scholarly journals A New Rail-to-Rail Second Generation Voltage Conveyor

Electronics ◽  
2019 ◽  
Vol 8 (11) ◽  
pp. 1292 ◽  
Author(s):  
Barile ◽  
Stornelli ◽  
Ferri ◽  
Safari ◽  
D’Amico
Keyword(s):  
Second Generation ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Total Power ◽  
Voltage Range ◽  
Class Ab ◽  
Rail To Rail ◽  
Total Power Consumption ◽  
Voltage Swing

In this paper, a novel low voltage low power CMOS second generation voltage conveyor (VCII) with an improved voltage range at both the X and Z terminals is presented. The proposed VCII is formed by a current buffer based on a class AB regulated common-gate stage and a modified rail-to-rail voltage buffer. Spice simulation results using LFoundry 0.15 μm low-Vth CMOS technology with a ±0.9 V supply voltage are provided to demonstrate the validity of the designed circuit. Thanks to the class AB behavior, from a bias current of 10 µA, the proposed VCII is capable of driving 0.5 mA on the X terminal, with a total power consumption of 120 µW. The allowed voltage swing on the Z terminal is at least equal to ±0.83 V, while on the X terminals it is ±0.72 V. Both DC and AC voltage and current gains are provided, and time domain simulations, where the voltage conveyor is used as a transimpedance amplifier (TIA), are also presented. A final table that summarizes the main features of the circuit, comparing them with the literature, is also given.

scholarly journals Towards Realization of a Low-Voltage Class-AB VCII with High Current Drive Capability

Electronics ◽  
2021 ◽  
Vol 10 (18) ◽  
pp. 2303
Author(s):  
Leila Safari ◽  
Gianluca Barile ◽  
Vincenzo Stornelli ◽  
Shahram Minaei ◽  
Giuseppe Ferri
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Harmonic Distortion ◽  
Cmos Technology ◽  
Current Drive ◽  
Total Power ◽  
High Signal ◽  
High Current ◽  
Class Ab ◽  
Total Power Consumption

In this paper, the implementation of a low-voltage class AB second generation voltage conveyor (VCII) with high current drive capability is presented. Simple realization and good overall performance are the main features of the proposed circuit. Proper solutions and techniques were used to achieve high signal swing and high linearity at Y, X and Z ports of VCII as well as low-voltage operation. The operation of the proposed VCII was verified through SPICE simulations based on TSMC 0.18 µm CMOS technology parameters and a supply voltage of ±0.9 V. The small signal impedance values were 973 Ω, 120 kΩ and 217 Ω at Y, X and Z ports, respectively. The maximum current at the X port was ±10 mA with maximum total harmonic distortion (THD) of 2.4% at a frequency of 1 MHz. Considering a bias current (IB) of 29 µA and output current at the X port (IX) of 10 mA, the current drive capability (IX/IB) of about 345 was achieved at the X port. The voltage swing at the Z port was (−0.4, 0.4) V. The THD value at the Z port for an input signal with 0.8 V peak-to-peak value and frequency of 1 MHz was 3.9%. The total power consumption was 0.393 µW.

scholarly journals 1.5-V CMOS Current Multiplier/Divider

2018 ◽  
Vol 8 (3) ◽  
pp. 1478 ◽  
Author(s):  
Jetsdaporn Satansup ◽  
Worapong Tangsrirat
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Total Power ◽  
Total Power Consumption ◽  
Linearity Error ◽  
Low Supply Voltage ◽  
Circuit Technique

A circuit technique for designing a compact low-voltage current-mode multiplier/divider circuit in CMOS technology is presented.  It is based on the use of a compact current quadratic cell able to operate at low supply voltage.  The proposed circuit is designed and simulated for implementing in TSMC 0.25-m CMOS technology with a single supply voltage of 1.5 V.  Simulation results using PSPICE, accurately agreement with theoretical ones, have been provided, and also demonstrate a maximum linearity error of 1.5%, a THD less than 2% at 100 MHz, a total power consumption of 508 W, and -3dB small-signal frequency of about 245 MHz.

New Schmitt Trigger with Controllable Hysteresis using Dual Control Gate-Floating Gate Transistor (DCG-FGT)

2013 ◽  
Vol 2 (1) ◽  
pp. 49
Author(s):  
Abderrezak Marzaki ◽  
V. Bidal ◽  
R. Laffont ◽  
W. Rahajandraibe ◽  
J-M. Portal ◽  
...  
Keyword(s):  
Low Voltage ◽  
Schmitt Trigger ◽  
Cmos Technology ◽  
Floating Gate ◽  
Dual Control ◽  
Switching Voltage ◽  
Voltage Range ◽  
Rail To Rail ◽  
Floating Gate Transistor ◽  
Simulation Results

This paper presents different low voltage adjustable CMOS Schmitt trigger using DCG-FGT transistor. Simple circuits are introduced to provide flexibility to program the hysteresic threshold in this paper. The hysteresis can be controlled accurately at a large voltage range. The proposed Schmitt trigger have been designed using 90nm 1.2V CMOS technology and simulated using Eldo with PSP device models. The simulation results show rail-to-rail operation and adjustable switching voltages <em>V<sub>TH- </sub></em>(low switching voltage) and <em>V<sub>TH+ </sub></em>(high switching voltage).

