scholarly journals Analysis and Implementation of a Phase-Shift Pulse-Width Modulation Converter with Auxiliary Winding Turns

Energies ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 222
Author(s):  
Bor-Ren Lin
Keyword(s):  
Phase Shift ◽  
Pulse Width ◽  
Pulse Width Modulation ◽  
Input Voltage ◽  
Power Converter ◽  
Railway Vehicle ◽  
Voltage Range ◽  
Voltage Variation ◽  
Power Switches ◽  
Output Side

A phase-shift pulse-width modulation converter is studied and investigated for railway vehicle or solar cell power converter applications with wide voltage operation. For railway vehicle applications, input voltage range of dc converters is requested to have 30–40% voltage variation of the nominal input voltage. The nominal input voltages of dc converters on railway vehicles applications may be 37.5 V, 48 V, 72 V, 96 V and 110 V. Therefore, a new dc converter with wide input voltage operation from 25 to 150 V is presented to withstand different nominal input voltage levels such as 37.5–110 V on railway power units. To realize wide input voltage operation, an auxiliary switch and auxiliary transformer windings are used on output side of conventional full-bridge converter to have different voltage gains under different input voltage values. Phase-shift pulse-width modulation is adopted in the developed dc converter to accomplish soft switching operation on power switches. To confirm and validate the practicability of the presented converter, experiments based on a 300 W prototype were provided in this paper.

scholarly journals Phase-Shift PWM Converter with Wide Voltage Operation Capability

Electronics ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 47 ◽  
Author(s):  
Bor-Ren Lin
Keyword(s):  
Phase Shift ◽  
Pulse Width Modulation ◽  
Design Procedure ◽  
Input Voltage ◽  
Pwm Converter ◽  
Voltage Range ◽  
Active Devices ◽  
Power Switches ◽  
Input Side ◽  
Zero Voltage

A soft switching three-level pulse-width modulation (PWM) converter is presented for industrial electronics with wide voltage range operation, such as solar power or fuel cell applications. Phase shift PWM scheme is used on the input-side to accomplish the zero voltage turn-on on power switches and improve the converter efficiency. Three-level diode-clamp circuit topology is adopted in the presented circuit to lessen the voltage ratings on active devices for high voltage applications. Three sub-circuits with the different turns-ratio of transformers can be selected in the presented converter in order to achieve 10:1 (Vin,max = 10Vin,min) wide input voltage operation when compared to the conventional multilevel converter. The proposed circuit is a single-stage converter instead of two-stage converter to realize wide voltage operation. Therefore, the presented converter has less component counts. Finally, the design procedure and experiments with a 300W laboratory circuit are presented and discussed to confirm the circuit analysis and converter performance.

scholarly journals Hybrid DC-DC Converter with Low Switching Loss, Low Primary Current and Wide Voltage Operation

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2536
Author(s):  
Bor-Ren Lin ◽  
Yi-Kuan Lin
Keyword(s):  
Pulse Width ◽  
Pulse Width Modulation ◽  
Input Voltage ◽  
Resonant Circuit ◽  
Switching Loss ◽  
Voltage Range ◽  
Current Loss ◽  
Zero Voltage Switching ◽  
Energy Applications ◽  
Multi Stage

A full-bridge converter with an additional resonant circuit and variable secondary turns is presented and achieved to have soft-switching operation on active devices, wide voltage input operation and low freewheeling current loss. The resonant tank is linked to the lagging-leg of the full bridge pulse-width modulation converter to realize zero-voltage switching (ZVS) characteristic on the power switches. Therefore, the wide ZVS operation can be accomplished in the presented circuit over the whole input voltage range and output load. To overcome the wide voltage variation on renewable energy applications such as DC wind power and solar power conversion, two winding sets are used on the output-side of the proposed converter to obtain the different voltage gains. Therefore, the wide voltage input from 90 to 450 V (Vin,max = 5Vin,min) is implemented in the presented circuit. To further improve the freewheeling current loss issue in the conventional phase-shift pulse-width modulation converter, an auxiliary DC voltage generated from the resonant circuit is adopted to reduce this freewheeling current loss. Compared to the multi-stage DC converters with wide input voltage range operation, the proposed circuit has a low freewheeling current loss, low switching loss and a simple control algorithm. The studied circuit is tested and the experimental results are demonstrated to testify the performance of the resented circuit.

scholarly journals Analysis of a PWM Converter with Less Current Ripple, Wide Voltage Operation and Zero-Voltage Switching

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 580
Author(s):  
Bor-Ren Lin ◽  
Yi-Hao Peng
Keyword(s):  
Integrated Circuit ◽  
Pulse Width Modulation ◽  
Input Voltage ◽  
Power Converter ◽  
Switching Loss ◽  
Voltage Range ◽  
Zero Voltage Switching ◽  
General Phase ◽  
Zero Voltage ◽  
Current Ripple

This paper studies and implements a power converter to have less current ripple output and wide voltage input operation. A three-leg converter with different primary turns is presented on its high-voltage side to extend the input voltage range. The current doubler rectification circuit is adopted on the output side to have low current ripple capability. From the switching states of the three-leg converter, the presented circuit has two equivalent sub-circuits under different input voltage ranges (Vin = 120–270 V or 270–600 V). The general phase-shift pulse-width modulation is employed to control the presented converter so that power devices can be turned on at zero voltage in order to reduce switching loss. Compared to two-stage circuit topologies with a wide voltage input operation, the presented converter has the benefits of simple circuit structure, easy control algorithm using a general integrated circuit or digital controller, and less components. The performance of the presented circuit is confirmed and validated by an 800 W laboratory prototype.

scholarly journals ZVS Full–Bridge Based DC–DC Converter with Linear Voltage Gain According to Duty Cycle

