scholarly journals A Novel OTA Architecture Exploiting Current Gain Stages to Boost Bandwidth and Slew-Rate

Electronics ◽  
2021 ◽  
Vol 10 (14) ◽  
pp. 1638
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Current Gain ◽  
Small Signal ◽  
Slew Rate ◽  
Large Signal ◽  
Current Mirrors ◽  
Order Of Magnitude ◽  
Unity Gain ◽  
Architecture And Design

A novel architecture and design approach which make it possible to boost the bandwidth and slewrate performance of operational transconductance amplifiers (OTAs) are proposed and employed to design a low-power OTA with top-of-class small-signal and large-signal figures of merit (FOMs). The proposed approach makes it possible to enhance the gain, bandwidth and slew-rate for a given power consumption and capacitive load, achieving more than an order of magnitude better performance than a comparable conventional folded cascode amplifier. Current mirrors with gain and a push–pull topology are exploited to achieve symmetrical sinking and sourcing output currents, and hence class-AB behavior. The resulting OTA was implemented using the 130 nm STMicroelectronics process, with a supply voltage of 1 V and a power consumption of only 1 µW. Simulations with a 200 pF load capacitance showed a gain of 92 dB, a unity-gain frequency of 141 kHz, and a peak slew-rate of 30 V/ms, with a phase margin of 80°, and good noise, PSRR and CMRR performance. The small-signal and large-signal current and power FOMs are the highest reported in the literature for comparable amplifiers. Extensive parametric and Monte Carlo simulations show that the OTA is robust against process, supply voltage and temperature (PVT) variations, as well as against mismatches.

scholarly journals FIN-FET BASED HIGH GAIN OP-AMP WITH SLEW RATE ENHANCEMENT IN 45-NM REGIME

2020 ◽  
Vol 6 (7) ◽  
pp. 27-33
Author(s):  
Nagendra Tiwari ◽  
Bharati Chourasia
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
High Gain ◽  
Silicon On Insulator ◽  
Slew Rate ◽  
Video Signals ◽  
Op Amp ◽  
Dynamic Biasing ◽  
Unity Gain ◽  
Two Stages

In this paper dynamic biasing technique is used for the enhancing the slew rate of the designed Op-Amp. The proposed FinFET based Op-Amp has been verified through Hspice simulator in the standard 45nm Silicon on Insulator FinFET library. The proposed op amp has two stages Miller compensated configuration. A biasing circuit (DSB circuit) is used for dynamic switching of the biasing voltage of the op amp. This leads to lower power consumption, wide ICMR range, and high gain stability. The proposed op amp has a power consumption of 661.83 μW. It has a dual supply voltage of -1.0V and 1.0V. The input common mode range (ICMR) is -800 mV to +900 mV. The Op-Amp has a slew rate of 1.5 KV/μs. Voltage gain of the op amp is 90.4dB. Due to the use of SOI FINFET devices the op amp has relatively less leakage current as compared to similar bulk MOSFET device op amps. The op amp has unity gain bandwidth of 1.27 GHz. Thus, it can be used to transmission and processing of audio and video signals.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Design of High Gain Folded Cascode OTA-Based Transconductance–Capacitance Loop Filter for PLL Applications

2021 ◽  
pp. 2150263
Author(s):  
Priti Gupta ◽  
Sanjay Kumar Jana
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
High Gain ◽  
Cmos Process ◽  
Operational Transconductance Amplifier ◽  
Loop Filter ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Unity Gain ◽  
Folded Cascode