A 16.4 nW, Sub-1 V, Resistor-Less Voltage Reference with BJT Voltage Divider

2018 ◽  
Vol 27 (13) ◽  
pp. 1850206 ◽  
Author(s):  
Qingshan Yang ◽  
Peiqing Han ◽  
Niansong Mei ◽  
Zhaofeng Zhang
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Voltage Divider ◽  
Total Power ◽  
Cmos Process ◽  
Operating Voltage ◽  
Voltage Reference ◽  
Ultra Low Power ◽  
Silicon Area ◽  
Total Power Consumption

A 16.4[Formula: see text]nW, sub-1[Formula: see text]V voltage reference for ultra-low power low voltage applications is proposed. This design reduces the operating voltage to 0.8[Formula: see text]V by a BJT voltage divider and decreases the silicon area considerably by eliminating resistors. The PTAT and CTAT are based on SCM structures and a scaled-down [Formula: see text], respectively, to improve the process insensitivity. This work is fabricated in 0.18[Formula: see text][Formula: see text]m CMOS process with a total area of 0.0033[Formula: see text]mm2. Measured results show that it works properly for supply voltage from 0.8[Formula: see text]V to 2[Formula: see text]V. The reference voltage is 467.2[Formula: see text]mV with standard deviation ([Formula: see text]) being 12.2 mV and measured TC at best is 38.7[Formula: see text]ppm/[Formula: see text]C ranging from [Formula: see text]C to 60[Formula: see text]C. The total power consumption is 16.4[Formula: see text]nW under the minimum supply voltage at 27[Formula: see text]C.

Feedforward Bulk-Driven Class AB Fully-Differential Second-Generation Current Conveyor (FDCCII)

2014 ◽  
Vol 979 ◽  
pp. 62-65
Author(s):  
Thawatchai Thongleam ◽  
Varakorn Kasemsuwan
Keyword(s):  
Second Generation ◽  
Transfer Characteristic ◽  
Cmos Technology ◽  
Circuit Performance ◽  
Input Stage ◽  
Class Ab ◽  
Fully Differential ◽  
Rail To Rail ◽  
Differential Pair ◽  
Dc Current

In this paper, a feedforward bulk-driven class AB fully-differential second-generation current conveyer (FDCCII) is presented. Bulk-driven differential pair is employed for the input stage allowing the FDCCII to operate with rail-to-rail operation. Feedfoward technique is also incorporated into input stage to increase the DC gain and minimize the common mode gain. The circuit performance is verified using HSPICE in 0.18 μm CMOS technology. The simulation results show rail-to-rail input and output swings. The DC voltage transfer characteristic between ports Y and X and DC current transfer characteristic between ports X and Z shows good linearity. The bandwidths show 25.7 MHz (VX/VY), 30 MHz (IZ/IX), respectively. The power dissipation is 267.5 μW.

130 nm CMOS Bulk-Driven Variable Gain Amplifier for Low-Voltage Applications

2017 ◽  
Vol 26 (08) ◽  
pp. 1740003 ◽  
Author(s):  
Daniel Arbet ◽  
Viera Stopjaková ◽  
Martin Kováč ◽  
Lukáš Nagy ◽  
Matej Rakús ◽  
...  
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Input Voltage ◽  
Cmos Technology ◽  
Variable Gain Amplifier ◽  
Voltage Range ◽  
Variable Gain ◽  
Wide Scale ◽  
Simulation Results ◽  
Low Supply Voltage

In this paper, a variable gain amplifier (VGA) designed in 130 nm CMOS technology is presented. The proposed amplifier is based on the bulk-driven (BD) design approach, which brings a possibility to operate with low supply voltage. Since the supply voltage of only 0.6 V is used for the amplifier to operate, there is no risk of latch-up event that usually represents the main drawback of the BD circuit systems. BD transistors are employed in the input differential stage, which makes it possible to operate in rail-to-rail input voltage range. Achieved simulation results indicate that gain of the proposed VGA can be varied in a wide scale, which together with the low supply voltage feature make the proposed amplifier useful for low-voltage and low-power applications. An additional circuit responsible for maintaining the linear-in-decibel gain dependency of the VGA is also addressed. The proposed circuit block avails arbitrary shaping of the curve characterizing the gain versus the controlling voltage dependency.

scholarly journals Low-Power High-Speed Double Gate 1-bit Full Adder Cell

2016 ◽  
Vol 62 (4) ◽  
pp. 329-334 ◽  
Author(s):  
Raushan Kumar ◽  
Sahadev Roy ◽  
C.T. Bhunia
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Average Power ◽  
Full Adder ◽  
Cmos Technology ◽  
Spice Simulation ◽  
Pass Transistor ◽  
Voltage Swing

