scholarly journals Design and Implementation Procedure of a High-Gain Three-Input Step-Up 1 kW Converter

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 625 ◽  
Author(s):  
Edgardo Netzahuatl-Huerta ◽  
Leobardo Hernandez-Gonzalez ◽  
Domingo Cortes ◽  
Jazmin Ramirez-Hernandez
Keyword(s):  
Renewable Energy ◽  
High Efficiency ◽  
Renewable Energy Sources ◽  
High Gain ◽  
Power Converter ◽  
Open Loop ◽  
Energy Sources ◽  
Storage Element ◽  
Grid Systems ◽  
Different Characteristics

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed, such as energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter is able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim; however, most of them are based on multistage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter, easy to control in open loop condition, is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain and less storage element, keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially designed for photovoltaic applications is enabled to be used in medium- and high-power applications, for example, when renewable energy sources are used.

scholarly journals A Novel Step-Up Power Converter Configuration for Solar Energy Application

2019 ◽  
Vol 25 (3) ◽  
pp. 50-55 ◽  
Author(s):  
Davood Ghaderi ◽  
Gokay Bayrak
Keyword(s):  
Renewable Energy ◽  
Duty Cycle ◽  
Renewable Energy Sources ◽  
High Gain ◽  
Power Converter ◽  
Boost Converter ◽  
Energy Sources ◽  
Switching Frequency ◽  
Voltage Gain ◽  
First Choice

Renewable Energy Sources (RES) including full cells, wind turbines, and photovoltaic panels, widely are spreading. Among all the renewable energy sources, solar power generation system tops the list. The first choice is the boost converter when the voltage step-up is the issue. But the most important subject is applying an efficient structure with high gain, cheap and quick controller circuit. Our proposed cascaded boost converter is one of such converters which consists of several cheap components such as diode, inductor, capacitor and power switch, which has same switching frequency and phase shift in comparison with conventional boost converters. In comparison with the classic cascaded boost converter, the voltage gain for the proposed structure is very high and by forming a preamplifier layer, for a duty cycle of 80 % by adding only two diodes, one inductor, and one capacitor for the second block, voltage gain is increased by 5 times compared to the classic boost converter. The proposed method provides the increased output voltage along with the duty cycle. The projected strategy has been verified with the help of Matlab/Simulink. Also, a hardware implementation of the proposed converter has been done around 200 W by applying a Jiangyin HR-200W-24V type solar panel.

A High Step-up DC-DC Converter Based on the Voltage Lift Technique for Renewable Energy Applications

2021 ◽  
Vol 13 (19) ◽  
pp. 11059
Author(s):  
Shahrukh Khan ◽  
Arshad Mahmood ◽  
Mohammad Zaid ◽  
Mohd Tariq ◽  
Chang-Hua Lin ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Common Ground ◽  
Closed Loop ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain

High gain DC-DC converters are getting popular due to the increased use of renewable energy sources (RESs). Common ground between the input and output, low voltage stress across power switches and high voltage gain at lower duty ratios are desirable features required in any high gain DC-DC converter. DC-DC converters are widely used in DC microgrids to supply power to meet local demands. In this work, a high step-up DC-DC converter is proposed based on the voltage lift (VL) technique using a single power switch. The proposed converter has a voltage gain greater than a traditional boost converter (TBC) and Traditional quadratic boost converter (TQBC). The effect of inductor parasitic resistances on the voltage gain of the converter is discussed. The losses occurring in various components are calculated using PLECS software. To confirm the performance of the converter, a hardware prototype of 200 W is developed in the laboratory. The simulation and hardware results are presented to determine the performance of the converter in both open-loop and closed-loop conditions. In closed-loop operation, a PI controller is used to maintain a constant output voltage when the load or input voltage is changed.

Seamless Control and Unified Dynamic Energy Management in a Renewable/Clean Energy Integrated Self-Reliant DC Microgrid

2021 ◽  
pp. 1083-1122
Author(s):  
Vulisi Narendra Kumar ◽  
Gayadhar Panda ◽  
Bonu Ramesh Naidu
Keyword(s):  
Renewable Energy ◽  
Renewable Energy Sources ◽  
Electrical Energy ◽  
Clean Energy ◽  
High Gain ◽  
Energy Sources ◽  
Dc Microgrid ◽  
Dc Power ◽  
Terminal Voltage ◽  
Operating Constraints

The growing demand for electrical energy calls for the assimilation of renewable energy sources to the main utility grid. Multiple renewable energy sources (RESs) like solar PV array, wind turbine, micro-hydro plant, etc. can be combined and controlled to form a microgrid. In spite of the availability of different microgrid topologies, DC microgrid largely facilitates the injection of DC power from various renewable energy sources into the stabilised DC power pool. The requirement for a minimal number of conversion stages, simple structure, economic operation, and numerous localised applications are driving factors for the DC microgrid technology. The mettle of the DC microgrid technology lies in choosing the appropriate microgrid participants for energy interchange and the suitable supervisory control to tap power from the microgrid partakers even after respecting their operating constraints. The use of high gain DC-DC converters is inevitable in DC microgrid due to the low terminal voltage levels of different RESs.

