling of piezoelectric energy harvesters. In this model, the relationship between applied mechanical force and output energy was discussed by employing experimental results and simulation.

Impact-driven piezoelectric energy harvester using a pendulum structure for low-frequency vibration

2021 ◽  
pp. 1045389X2098388
Author(s):  
Guifen Fan ◽  
Yanjiong Wang ◽  
Feng Tian ◽  
Mengmeng Hao ◽  
Yue Wen ◽  
...  
Keyword(s):  
Maximum Output Power ◽  
Low Frequency ◽  
Load Resistance ◽  
Open Circuit ◽  
Maximum Output ◽  
Peak Voltage ◽  
Ball Impact ◽  
Piezoelectric Energy ◽  
Low Frequency Vibration ◽  
Piezoelectric Cantilevers

This study investigates a pendulum ball impact-excited piezoelectric energy harvester (PEH) for low frequency vibration through finite element analysis and experimental verification. This structure can harvest the vibration energy of infrasonic level, which provides a new idea for the energy harvest of low frequency. Experimental results show that for a pendulum ball impact-excited PEH with a 2.5 mm horizontal displacement excitation at 2 Hz, namely the sinusoidal excitation acceleration of 0.04 g, the collision frequency between the pendulum and the cantilevers reaches 10 Hz, and the open-circuit peak voltage of two piezoelectric cantilevers in the collision is 30.1 and 27.1 V respectively. Under the parallel connection of two piezoelectric cantilevers, the open-circuit peak voltage is 15.8 V and a maximum output power of 10.53 μW can be achieved across a 130 kΩ external load resistance. Compared with a single pendulum ball structure, a bi-pendulum ball structure can interact with two cantilever beams in one collision, thereby improving the efficiency of energy collection and reducing the optimal load resistance. A maximum output power of 43 μW can be achieved across a 47 kΩ external load resistance and 2 Hz rotational vibration excitation.

Modeling of Piezoelectric Acoustic Energy Harvester

2014 ◽  
Vol 695 ◽  
pp. 757-760 ◽  
Author(s):  
Susilo Sidik ◽  
Azma Putra ◽  
Swee Leong Kok
Keyword(s):  
Energy Harvesting ◽  
Acoustic Waves ◽  
Piezoelectric Materials ◽  
Maximum Output Power ◽  
Flexural Vibration ◽  
Electrical Energy ◽  
Load Resistance ◽  
Acoustic Energy ◽  
Maximum Output ◽  
Energy Harvesters

Harvesting ambient acoustics for conversion into usable electricity provides a potential power source for emerging technologies including wireless sensor networks. Acoustic energy harvesters convert energy from acoustic waves to electrical energy. Here acoustic energy harvesting from ambient noise utilizing flexural vibration of a flexible panel is investigated. A flexural vibration from the panel is use to extract more energy from the ambient acoustics where piezoelectric materials of PVDF films are attached around the plate edges. This study found that the energy harvesting can be obtained with a maximum output power of 480 pW at 400 kΩ load resistance.

scholarly journals Numerical analysis of semiconductor thermoelectric generator

2020 ◽  
Vol 24 (3 Part A) ◽  
pp. 1585-1591
Author(s):  
Zhifei Wu ◽  
Yuxia Xiang ◽  
Jianjun Wang
Keyword(s):  
Contact Resistance ◽  
Output Power ◽  
Temperature Difference ◽  
Output Voltage ◽  
Thermoelectric Generator ◽  
Maximum Output Power ◽  
Load Resistance ◽  
Maximum Output ◽  
Generation Model ◽  
Output Performance

A thermoelectric generation model is proposed based on the structure of thermoelectric generator, working conditions, the effect of air heat transfer and contact resistance in thermoelectric components. In addition, the effect of the thermoelectric generator output performance under the condition of different temperature of the cold and heat source, contact resistance between the cold-end and hot-end, the load resistance and the contact resistance is calculated. The results show that the output voltage is linear associate with the temperature difference between hot and cold ends, however, the output power increase along with the increase of temperature of hot-end and decrease of cold-end. The output voltage reaches 5.76 V and the output power reaches 9.81 W when the temperature difference is 200?C. Assume that the contact resistance is ignored, the output voltage and power reach peak values of 3.61 V and 3.85 W. The output performance of thermoelectric generator decreases with the increase of thermal contact resistance at hot and cold ends, and the reduction is getting lower and lower. With the increase of the load resistance, the output power increases at the beginning and then decreases. The optimal output power is 3.69 W when the contact resistance is 0 ? and the optimal load resistance is 3.3 ?. The maximum output power corresponding to neglecting the contact resistance will be reduced by 13.5% when the contact resistance is 0.5 ?.

Sign in / Sign up

Export Citation Format

Share Document