Abstract In this paper, we proposed an efficient full adder circuit using 16 transistors. The proposed high-speed adder circuit is able to operate at very low voltage and maintain the proper output voltage swing and also balance the power consumption and speed. Proposed design is based on CMOS mixed threshold voltage logic (MTVL) and implemented in 180nm CMOS technology. In the proposed technique the most time-consuming and power consuming XOR gates and multiplexer are designed using MTVL scheme. The maximum average power consumed by the proposed circuit is 6.94μW at 1.8V supply voltage and frequency of 500 MHz, which is less than other conventional methods. Power, delay, and area are optimized by using pass transistor logic and verified using the SPICE simulation tool at desired broad frequency range. It is also observed that the proposed design may be successfully utilized in many cases, especially whenever the lowest power consumption and delay are aimed.

scholarly journals 60 GHz Front-End Components for Broadband Wireless Communication in 130 nm CMOS Technology

2016 ◽  
Vol 21 (1) ◽  
pp. 67-77
Author(s):  
Vasilis Kolios ◽  
Konstantinos Giannakidis ◽  
Grigorios Kalivas
Keyword(s):  
Power Consumption ◽  
Phase Noise ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Total Power ◽  
Spectral Space ◽  
60 Ghz ◽  
Front End ◽  
Total Power Consumption ◽  
5 Ghz

Abstract The over 5 GHz available spectral space allocated worldwide around the 60 GHz band, is very promising for very high data rate wireless short-range communications. In this article we present two key components for the 60 GHz front-end of a transceiver, in 130 nm RF CMOS technology: a single-balanced mixer with high Conversion Gain (CG), reduced Noise Figure (NF) and low power consumption, and an LC cross-coupled Voltage Controlled Oscillator (VCO) with very good linearity, with respect to Vctrl, and very low Phase Noise (PN). In both circuits, custom designed inductors and a balun structure for the mixer are employed, in order to enhance their performance. The VCO’s inductor achieves an inductance of 198 pH and a quality factor (Q) of 30, at 30 GHz. The balun shows less than 1o Phase Imbalance (PI) and less than 0.2 dB Amplitude Imbalance (AI), from 57 to 66 GHz. The mixer shows a CG greater than 15 dB and a NF lower than 12 dB. In addition, the VCO achieves a Phase Noise lower than -106 dBc/Hz at 1 MHz offset, and shows great linearity for the entire band. Both circuits are biased with a 1.2 V supply voltage and the total power consumption is about 10.6 mW for the mixer and 10.92 mW for the VCO.

scholarly journals Analysis of CMOS Comparator in 90nm Technology with Different Power Reduction Techniques

2018 ◽  
Vol 8 (6) ◽  
pp. 4922
Author(s):  
Anil Khatak ◽  
Manoj Kumar ◽  
Sanjeev Dhull
Keyword(s):  
Power Consumption ◽  
Leakage Current ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Power Reduction ◽  
Total Power ◽  
Low Power Consumption ◽  
Power Gating ◽  
Reduction Techniques ◽  
Total Power Consumption

To reduce power consumption of regenerative comparator three different techniques are incorporated in this work. These techniques provide a way to achieve low power consumption through their mechanism that alters the operation of the circuit. These techniques are pseudo NMOS, CVSL (cascode voltage switch logic)/DCVS (differential cascode voltage switch) &amp; power gating. Initially regenerative comparator is simulated at 90 nm CMOS technology with 0.7 V supply voltage. Results shows total power consumption of 15.02 μW with considerably large leakage current of 52.03 nA. Further, with pseudo NMOS technique total power consumption increases to 126.53 μW while CVSL shows total power consumption of 18.94 μW with leakage current of 1270.13 nA. More then 90% reduction is attained in total power consumption and leakage current by employing the power gating technique. Moreover, the variations in the power consumption with temperature is also recorded for all three reported techniques where power gating again show optimum variations with least power consumption. Four more conventional comparator circuits are also simulated in 90nm CMOS technology for comparison. Comparison shows better results for regenerative comparator with power gating technique. Simulations are executed by employing SPICE based on 90 nm CMOS technology.

Nano Power Current Reference Circuit consisting of Sub-threshold CMOS Circuits

2017 ◽  
Vol 2 (1) ◽  
pp. 1-4
Author(s):  
Dinesh Kushwaha ◽  
D. K. Mishra
Keyword(s):  
Large Scale ◽  
Low Voltage ◽  
Supply Voltage ◽  
Circuit Simulation ◽  
Current Source ◽  
Cmos Technology ◽  
Threshold Region ◽  
Voltage Range ◽  
Current Reference ◽  
Reference Circuit

This paper proposes a low voltage CMOS Nano power current reference circuit and presents its performance with circuit simulation in 180- nm UMC CMOS technology. The proposed circuit consists of start-up, Bias-voltage, current-source sub-circuits with most of the MOSFETs operating in sub-threshold region. Simulation results shows that the circuit generates a stable reference current of 4-nA in supply voltage range 1 V- 1.8 V with line sensitivity of 0.203%/V.The temperature coefficient of the current was 7592ppm/°C at 1.8 V in the range of 0°C-100°C. The power dissipation was 380 NW at 1.8 V Supply. The proposed circuit would be suitable for use in sub-threshold –operated power-aware large-scale integration

Sign in / Sign up

Export Citation Format

Share Document