scholarly journals Evaluation of Biogas Production from the Co-Digestion of Municipal Food Waste and Wastewater Sludge at Refugee Camps Using an Automated Methane Potential Test System

Energies ◽  
2018 ◽  
Vol 12 (1) ◽  
pp. 32 ◽  
Author(s):  
Mohammad Al-Addous ◽  
Motasem N. Saidan ◽  
Mathhar Bdour ◽  
Mohammad Alnaief
Keyword(s):  
Food Waste ◽  
Organic Waste ◽  
Biogas Production ◽  
Test System ◽  
Wastewater Sludge ◽  
Methane Yield ◽  
Refugee Camps ◽  
Methane Potential ◽  
Municipal Food Waste ◽  
Potential Test

The potential benefits of the application of a circular economy—converting biomass at Za'atari Syrian refugee camps into energy—was investigated in this study. Representative organic waste and sludge samples were collected from the camp, mixed in different ratios, and analyzed in triplicate for potential biogas yield. Numerous calorific tests were also carried out. The tangential benefit of the co-digestion that was noticed was that it lowered the value of the total solid content in the mixture to the recommended values for wet digestion without the need for freshwater. To test the potential methane production, the automated methane potential test system (AMPTS) and the graduated tubes in the temperature-controlled climate room GB21 were utilized. Also, calorific values were determined for the organic waste and sludge on both a dry and a wet basis. The maximum biogas production from 100% organic waste and 100% sludge using AMPTS was 153 m3 ton-1 and 5.6 m3 ton-1, respectively. Methane yield reached its maximum at a Vs sub/ Vs inoculum range of 0.25–0.3. In contrast, the methane yield decreased when the Vs sub/ Vs inoculum exceeded 0.46. The optimum ratio of mixing of municipal food waste to sludge must be carefully selected to satisfy the demands of an energy production pilot plant and avoid the environmental issues associated with the sludge amount at wastewater treatment plants (WWTPs). A possible ratio to start with is 60–80% organic waste, which can produce 21–65 m3· biogas ton-1 fresh matter (FM). The co-digestion of organic waste and sludge can generate 38 Nm3/day of methane, which, in theory, can generate about 4 MW in remote refugee camps.

Determination of methane yield of cellulose using different experimental setups

2014 ◽  
Vol 70 (4) ◽  
pp. 599-604 ◽  
Author(s):  
Bing Wang ◽  
Ivo Achu Nges ◽  
Mihaela Nistor ◽  
Jing Liu
Keyword(s):  
Water Column ◽  
Test System ◽  
Methane Yield ◽  
Biochemical Methane Potential ◽  
Methane Potential ◽  
Bmp Test ◽  
Potential Test

In this work, biochemical methane potential (BMP) tests with cellulose as a model substrate were performed with the aid of three manually operated or conventional experimental setups (based on manometer, water column and gas bag) and one automated apparatus specially designed for analysis of BMP. The methane yields were 340 ± 18, 354 ± 13, 345 ± 15 and 366 ± 5 ml CH4/g VS obtained from experimental setups with manometer, water column, gas bag, and automatic methane potential test system, which corresponded to a biodegradability of 82, 85, 83 and 88% respectively. The results demonstrated that the methane yields of cellulose obtained from conventional and automatic experimental setups were comparable; however, the methane yield obtained from the automated apparatus showed greater precision. Moreover, conventional setups for the BMP test were more time- and labour-intensive compared with the automated apparatus.

scholarly journals Optimisation of C:N Ratio for Co-Digested Processed Industrial Food Waste and Sewage Sludge Using the BMP Test

2011 ◽  
Vol 9 (1) ◽  
Author(s):  
Zuhaib Siddiqui ◽  
N.J. Horan ◽  
Kofi Anaman
Keyword(s):  
Sewage Sludge ◽  
Food Waste ◽  
Biogas Production ◽  
C:N Ratio ◽  
Methane Yield ◽  
Biochemical Methane Potential ◽  
Volatile Solids ◽  
Methane Potential ◽  
Biomethane Production ◽  
Bmp Test

Biomethane production from processed industrial food waste (IFW) in admixture with sewage sludge (primary and waste activated sludge: PS and WAS) was evaluated at a range of C:N ratios using a standard biochemical methane potential (BMP) test. IFW alone had a C:N of 30 whereas for WAS it was 5.4 and thus the C:N ratio of the blends fell in that range. Increasing the IFW content in mix improves the methane potential by increasing both the cumulative biogas production and the rate of methane production. Optimum methane yield 239 mL/g VSremoved occurred at a C:N ratio of 15 which was achieved with a blend containing 11 percent (w/w) IFW. As the fraction of IFW in the blend increased, volatile solids (VS) destruction was increased and this led to a reduction in methane yield and amount of production. The highest destruction of volatile solids of 93 percent was achieved at C:N of 20 followed by C:N 30 and 15. A shortened BMP test is adequate for evaluating optimum admixtures.

