scholarly journals A New Fuzzy Logic Classifier Based on Multiscale Permutation Entropy and Its Application in Bearing Fault Diagnosis

Entropy ◽  
2019 ◽  
Vol 22 (1) ◽  
pp. 27 ◽  
Author(s):  
Wenhua Du ◽  
Xiaoming Guo ◽  
Zhijian Wang ◽  
Junyuan Wang ◽  
Mingrang Yu ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Mean Difference ◽  
Harmonic Mean ◽  
Permutation Entropy ◽  
Testing Sample ◽  
Training Stage ◽  
Fault Features ◽  
Testing Stage ◽  
Diagnosis Method ◽  
Representative Samples

The self-organizing fuzzy (SOF) logic classifier is an efficient and non-parametric classifier. Its classification process is divided into an offline training stage, an online training stage, and a testing stage. Representative samples of different categories are obtained through the first two stages, and these representative samples are called prototypes. However, in the testing stage, the classification of testing samples is completely dependent on the prototype with the maximum similarity, without considering the influence of other prototypes on the classification decision of testing samples. Aiming at the testing stage, this paper proposed a new SOF classifier based on the harmonic mean difference (HMDSOF). In the testing stage of HMDSOF, firstly, each prototype was sorted in descending order according to the similarity between each prototype in the same category and the testing sample. Secondly, multiple local mean vectors of the prototypes after sorting were calculated. Finally, the testing sample was classified into the category with the smallest harmonic mean difference. Based on the above new method, in this paper, the multiscale permutation entropy (MPE) was used to extract fault features, linear discriminant analysis (LDA) was used to reduce the dimension of fault features, and the proposed HMDSOF was further used to classify the features. At the end of this paper, the proposed fault diagnosis method was applied to the diagnosis examples of two groups of different rolling bearings. The results verify the superiority and generalization of the proposed fault diagnosis method.

scholarly journals Fault Diagnosis Method for Rotating Machinery Based on Hierarchical Amplitude-Aware Permutation Entropy and Pairwise Feature Proximity

2021 ◽  
Vol 2021 ◽  
pp. 1-18
Author(s):  
Ling Shu ◽  
Jinxing Shen ◽  
Xiaoming Liu
Keyword(s):  
Time Series ◽  
Fault Diagnosis ◽  
Low Frequency ◽  
Rotating Machinery ◽  
Permutation Entropy ◽  
Support Vector ◽  
Feature Vectors ◽  
Fault Features ◽  
Diagnosis Method ◽  
Frequency Features

With a view to solving the defect that multiscale amplitude-aware permutation entropy (MAAPE) can only quantify the low-frequency features of time series and ignore the high-frequency features which are equally important, a novel nonlinear time series feature extraction method, hierarchical amplitude-aware permutation entropy (HAAPE), is proposed. By constructing high and low-frequency operators, this method can extract the features of different frequency bands of time series simultaneously, so as to avoid the issue of information loss. In view of its advantages, HAAPE is introduced into the field of fault diagnosis to extract fault features from vibration signals of rotating machinery. Combined with the pairwise feature proximity (PWFP) feature selection method and gray wolf algorithm optimization support vector machine (GWO-SVM), a new intelligent fault diagnosis method for rotating machinery is proposed. In our method, firstly, HAPPE is adopted to extract the original high and low-frequency fault features of rotating machinery. After that, PWFP is used to sort the original features, and the important features are filtered to obtain low-dimensional sensitive feature vectors. Finally, the sensitive feature vectors are input into GWO-SVM for training and testing, so as to realize the fault identification of rotating machinery. The performance of the proposed method is verified using two data sets of bearing and gearbox. The results show that the proposed method enjoys obvious advantages over the existing methods, and the identification accuracy reaches 100%.

scholarly journals A New Bearing Fault Diagnosis Method Based on Refined Composite Multiscale Global Fuzzy Entropy and Self-Organizing Fuzzy Logic Classifier

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Zhang Ziying ◽  
Zhang Xi
Keyword(s):  
Fuzzy Logic ◽  
Fault Diagnosis ◽  
Online Training ◽  
Training Sample ◽  
Fuzzy Entropy ◽  
Testing Sample ◽  
Bearing Fault Diagnosis ◽  
Training Stage ◽  
Diagnosis Method ◽  
Sample Set

In this paper, a new feature extraction method called refined composite multiscale global fuzzy entropy (RCMGFE) is proposed. Based on the proposed RCMGFE and self-organizing fuzzy logic classifier (SOF), a new method for bearing fault diagnosis is proposed. Firstly, the fault features of the original bearing signal are extracted by using the proposed refined composite multiscale global fuzzy entropy, and the fault feature set of RCMGFE is constructed on this basis. Secondly, the extracted RCMGFE fault feature set is divided into an offline training sample set, an online training sample set, and a testing sample set. The offline training sample set and the online training sample set are, respectively, input into the offline training stage and the online training stage of the SOF for selecting representative samples and constructing fuzzy rules. Then, the testing sample set is input to the testing stage of the SOF for classification. Finally, the data of drive end bearing and fan end bearing provided by Case Western Reserve University are used to verify the validity of the proposed fault diagnosis method. The experimental results show that, compared with other methods, the proposed fault diagnosis method has a higher classification effect.