This paper deals with the designing of low-power transconductance–capacitance-based loop filter. The folded cascode-based operational transconductance amplifier (OTA) is designed in this paper with the help of quasi-floating bulk MOSFET that achieved the DC gain of 88.61[Formula: see text]dB, unity gain frequency of 97.86[Formula: see text]MHz and power consumption of 430.62[Formula: see text][Formula: see text]W. The proposed OTA is compared with the exiting OTA structure which showed 19.50% increase in DC gain and 15.11% reduction in power consumption. Further, the proposed OTA is used for the designing of transconductance–capacitance-based loop filter that has been operated at [Formula: see text]3[Formula: see text]dB cut-off frequency of 30.12[Formula: see text]MHz with the power consumption of 860.90[Formula: see text][Formula: see text]W at the supply voltage of [Formula: see text][Formula: see text]V. The transistor-level simulation has been done in 0.18[Formula: see text][Formula: see text]m CMOS process.

scholarly journals Current mode approach: High performance 0.35 μm CMOS class AB push-pull current amplifier

2003 ◽  
Vol 16 (2) ◽  
pp. 195-204
Author(s):  
Lyes Bouzerara ◽  
Mohand Belaroussi
Keyword(s):  
High Performance ◽  
Supply Voltage ◽  
Current Mode ◽  
Current Gain ◽  
Design Parameters ◽  
Power Supply Voltage ◽  
Current Amplifier ◽  
Class Ab ◽  
Current Mirrors ◽  
General Circuits

A very high bandwidth class AB (Push-Pull) current amplifier using the compensation resistor technique is presented and analyzed. Such technique stands as a powerful method of bandwidth enhancement for general circuits using CMOS current mirrors. The proposed bandwidth is enhanced from 675 MHz for the uncompensated current amplifier to 745MHz for the compensated one without affecting the current gain and other design parameters such as power consumption and output swing. The circuit exhibits a current gain of 20 dB and consumes 1.48 mW for ?2.5V power supply voltage. All simulation results were performed using Hspice tool with 0.35^m CMOS TSMC parameters.

Statistical Simulations on Perceptron-Based Adders

2011 ◽  
pp. 1474-1481
Author(s):  
Snorre Aunet ◽  
Hans Kristian Otnes Berge
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Reducing Power ◽  
Process Variations ◽  
Full Adder ◽  
Cmos Technology ◽  
Subthreshold Cmos ◽  
Order Of Magnitude ◽  
Supply Voltages ◽  
Circuit Technique

In this article we compare a number of full-adder (1- bit addition) cells regarding minimum supply voltage and yield, when taking statistical simulations into account. According to the ITRS Roadmap two of the most important challenges for future nanoelectronics design are reducing power consumption and increasing manufacturability (ITRS, 2005). We use subthreshold CMOS, which is regarded by many as the most promising ultra low power circuit technique. It is also shown that a minimum redundancyfactor as low as 2 is sufficient to make circuits maintain full functionality under the presence of defects. This is, to our knowledge, the lowest redundancy reported for comparable circuits, and builds on a method suggested a few years ago (Aunet & Hartmann, 2003). A standard Full-Adder (FA) and an FA based on perceptrons exploiting the “mirrored gate”, implemented in a standard 90 nm CMOS technology, are shown not to withstand statistical mismatch and process variations for supply voltages below 150 mV. Exploiting a redundancy scheme tolerating “open” faults, with gate-level redundancy and shorted outputs, shows that the same two FAs might produce adequate Sum and Carry outputs at the presence of a defect PMOS for supply voltages above 150 mV, for a redundancy factor of 2 (Aunet & Otnes Berge, 2007). Two additional perceptrons do not tolerate the process variations, according to simulations. Simulations suggest that the standard FA has the lowest power consumption. Power consumption varies more than an order of magnitude for all subthreshold FAs, due to the statistical variations

MESFET large-signal model based on small-signal measurements for time-domain CAD

1988 ◽  
Vol 24 (15) ◽  
pp. 973 ◽  
Author(s):  
A. Ouslimani ◽  
G. Vernet ◽  
J.C. Henaux ◽  
P. Crozat ◽  
R. Adde
Keyword(s):  
Time Domain ◽  
Small Signal ◽  
Large Signal ◽  
Signal Model ◽  
Model Based

scholarly journals A High Efficiency Low Noise RF-to-DC Converter Employing Gm-Boosting Envelope Detector and Offset Canceled Latch Comparator