Biogas Potentials Evaluation of Household Wastes in Johannesburg Metropolitan Area Using the Automatic Methane Potential Test System (AMPTS) II

2018 ◽  
Author(s):  
Kevin N. Nwaigwe ◽  
Abhishek Agarwal ◽  
Emmanuel E. Anyanwu
Keyword(s):  
Microcrystalline Cellulose ◽  
Metropolitan Area ◽  
Food Waste ◽  
Test System ◽  
Household Waste ◽  
Anaerobic Sludge ◽  
Co2 Absorption ◽  
Measuring Device ◽  
Methane Potential ◽  
Potential Test

A work on biogas potentials evaluation of household wastes in Johannesburg metropolitan area using the Automatic Methane Potential Test System (AMPTS) II is presented. The AMPTS II consists of three units — the sample incubation unit, CO2 absorption unit and the gas volume measuring device. Organic fraction of wastes collected from households within Johannesburg metropolis were sorted, ground and prepared into slurry by mixing with water. Microcrystalline cellulose powder with 3.5% loss on drying and 0.28g/cc density was used as control substrate while anaerobic sludge collected from a functional biogas reactor was used as inoculum. Anaerobic sludge was classified as sample A, household waste containing mainly non-food waste was labelled sample B, sample C was microcrystalline cellulose used as positive control while household waste composing of mainly food waste was classified as sample D. Each sample was fed into a 50 mL bottle reactor in triplicates and stirred in a clockwise direction continuously for 5 minutes with a pulse interval of 1 minute at a set temperature of 37°C for 30 days retention time. NaOH solution was prepared into solution following standard procedure and mixed with a prepared 0.4 % Thymolpthalein solution. The resultant solution was poured into the 100 mL bottles of the CO2 unit. Produced biogas was measured through water displacement in the volumetric bath and values read off through a data-logger connected to a laptop. Results indicated biochemical methane potential (BMP) of 69–800 NmL/gvs and biogas composition with more than 50% methane before CO2 fixing and over 80% after CO2 fixing. Given that the average amount of waste generated per person per day in South Africa is over 0.7 kg, there is huge potentials for biogas production from household wastes in Johannesburg.

scholarly journals Methane Potential from the Digestion of Food Waste in a Batch Reactor

2018 ◽  
Vol 7 (3.23) ◽  
pp. 36 ◽  
Author(s):  
Roslinda Seswoya ◽  
Ahmad Tarmizi Abdul Karim ◽  
Nur Aiza Darnak ◽  
Muhammad Fahmi Abd Rahman
Keyword(s):  
Food Waste ◽  
Methane Production ◽  
Yield Curve ◽  
Batch Reactor ◽  
Laboratory Data ◽  
Test System ◽  
Methane Yield ◽  
Lag Phase ◽  
Methane Potential ◽  
Bmp Test

The anaerobic digestibility of a targeted substrate, measured as methane yield is conducted via biochemical methane potential (BMP). In this study, the batch BMP test was conducted using Automatic Methane Potential Test System (AMPTS II) for 25 days and focused on the methane production from the digestion of food waste (FW, in the form of raw and diluted) at inoculum to substrate ratio (I/S) ratio of 2:0 and under mesophilic temperature.  The results showed that solids (TS and VS) concentration reduced significantly due to the       dilution. The ultimate methane yields from the digestion of raw FW and diluted FW were 1891.91ml CH4/gVS and 1983.96 ml CH4/gVS respectively. This showed that the dilution significantly improved the methane yield. In addition, the lag phase of the methane yield curve for both BMP tests was less than one (1) day, showing the good biodegradability of FW. The kinetic methane production from laboratory data and Modified Gompertz modelling fitted well. However, the kinetic equation parameters such as Mo, Rm and l from the model were slightly lower based on the observation of the laboratory data. 

scholarly journals Potential of biogas production from anaerobic co-digestion of fat, oil and grease waste and food waste

