scholarly journals Analysis of Convergence Characteristics of Average Method Regulated by ISO 9869-1 for Evaluating In Situ Thermal Resistance and Thermal Transmittance of Opaque Exterior Walls

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1989 ◽  
Author(s):  
Doo Sung Choi ◽  
Myeong Jin Ko
Keyword(s):  
Thermal Resistance ◽  
Average Method ◽  
Test Duration ◽  
Test Environment ◽  
Building Envelopes ◽  
Thermal Transmittance ◽  
The Third ◽  
U Value ◽  
R Value

In the last few decades, an average method which is regulated by ISO 9869-1 has been used to evaluate the in situ thermal transmittance (U-value) and thermal resistance (R-value) of building envelopes obtained from onsite measurements and to verify the validity of newly proposed methods. Nevertheless, only a few studies have investigated the test duration required to obtain reliable results using this method and the convergence characteristics of the results. This study aims to evaluate the convergence characteristics of the in situ values analyzed using the average method. The criteria for determining convergence (i.e., end of the test) using the average method are very strict, mainly because of the third condition, which compares the deviation of two values derived from the first and last periods of the same duration. To shorten the test duration, environmental variables should be kept constant throughout the test or an appropriate period should be selected. The convergence of the in situ U-value and R-value is affected more by the length of the test duration than by the temperature difference if the test environment meets literature-recommended conditions. Furthermore, there is no difference between the use of the U-value and R-value in determining the end of the test.

scholarly journals Quicker Measurement of Walls’ Thermal Resistance Following an Extension to ISO 9869 Average Method

2019 ◽  
Vol 111 ◽  
pp. 04019
Author(s):  
Arash Rasooli ◽  
Laure Itard
Keyword(s):  
Heat Flux ◽  
Thermal Resistance ◽  
Average Method ◽  
Large Scale ◽  
Accurate Determination ◽  
Acceptable Result ◽  
Heat Flux Meter ◽  
The Difference

Determination of the thermo-physical characteristics of the buildings’ components is crucial to illustrate their thermal behavior and therefore their energy consumption. Along the same line, accurate determination of the thermal resistance of the building walls falls into one the most important targets. Following the difference between in-lab, and on site thermal performance of walls, in-situ measurements have been highly recommended. The most well-known practice for in-situ measurement of walls’ thermal resistance is the Average Method of ISO 9869, using one heat flux meter and two thermocouples. The method, in comparison with other existing methods is quite straight-forward and therefore, is applied widely in large scale. Despite its simplicity, this method usually needs a relatively long time to reach an acceptable result. The current paper deals with a modification to the ISO 9869 method, making it in many situations much quicker than its original state. Through simulation of walls of different typologies, it is shown in which cases the measurement period becomes longer than expected. It is demonstrated how the addition of a heat flux meter to the aforementioned equipment can lead to a much quicker achievement of the thermal resistance, following the rest of the instructions of the standard method.

scholarly journals Comparison of Infrared Thermography and Heat Flux Method for Dynamic Thermal Transmittance Determination

Buildings ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 132 ◽  
Author(s):  
Mergim Gaši ◽  
Bojan Milovanović ◽  
Sanjin Gumbarević
Keyword(s):  
Heat Flux ◽  
Infrared Thermography ◽  
Dynamic Method ◽  
Flux Method ◽  
Microsoft Excel ◽  
Experimental Procedure ◽  
Thermal Transmittance ◽  
U Value ◽  
Stationary Heat Transfer

This paper proposes an alternative experimental procedure that uses infrared thermography (IRT) for measuring the surface temperature of building elements, through which it is possible to approximate the thermal transmittance or the U-value. The literature review showed that all authors used similar procedures that require semi-stationary heat transfer conditions, which, in most cases, could not be achieved. The dynamic and the average methods that are given in ISO 9869 were also used with the IRT and the heat flux method (HFM). The dynamic method (DYNM) shows a higher level of accuracy compared to the average method (AVGM). Since the algorithm of the DYNM is more complicated than that of the AVGM, Microsoft Excel VBA was used to implement the algorithm of the DYNM. Using the procedure given in this paper, the U-value could be approximated within 0–30% of the design U-value. The use of IRT, in combination with the DYNM, could be used in-situ since the DYNM does not require stable boundary conditions. Furthermore, the procedure given in this paper could be used for relatively fast and inexpensive U-value approximation without the use of expensive equipment (e.g., heat flux sensors).

In Situ Experimental Validation of therm Finite Element Analysis for a High R-Value Wall Using Vacuum Insulation Panels

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Matthew J. Schiedel ◽  
Cynthia A. Cruickshank ◽  
Christopher M. Baldwin
Keyword(s):  
Finite Element ◽  
Thermal Resistance ◽  
Experimental Validation ◽  
Department Of Energy ◽  
Test Facility ◽  
Element Analysis ◽  
Theoretical Evaluation ◽  
Vacuum Insulation ◽  
R Value

This paper details the method used for a theoretical evaluation of Team Ontario's, U.S. Department of Energy Solar Decathlon 2013 entrant, high R-value wall using vacuum insulation panels (VIPs). The purpose is to determine a theoretical whole-wall thermal resistance to be used for energy modeling. Theoretical simulations are performed in therm, a two-dimensional finite element heat transfer modeling program, and an in situ experimental validation is conducted in Carleton University's Vacuum Insulation Test Facility located in Ottawa, Ontario, Canada. The theoretical model is refined based on the experimental study, and a whole-wall thermal resistance of Team Ontario's wall design is determined to be 9.4 m2·K/W (53 h·ft2·°F/Btu) at an exterior design temperature of −18 °C (0 °F).

scholarly journals Study and designed of an active infrared system for in-situ characterization of thermal resistance of building envelopes

2019 ◽  
Author(s):  
L. Gavérina ◽  
T. Ha ◽  
J. Waeytens ◽  
V. Feuillet ◽  
J-L. Manceau ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
In Situ Characterization ◽  
Building Envelopes

In-Situ Experimental Validation of THERM Finite Element Analysis for a High R-Value Wall Using Vacuum Insulation Panels

2013 ◽  
Author(s):  
Matthew Schiedel ◽  
Cynthia A. Cruickshank ◽  
Christopher Baldwin
Keyword(s):  
Finite Element ◽  
Thermal Resistance ◽  
Test Specimen ◽  
Experimental Validation ◽  
Weighted Average ◽  
Department Of Energy ◽  
Test Facility ◽  
Vacuum Insulation ◽  
R Value

Team Ontario is one of twenty collegiate teams selected to design and build a solar powered, net positive home for the U.S. Department of Energy Solar Decathlon 2013. One aspect of Team Ontario’s competition design entry is a high R-value wall using vacuum insulation panels. This paper details the method used for theoretical evaluation of the high R-value wall, stating all simplifying assumptions made. Theoretical simulations were performed in THERM, a two dimensional finite element heat transfer modelling program. Following a weighted average method used by industry experts, the whole-wall thermal resistance value was calculated. To verify the modelling results, an in-situ experimental validation was conducted. An 8′ × 8′ wall test specimen was built to the specifications of Team Ontario’s wall design. Experimental heat flux and temperature readings were collected from the test specimen in Carleton University’s Vacuum Insulation Test Facility located in Ottawa, Ontario, Canada, with the test specimen exposed to exterior weather elements. The experimental and theoretical results are compared and conclusions drawn to determine the effective thermal resistance of the vacuum insulation panels installed in the wall assembly. Finally the theoretical model is refined based on the previous study and a more accurate whole-wall thermal resistance of Team Ontario’s wall design is determined.

Sign in / Sign up

Export Citation Format

Share Document