scholarly journals Impact of Absorbers on the Shielding Effectiveness of Metallic Rooms with Apertures

Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 237
Author(s):  
Jong Hwa Kwon ◽  
Chang Hee Hyoung ◽  
Jung-Hwan Hwang ◽  
Hyun Ho Park
Keyword(s):  
Numerical Simulation ◽  
Electromagnetic Field ◽  
Resonant State ◽  
Standing Waves ◽  
Resonant Mode ◽  
Q Factor ◽  
Shielding Effectiveness ◽  
Frequency Range ◽  
Theoretical Formulation ◽  
Full Wave

An electromagnetic field penetrating through an aperture or slot of a metallic enclosure generates many standing-waves due to the resonance inside the metallic enclosure, which results in reduced shielding performance. This paper examines the effect of absorbent material (absorber) to improve shielding effectiveness (SE) of large metallic rooms with apertures or slots. First, a theoretical formulation to extract the Q-factor of an absorber with any shape is proposed. Using this, the contribution of the absorber to the SE improvement of a shielded room with different sized circular apertures was investigated. Second, the resonant mode density inside the shielded room was classified into non-resonant, under-moded, and over-moded states with an increase in frequency, and the effect of the absorber in each frequency range was examined. The analysis was conducted through numerical simulation using a commercial full-wave simulator and experimental measurement using a fabricated actual shielded room and commercial absorbers. The accuracy of the analysis results was verified through the comparison of simulated and measured results. The analysis results ensured that the absorber was not effective in improving the SE in the non-resonant state of the metallic room. It was also confirmed that the absorber was effective in improving the SE in the over-moded state of the metallic room where a severe standing-wave occurs. In addition, the SE improvement level differed depending on the location of the absorber in the room.

Tire Vibrations

1977 ◽  
Vol 5 (4) ◽  
pp. 202-225 ◽  
Author(s):  
G. R. Potts ◽  
C. A. Bell ◽  
L. T. Charek ◽  
T. K. Roy
Keyword(s):  
Natural Frequencies ◽  
Standing Waves ◽  
Resonant Mode ◽  
Mode Shapes ◽  
Resonant Vibrations ◽  
Resonant Frequencies ◽  
Radial Tire ◽  
Analysis Techniques ◽  
Thin Ring ◽  
Good Agreement

Abstract Natural frequencies and vibrating motions are determined in terms of the material and geometric properties of a radial tire modeled as a thin ring on an elastic foundation. Experimental checks of resonant frequencies show good agreement. Forced vibration solutions obtained are shown to consist of a superposition of resonant vibrations, each rotating around the tire at a rate depending on the mode number and the tire rotational speed. Theoretical rolling speeds that are upper bounds at which standing waves occur are determined and checked experimentally. Digital Fourier transform, transfer function, and modal analysis techniques used to determine the resonant mode shapes of a radial tire reveal that antiresonances are the primary transmitters of vibration to the tire axle.

scholarly journals Numerical treatment of the spatio-temporal electromagnetic beam-wave packet

2017 ◽  
Vol 68 (2) ◽  
pp. 109-116
Author(s):  
L’ubomír Šumichrast ◽  
Jaroslav Franek
Keyword(s):  
Numerical Simulation ◽  
Wave Equation ◽  
Wave Packet ◽  
Paraxial Approximation ◽  
Two Dimensional ◽  
Numerical Treatment ◽  
Beam Wave ◽  
Electromagnetic Beam ◽  
Full Wave ◽  
Spatio Temporal

Abstract Propagation of a two-dimensional spatio-temporal electromagnetic beam wave is analysed. In parabolic (paraxial) approximation the exact analytical results for a spatio-temporal Gaussian impulse can be obtained. For solution of the full wave equation the numerical simulation has to be used. The various facets of this simulation are discussed here.

A New Method to Concentrate Electromagnetic Field Within ROI Using a High Dielectric Material in 3T Body MRI

2013 ◽  
Author(s):  
Bu S. Park ◽  
Sunder S. Rajan ◽  
Leonardo M. Angelone
Keyword(s):  
Numerical Simulation ◽  
Electromagnetic Field ◽  
Human Body ◽  
Region Of Interest ◽  
Dielectric Materials ◽  
The Body ◽  
Human Body Model ◽  
Body Model ◽  
Simulation Results ◽  
High Dielectric

We present numerical simulation results showing that high dielectric materials (HDMs) when placed between the human body model and the body coil significantly alter the electromagnetic field inside the body. The numerical simulation results show that the electromagnetic field (E, B, and SAR) within a region of interest (ROI) is concentrated (increased). In addition, the average electromagnetic fields decreased significantly outside the region of interest. The calculation results using a human body model and HDM of Barium Strontium Titanate (BST) show that the mean local SAR was decreased by about 56% (i.e., 18.7 vs. 8.2 W/kg) within the body model.

Silicon Pillars as Resonators in an Acoustical Metamaterial

2014 ◽  
Author(s):  
Bernard Bonello ◽  
Rémi Marchal ◽  
Rayisa Moiseyenko ◽  
Yan Pennec ◽  
Bahram Djafari-Rouhani ◽  
...  
Keyword(s):  
Thin Plate ◽  
Lamb Waves ◽  
Mass Density ◽  
Resonant Mode ◽  
Ultrasonic Technique ◽  
Frequency Range ◽  
Negative Mass ◽  
Laser Ultrasonic ◽  
Compressional Mode ◽  
Bending Modes

We have investigated the propagation of Lamb waves in structures made of either an isolated resonant pillar or a set of pillars arranged in a line on a thin plate. The resonators as well as the plate are made of silicon. FEM computations show that two bending modes and one compressional mode are unambiguously identified in the frequency range of interest (0–10 MHz). We used a laser ultrasonic technique to map both the amplitude and the phase of the normal displacements on top of the pillars and at the surface of the sample. When the frequency is tuned to a resonant mode, either compressional or bending, the pillars vibrate 180° out-of-phase with respect to the Lamb waves, resulting in a negative modulus or negative mass density respectively.

Sign in / Sign up

Export Citation Format

Share Document