2018 ◽  
Vol 67 ◽  
pp. 02047 ◽  
Author(s):  
Reigina Sandriaty ◽  
Cindy Priadi ◽  
Septiana Kurnianingsih ◽  
Ayik Abdillah
Keyword(s):  
Anaerobic Digestion ◽  
Food Waste ◽  
Biogas Production ◽  
Potential Method ◽  
Methane Yield ◽  
Volatile Solid ◽  
Oil And Grease ◽  
Biochemical Methane Potential ◽  
Digestion Process ◽  
Methane Potential

The generation of fat, oil and grease (FOG) waste can be a nuisance hazard, but also a potential for resource recovery. FOG waste can be utilized as nutrient and energy source through anaerobic digestion which may increase methane yield but also increase presence of inhibitors. Using the biochemical methane potential method, this research is aimed to determine the effect of FOG waste in the co-digestion process of food waste (FW) to produce biogas. The research was conducted for 42 days at 37°C using FOG waste codigested with FW of 3 different volatile solid (VS) rasio which are 0.125, 0.3, and 0.5. The results showed that FOG waste combined with FW has a methane yield that may reach up to 485 ± 36.8 mL CH4/gr VS, the highest one produced by the 0.125 VS rasio mix. While the ratio of FOG waste with FW at 0.3 and 0.5 only produce 128 ± 195 and 4 ± 1.45 mL CH4/gr VS, respectively. The ratio of 0.125 also demonstrates the highest COD reduction of 56% compared to the other ratio which indicates the 0.125 FOG and FW ratio can be implemented to utilize FOG waste and increase methane yield during anaerobic digestion process.

scholarly journals The Performance Evaluation on Co-Digestion of Domestic Sewage Sludge and Food Waste for Methane Yield and Kinetics Analysis

2021 ◽  
Vol 13 (3) ◽  
Author(s):  
Siti Mariam Sulaiman ◽  
◽  
Roslinda Seswoya ◽  
Keyword(s):  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Methane Production ◽  
Test System ◽  
Domestic Sewage ◽  
Methane Yield ◽  
Methane Potential ◽  
Methane Production Rate ◽  
Bmp Test

Sewage sludge and food waste; are organic wastes suitable for the anaerobic digestion. However, the digestion of sewage sludge and food waste as solely substrate is having a drawback in term of methane yield. Therefore, many researchers combined these two wastes as a co-substrate and used in co-digestion. This study focused to evaluate the anaerobic co-digestion of domestic sewage sludge (in form of primary and secondary sewage sludge) with food waste under mesophilic temperature in a batch assay. Two series of batch biochemical methane potential (BMP) test were conducted using the Automatic Methane Potential Test System (AMPTS II). Each set are labelled with BMP 1(PSS:FW) and BMP 2 (SSS:FW). The BMP tests were monitored automatically until the methane production is insignificant. Using the data observed in the laboratory, the kinetic paremeters were calculated. Also, the First-order and Modified Gompertz modeling were included to predict the anaerobic digestion performance. Finding showed that BMP 1(PSS:FW) have better performance with respect to the higher ultimate methane yield and methane production rate as compared to BMP 2 (SSS:FW). Besides, the kinetic parameters from laboratory work and modeling were slightly different. In which the kinetic paremetes from modelling is lesser. However, both modelling are well fitted to the experimental data with high correlation coefficient, R2 ranged from 0.993 to 0.997.

scholarly journals Sugarcane Bagasse as a Co-Substrate with Oil-Refinery Biological Sludge for Biogas Production Using Batch Mesophilic Anaerobic Co-Digestion Technology: Effect of Carbon/Nitrogen Ratio

Water ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 590
Author(s):  
Aiban Abdulhakim Saeed Ghaleb ◽  
Shamsul Rahman Mohamed Kutty ◽  
Gasim Hayder Ahmed Salih ◽  
Ahmad Hussaini Jagaba ◽  
Azmatullah Noor ◽  
...  
Keyword(s):  
Anaerobic Digestion ◽  
Sugarcane Bagasse ◽  
Organic Waste ◽  
Wastewater Treatment Plants ◽  
Biogas Production ◽  
Raw Materials ◽  
Oil Refinery ◽  
Methane Yield ◽  
Oil Refineries ◽  
Biological Sludge