2013 ◽  
Vol 64 (5) ◽  
pp. 331-333
Author(s):  
Hyun-Lark Do
Keyword(s):  
Duty Cycle ◽  
Pulse Width Modulation ◽  
High Efficiency ◽  
Input Voltage ◽  
Voltage Gain ◽  
Voltage Range ◽  
Zero Voltage Switching ◽  
Switching Losses ◽  
Power Switches ◽  
Linear Voltage

Abstract This paper presents a zero-voltage-switching (ZVS) full-bridge based DC-DC converter with linear voltage gain according to duty cycle. The proposed converter is based on an asymmetrical pulse-width-modulation (APWM) full-bridge converter which has various advantages over other converters. However, it has some drawbacks such as limited maximum duty cycle to 0.5 and narrow input range. The proposed converter overcomes these problems. The duty cycle is not limited and input voltage range is wide. Also, the ZVS operation of all power switches is achieved. Therefore, switching losses are significantly reduced and high-efficiency is obtained. Steady-state analysis and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter.

scholarly journals Interleaved 4-Phases DC/DC Converter for Electric Scooter to Improve Efficiency

2018 ◽  
Vol 225 ◽  
pp. 03013
Author(s):  
Khairul Nisak Md Hasan ◽  
Aida Syafiqah Ahmad ◽  
Zainul Azhar Zakaria
Keyword(s):  
Phase Shift ◽  
Pulse Width ◽  
Pulse Width Modulation ◽  
Dc Motor ◽  
Power Converter ◽  
Boost Converter ◽  
Switching Frequency ◽  
Matlab Simulink ◽  
Improve Efficiency ◽  
Electric Scooter

This paper presents the design of an Interleaved DC/DC Boost Converter for the implementation of an Electric Scooter. The output of the power converter can be controlled using the Pulse Width Modulation (PWM) switching technique to boost 12V battery supply to power a 24V Brushed DC Motor with improved efficiency compared to conventional converters. The design of the power converter was calculated for different number of interleaving phases. The simulation is carried out using MATLAB/Simulink for 2, 3, 4, 6 and 8-phases interleaved converters to compare their performances. The 4-phase is selected due to its advantage and further implemented in the prototype. PWM output switching frequency is set to 25 kHz with 4 signals of 90° phase shift to each other. The testing on a complete prototype was carried out.

scholarly journals Bounding the Output Error in a Buck Power Converter Using Perturbation Theory

2008 ◽  
Vol 2008 ◽  
pp. 1-20 ◽  
Author(s):  
Fabiola Angulo ◽  
Enric Fossas ◽  
Tere M. Seara ◽  
Gerard Olivar
Keyword(s):  
Perturbation Theory ◽  
Pulse Width ◽  
Pulse Width Modulation ◽  
Dynamic Control ◽  
Power Converter ◽  
Control Technique ◽  
Order System ◽  
Sliding Surface ◽  
Output Error ◽  
Average Theory

We show the main results obtained when applying the average theory to Zero Average Dynamic control technique in a buck power converter with pulse-width modulation (PWM). In particular, we have obtained the bound values for output error and sliding surface. The PWM with centered and lateral pulse configurations were analyzed. The analytical results have confirmed the numerical and experimental results already obtained in previous publications. Moreover, through an important lemma, we have generalized the theory for any stable second-order system with relative degree 2, using properties related to transformations and stability of linear systems.

scholarly journals Design and Implementation of 2.5kW IBFB-LLC DC/ DC Converter Using SiC Mosfet

2021 ◽  
Vol 31.2 (149) ◽  
pp. 7-14
Keyword(s):  
High Frequency ◽  
Power Flow ◽  
Input Voltage ◽  
Voltage Range ◽  
Zero Voltage Switching ◽  
Design And Implementation ◽  
Switching Losses ◽  
Power Switches ◽  
Isolation Transformer ◽  
Zero Voltage

Interleaved Boost Full Bridge integrated LLC resonant (IBFB- LLC) is an isolated DC/DC converter with directional power flow, which can cope with a wide input voltage range of PV applications. The main losses of the converter are switching losses of the power switches and transformers losses. This paper proposes a method to improve the efficiency of the IBFB converter due to zero voltage switching technique, in combination with employing new SiC MOSFET technology instead of the conventional Si MOSFET. In addition, Litz wire is also adopted to reduce the losses on the high frequency isolation transformer. Both numerical simulations and experiments with a prototype 2.5kW converter are implemented to verify the feasibility and effectiveness of the proposed solution.

Compact CMOS Analog Multiplier Free of Voltage Reference Generators

2020 ◽  
Vol 15 (3) ◽  
pp. 1-12
Author(s):  
Ana Isabela Araújo Cunha ◽  
Antonio José Sobrinho De Sousa ◽  
Edson Pinto Santana ◽  
Robson Nunes De Lima ◽  
Fabian Souza De Andrade ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Harmonic Distortion ◽  
Current Mode ◽  
Input Voltage ◽  
Voltage Reference ◽  
Analog Multiplier ◽  
Voltage Range ◽  
Voltage Variation ◽  
Static Power ◽  
Four Quadrant

This work presents a CMOS four quadrant analog multiplier architecture for application as the synapse element in analog cellular neural networks. For this reason, the circuit has voltage-mode inputs and a current-mode output and the chief design targets are compactness and low energy consumption. A signal application method is proposed that avoids voltage reference generators, which contributes to reduce sensitivity to supply voltage variation. Performance analysis through simulation has been accomplished for a design in CMOS 130 nm technology with 163 µm2 total active area. The circuit features ±50 mV input voltage range, 86 µW static power and ‑28.4 dB maximum total harmonic distortion. A simple technique for manual calibration is also presented.

Sign in / Sign up

Export Citation Format

Share Document