scholarly journals Supercapacitor Storage Sizing Analysis for a Series Hybrid Vehicle

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1759 ◽  
Author(s):  
Massimiliano Passalacqua ◽  
Mauro Carpita ◽  
Serge Gavin ◽  
Mario Marchesoni ◽  
Matteo Repetto ◽  
...  

The increasing interest in Hybrid Electric Vehicles led to the study of new powertrain structures. In particular, it was demonstrated in the technical literature how series architecture can be more efficient, compared to parallel one, if supercapacitors are used as storage system. Since supercapacitors are characterized by high efficiency and high power density, but have low specific energy, storage sizing is a critical point with this technology. In this study, a detailed analysis on the effect of supercapacitor storage sizing on series architecture was carried out. In particular, in series architecture, supercapacitor storage sizing influences both engine number of starts and the energy that can be stored during regenerative braking. The first aspect affects the comfort, whereas the second aspect directly influences powertrain efficiency. Vehicle model and Energy Management System were studied and simulations were carried out for different storage energy, in order to define the optimal sizing.

Author(s):  
B. Prasanth ◽  
Deepa Kaliyaperumal ◽  
R. Jeyanthi ◽  
Saravanan Brahmanandam

In the present era, electric vehicles (EV) have revolutionized the world with their dominant features like cleanliness and high efficiency compared to that of the internal combustion (IC) engine-based vehicles. To crave for the higher efficiency of the EV during the braking, the kinetic energy of the EV is converted into electrical energy, which is harvested into storage system, called regenerative braking. Various techniques such as artificial neural network (ANN) and fuzzy-based controllers consider factors like state of charge of the battery and supercapacitor and brake demand for calculating the regenerative braking energy. A force distribution curve is designed to ensure that the braking force is distributed and applied on the four wheels simultaneously. In real-time optimization, an operating area is formed for maximizing the regenerative force which is evaluated by linear programming. It is proved that the drive range of the vehicle is increased by 25.7% compared to the one with non-RBS. In this work, RTO-based control loop for regenerative braking system is simulated in MATLAB/Simulink.


2011 ◽  
Vol 121-126 ◽  
pp. 3406-3410 ◽  
Author(s):  
Yang Yang ◽  
Yang Yang ◽  
Da Tong Qin ◽  
Jin Li

A new kind of pressure coordinated control system suite of regenerative braking system for hybrid electric vehicles (HEV) is proposed in this paper on the basis of appropriate transformation on traditional hydraulic braking system with ABS. AMEsim modular simulation platform is used to build a simulation model of the system. Dynamic performances of the key components and system are simulated and analyzed. And the simulation results show the effectiveness and feasibility of the pressure coordinated control system, which lays the foundation of the design and optimization for the regenerative braking system.


Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 430 ◽  
Author(s):  
F. P. Brito ◽  
Jorge Martins ◽  
Francisco Lopes ◽  
Carlos Castro ◽  
Luís Martins ◽  
...  

A range extender (RE) is a device used in electric vehicles (EVs) to generate electricity on-board, enabling them to significantly reduce the number of required batteries and/or extend the vehicle driving range to allow occasional long trips. In the present work, an efficiency-oriented RE based on a small motorcycle engine modified to the efficient over-expanded cycle, was analyzed, tested and simulated in a driving cycle. The RE was developed to have two points of operation, ECO: 3000 rpm, very high efficiency with only 15 kW; and BOOST: 7000 rpm with 35 kW. While the ECO strategy was a straightforward development for the over-expansion concept (less trapped air and a much higher compression ratio) the BOOST strategy was more complicated to implement and involved the need for throttle operation. Initially the concepts were evaluated in an in-house model and AVL Boost® (AVL List Gmbh, Graz, Austria), and proved feasible. Then, a BMW K75 engine was altered and tested on a brake dynamometer. The running engine proved the initial concept, by improving the efficiency for the ECO condition in almost 40% in relation to the stock engine and getting well over the required BOOST power, getting to 35 kW, while keeping an efficiency similar to the stock engine at the wide open throttle (WOT). In order to protect the engine during BOOST, the mixture was enriched, while at ECO the mixture was leaned to further improve efficiency. The fixed operation configuration allows the reduction, not only of complexity and cost of the RE, but also the set point optimization for the engine and generator. When integrated as a RE into a typical European light duty vehicle, it provided a breakthrough consumption reduction relatively to existing plug-in hybrid electric vehicles (PHEVs) in the market in the charge sustaining mode. The very high efficiency of the power generation seems to compensate for the loss of efficiency due to the excess electricity production, which must be stored in the battery. The results indicate that indeed it is possible to have an efficient solution, in-line with the electric mobility sustainability paradigm, which can solve most of the shortcomings of current EVs, notably those associated with batteries (range, cost and charging time) in a sustainable way.


Sign in / Sign up

Export Citation Format

Share Document