Man-made organic waste leads to the rapid proliferation of pollution around the globe. Effective bio-waste management can help to reduce the adverse effects of organic waste while contributing to the circular economy at the same time. The toxic oily-biological sludge generated from oil refineries’ wastewater treatment plants is a potential source for biogas energy recovery via anaerobic digestion. However, the oily-biological sludge’s carbon/nitrogen (C/N) ratio is lower than the ideal 20–30 ratio required by anaerobic digestion technology for biogas production. Sugarcane bagasse can be digested as a high C/N co-substrate while the oily-biological sludge acts as a substrate and inoculum to improve biogas production. In this study, the best C/N with co-substrate volatile solids (VS)/inoculum VS ratios for the co-digestion process of mixtures were determined empirically through batch experiments at temperatures of 35–37 °C, pH (6–8) and 60 rpm mixing. The raw materials were pre-treated mechanically and thermo-chemically to further enhance the digestibility. The best condition for the sugarcane bagasse delignification process was 1% (w/v) sodium hydroxide, 1:10 solid-liquid ratio, at 100 °C, and 150 rpm for 1 h. The results from a 33-day batch anaerobic digestion experiment indicate that the production of biogas and methane yield were concurrent with the increasing C/N and co-substrate VS/inoculum VS ratios. The total biogas yields from C/N 20.0 with co-substrate VS/inoculum VS 0.06 and C/N 30.0 with co-substrate VS/inoculum VS 0.18 ratios were 2777.0 and 9268.0 mL, respectively, including a methane yield of 980.0 and 3009.3 mL, respectively. The biogas and methane yield from C/N 30.0 were higher than the biogas and methane yields from C/N 20.0 by 70.04 and 67.44%, respectively. The highest biogas and methane yields corresponded with the highest C/N with co-substrate VS/inoculum VS ratios (30.0 and 0.18), being 200.6 mL/g VSremoved and 65.1 mL CH4/g VSremoved, respectively.

scholarly journals Biogas potential of organic waste onboard cruise ships — a yet untapped energy source

2021 ◽  
Author(s):  
Kai Schumüller ◽  
Dirk Weichgrebe ◽  
Stephan Köster
Keyword(s):  
Energy Source ◽  
Anaerobic Digestion ◽  
Sewage Sludge ◽  
Food Waste ◽  
Energy Demand ◽  
Organic Waste ◽  
Biogas Production ◽  
Biogas Yield ◽  
Cruise Ships ◽  
Detailed Presentation

AbstractTo tap the organic waste generated onboard cruise ships is a very promising approach to reduce their adverse impact on the maritime environment. Biogas produced by means of onboard anaerobic digestion offers a complementary energy source for ships’ operation. This report comprises a detailed presentation of the results gained from comprehensive investigations on the gas yield from onboard substrates such as food waste, sewage sludge and screening solids. Each person onboard generates a total average of about 9 kg of organic waste per day. The performed analyses of substrates and anaerobic digestion tests revealed an accumulated methane yield of around 159 L per person per day. The anaerobic co-digestion of sewage sludge and food waste (50:50 VS) emerged as particularly effective and led to an increased biogas yield by 24%, compared to the mono-fermentation. In the best case, onboard biogas production can provide an energetic output of 82 W/P, on average covering 3.3 to 4.1% of the total energy demand of a cruise ship.

Solubilization of waste activated sludge by alkaline pretreatment and biochemical methane potential (BMP) tests for anaerobic co-digestion of municipal organic waste

2003 ◽  
Vol 48 (8) ◽  
pp. 211-219 ◽  
Author(s):  
N.-H. Heo ◽  
S.-C. Park ◽  
J.-S. Lee ◽  
H. Kang
Keyword(s):  
Activated Sludge ◽  
Food Waste ◽  
Organic Waste ◽  
Waste Activated Sludge ◽  
Feed Mixture ◽  
Biochemical Methane Potential ◽  
Methane Recovery ◽  
Attractive Option ◽  
Methane Potential ◽  
Anaerobic Digestibility

Biochemical methane potential (BMP) tests have been carried out to determine the anaerobic digestibility of the waste activated sludge (WAS) and the sludge pretreated by NaOH (PWAS). The optimal NaOH dosage was determined to be 45 meq NaOH/L. The maximum SCOD solubilization was 27.7, 31.4 and 38.3% at the temperatures of 25, 35 and 55°C respectively after 4 hours reaction. The final methane yield of simulated food waste (SFW) was 430 ml CH4/g VSadded, and those of PWAS (25°C), PWAS (35°C) and PWAS (55°C) was 274, 286 and 310 ml CH4/g VSadded respectively after 20 days. The figures were 66%, 73% and 88% higher than that of WAS. The methane production in anaerobic co-digestion is considerably affected by the fraction of SFW and PWAS in the feed. The anaerobic digestibility of the feed mixture (SFW with PWAS) is higher than that of the feed mixture (SFW with WAS). Anaerobic co-digestion of food waste with the PWAS is found to be an attractive option to reduce the solid waste volume with improved methane recovery.

Sign in / Sign up

Export Citation Format

Share Document