scholarly journals Modeling, Design Procedure and Control of a Low-Cost High-Gain Multi-Input Step-Up Converter

Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1424
Author(s):  
Edgardo Netzahuatl ◽  
Domingo Cortes ◽  
Marco A. Ramirez-Salinas ◽  
Jorge Resa ◽  
Leobardo Hernandez ◽  
...  
Keyword(s):  
Nonlinear Model ◽  
Low Cost ◽  
Renewable Energy Sources ◽  
Design Procedure ◽  
Input Voltage ◽  
High Gain ◽  
Grid Systems ◽  
Real Behavior ◽  
Different Characteristics ◽  
And Control

The use of several different sources to feed a load jointly is convenient in many applications, in particular those where two or more renewable energy sources are employed. These applications include energy harvesting, hybrid vehicles, and off-grid systems. A multi-input converter able to admit sources of different characteristics and select the output power of each source is necessary in such applications. Several topologies of multi-input converters have been proposed to this aim; however, most of them are controlled by simple strategies based on a small signal model of multi-input converters. In this work, a low cost high gain step-up multi-input converter is analyzed. A nonlinear model is derived. Using this model, a detailed design procedure is proposed. A 500 W converter prototype was constructed to confirm that the model predicted the real behavior of the converter. Using the nonlinear model, indirect voltage control of basic converters was extended to the multi-input converter. The obtained controller had a fast performance, and it was robust under load and input voltage variations. With the obtained model, the proposed design procedure, and the controller, a converter that was initially proposed for photovoltaic applications was enabled to be used in a broader range of applications. The herein exposed ideas for modeling, the design procedure, and control could be also applied to other multi-input converters.

scholarly journals Desain Sistem On-Grid Energi Terbarukan Skala Rumah Tangga Menggunakan Perangkat Lunak HOMER

2019 ◽  
Vol 1 (3) ◽  
pp. 174-180 ◽  
Author(s):  
Bandiyah Sri Aprillia ◽  
Desri Kristina Silalahi ◽  
Muhammad Agung Foury Rigoursyah
Keyword(s):  
Renewable Energy ◽  
Co2 Emissions ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Energy System ◽  
Payback Period ◽  
Energy Sources ◽  
Grid Systems ◽  
Diesel Generators ◽  
Carbon Dioxide Co2

Electricity demand increases along with an increasing population. Renewable energy power plants are experiencing an increase in their use. This increase occurred because the world's electricity needs are rising every year, so the development of renewable energy power plants continues. Indonesia's state-owned power plants supply electricity more from non-renewable energy sources than renewable energy sources. Therefore, there is a need for renewable energy sources that can supply electricity in Indonesia. This research discusses an efficient renewable energy system for residential and the total installation costs for on-grid systems in Bandung, Indonesia. The research method used is collecting solar radiation data, equipment specifications and other data needed and then optimized. The simulation model uses HOMER software. HOMER is used to determine the best technically estimated cost, payback period, and NPC. Based on the optimization results, the system configuration can supply the electricity load 45.5% of daily load consumption with a total NPC cost is 75,300,000 million with a payback period of 7 years. In addition, the on-grid system produces 1400 kg of carbon dioxide (CO2) emissions per year from diesel generators, lower than the CO2 emissions from systems that only comprise diesel generators reaching 114 tons per year.    

Seamless Control and Unified Dynamic Energy Management in a Renewable/Clean Energy Integrated Self-Reliant DC Microgrid

2022 ◽  
pp. 253-292
Author(s):  
Vulisi Narendra Kumar ◽  
Gayadhar Panda ◽  
Bonu Ramesh Naidu
Keyword(s):  
Renewable Energy ◽  
Renewable Energy Sources ◽  
Electrical Energy ◽  
Clean Energy ◽  
High Gain ◽  
Energy Sources ◽  
Dc Microgrid ◽  
Dc Power ◽  
Terminal Voltage ◽  
Operating Constraints

The growing demand for electrical energy calls for the assimilation of renewable energy sources to the main utility grid. Multiple renewable energy sources (RESs) like solar PV array, wind turbine, micro-hydro plant, etc. can be combined and controlled to form a microgrid. In spite of the availability of different microgrid topologies, DC microgrid largely facilitates the injection of DC power from various renewable energy sources into the stabilised DC power pool. The requirement for a minimal number of conversion stages, simple structure, economic operation, and numerous localised applications are driving factors for the DC microgrid technology. The mettle of the DC microgrid technology lies in choosing the appropriate microgrid participants for energy interchange and the suitable supervisory control to tap power from the microgrid partakers even after respecting their operating constraints. The use of high gain DC-DC converters is inevitable in DC microgrid due to the low terminal voltage levels of different RESs.

Sign in / Sign up

Export Citation Format

Share Document