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1078
Author(s):  
Thi Thuy Pham ◽  
Dongmin Kim ◽  
Seo-Hyeong Jeong ◽  
Junghyup Lee ◽  
Donggu Im
Keyword(s):  
Power Consumption ◽  
High Efficiency ◽  
Supply Voltage ◽  
Current Source ◽  
Low Noise ◽  
The Body ◽  
Common Source ◽  
Conversion Gain ◽  
Input Transistor ◽  
Envelope Detector

This work presents a high efficiency RF-to-DC conversion circuit composed of an LC-CL balun-based Gm-boosting envelope detector, a low noise baseband amplifier, and an offset canceled latch comparator. It was designed to have high sensitivity with low power consumption for wake-up receiver (WuRx) applications. The proposed envelope detector is based on a fully integrated inductively degenerated common-source amplifier with a series gate inductor. The LC-CL balun circuit is merged with the core of the envelope detector by sharing the on-chip gate and source inductors. The proposed technique doubles the transconductance of the input transistor of the envelope detector without any extra power consumption because the gate and source voltage on the input transistor operates in a differential mode. This results in a higher RF-to-DC conversion gain. In order to improve the sensitivity of the wake-up radio, the DC offset of the latch comparator circuit is canceled by controlling the body bias voltage of a pair of differential input transistors through a binary-weighted current source cell. In addition, the hysteresis characteristic is implemented in order to avoid unstable operation by the large noise at the compared signal. The hysteresis window is programmable by changing the channel width of the latch transistor. The low noise baseband amplifier amplifies the output signal of the envelope detector and transfers it into the comparator circuit with low noise. For the 2.4 GHz WuRx, the proposed envelope detector with no external matching components shows the simulated conversion gain of about 16.79 V/V when the input power is around the sensitivity of −60 dBm, and this is 1.7 times higher than that of the conventional envelope detector with the same current and load. The proposed RF-to-DC conversion circuit (WuRx) achieves a sensitivity of about −65.4 dBm based on 45% to 55% duty, dissipating a power of 22 μW from a 1.2 V supply voltage.

scholarly journals A Novel Cross-Latch Shift Register Scheme for Low Power Applications

2020 ◽  
Vol 11 (1) ◽  
pp. 129
Author(s):  
Po-Yu Kuo ◽  
Ming-Hwa Sheu ◽  
Chang-Ming Tsai ◽  
Ming-Yan Tsai ◽  
Jin-Fa Lin
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Electrical Power ◽  
Average Power ◽  
Leakage Power ◽  
Shift Register ◽  
Cmos Process ◽  
Average Power Consumption ◽  
Simulation Results ◽  
Layout Area

The conventional shift register consists of master and slave (MS) latches with each latch receiving the data from the previous stage. Therefore, the same data are stored in two latches separately. It leads to consuming more electrical power and occupying more layout area, which is not satisfactory to most circuit designers. To solve this issue, a novel cross-latch shift register (CLSR) scheme is proposed. It significantly reduced the number of transistors needed for a 256-bit shifter register by 48.33% as compared with the conventional MS latch design. To further verify its functions, this CLSR was implemented by using TSMC 40 nm CMOS process standard technology. The simulation results reveal that the proposed CLSR reduced the average power consumption by 36%, cut the leakage power by 60.53%, and eliminated layout area by 34.76% at a supply voltage of 0.9 V with an operating frequency of 250 MHz, as compared with the MS latch.

PERFECT case studies demonstrating order of magnitude reduction in power consumption

2016 ◽  
Author(s):  
David K. Wittenberg ◽  
Edin Kadric ◽  
Andre DeHon ◽  
Jonathan Edwards ◽  
Jeffrey Smith ◽  
...  
Keyword(s):  
Power Consumption ◽  
Case Studies ◽  
Order Of Magnitude
Sign in / Sign up

Export Citation Format

Share Document