The Application of Improved SVM in Mixed Circuit

2012 ◽  
Vol 224 ◽  
pp. 493-496 ◽  
Author(s):  
Huai Long Wang ◽  
Qiang Pan ◽  
Hong Liu
Keyword(s):  
Wavelet Transform ◽  
Fault Diagnosis ◽  
Small Samples ◽  
Lifting Wavelet Transform ◽  
Fault Features ◽  
Diagnosis Method ◽  
Lifting Wavelet ◽  
Current Characteristics ◽  
Mixed Circuit ◽  
Better Than

In order to improve the speed and the rate of fault diagnosis in mixed circuit, this paper introduces a new fault diagnosis method. Through extracting fault features of current characteristics effectively and applying to Improved SVM, the ability of pattern recognition will be better than the traditional BP Neural Network and Single SVM, especially in small samples or non-linear cases. Meanwhile, this paper presents the lifting wavelet transform in order to obtain the feature information accurately. The accuracy of fault diagnosis can greatly enhance by discussing the Improved SVM combined with lifting wavelet transform in a specific monostable trigger. That points out a new direction for the fault diagnosis of mixed circuit.

scholarly journals An Intelligent Fault Diagnosis Method for Reciprocating Compressors Based on LMD and SDAE

Sensors ◽  
2019 ◽  
Vol 19 (5) ◽  
pp. 1041 ◽  
Author(s):  
Yang Liu ◽  
Lixiang Duan ◽  
Zhuang Yuan ◽  
Ning Wang ◽  
Jianping Zhao
Keyword(s):  
Fault Diagnosis ◽  
Health Management ◽  
Vibration Signal ◽  
Intelligent Fault Diagnosis ◽  
Traditional Methods ◽  
Learning Abilities ◽  
Fault Features ◽  
Correlation Criterion ◽  
Long Time ◽  
Diagnosis Method

The effective fault diagnosis in the prognostic and health management of reciprocating compressors has been a research hotspot for a long time. The vibration signal of reciprocating compressors is nonlinear and non-stationary. However, the traditional methods applied to processing such signals have three issues, including separating the useful frequency bands from overlapped signals, extracting fault features with strong subjectivity, and processing the massive data with limited learning abilities. To address the above issues, this paper, which is based on the idea of deep learning, proposed an intelligent fault diagnosis method combining Local Mean Decomposition (LMD) and the Stack Denoising Autoencoder (SDAE). The vibration signal is firstly decomposed by LMD and reconstructed based on the cross-correlation criterion. The virtual noise channel is constructed to reduce the noise of the vibration signal. Then, the de-noised signal is input into the trained SDAE model to learn the fault features adaptively. Finally, the conditions of the reciprocating compressor valve are classified by the proposed method. The results show that classification accuracy is 92.72% under the condition of a low signal-noise ratio, which is 5 percentage points higher than that of the traditional methods. This shows the effectiveness and robustness of the proposed method.

scholarly journals Application of a Novel Adaptive Med Fault Diagnosis Method in Gearboxes

Entropy ◽  
2019 ◽  
Vol 21 (11) ◽  
pp. 1106
Author(s):  
Wenhua Du ◽  
Xiaoming Guo ◽  
Xiaofeng Han ◽  
Junyuan Wang ◽  
Jie Zhou ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Fitness Function ◽  
Vibration Signal ◽  
Ar Model ◽  
Fluctuation Analysis ◽  
Minimum Entropy ◽  
Fault Features ◽  
Filter Size ◽  
Diagnosis Method ◽  
Reduction Effect

Minimum entropy deconvolution (MED) is not effective in extracting fault features in strong noise environments, which can easily lead to misdiagnosis. Moreover, the noise reduction effect of MED is affected by the size of the filter. In the face of different vibration signals, the size of the filter is not adaptive. In order to improve the efficiency of MED fault feature extraction, this paper proposes a firefly optimization algorithm (FA) to improve the MED fault diagnosis method. Firstly, the original vibration signal is stratified by white noise-assisted singular spectral decomposition (SSD), and the stratified signal components are divided into residual signal components and noisy signal components by a detrended fluctuation analysis (DFA) algorithm. Then, the noisy components are preprocessed by an autoregressive (AR) model. Secondly, the envelope spectral entropy is proposed as the fitness function of the FA algorithm, and the filter size of MED is optimized by the FA algorithm. Finally, the preprocessed signal is denoised and the pulse enhanced with the proposed adaptive MED. The new method is validated by simulation experiments and practical engineering cases. The application results show that this method improves the shortcomings of MED and can extract fault features more effectively than the traditional MED method.

scholarly journals A New Intelligent Fault Diagnosis Method of Rotating Machinery under Varying-Speed Conditions Using Infrared Thermography

Complexity ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Yongbo Li ◽  
Xianzhi Wang ◽  
Shubin Si ◽  
Xiaoqiang Du
Keyword(s):  
Support Vector Machine ◽  
Fault Diagnosis ◽  
Infrared Thermography ◽  
Rotating Machinery ◽  
Support Vector ◽  
Intelligent Fault Diagnosis ◽  
Fault Features ◽  
Diagnosis Method ◽  
Systematic Framework ◽  
Machinery Fault Diagnosis

A novel systematic framework, infrared thermography- (IRT-) based method, for rotating machinery fault diagnosis under nonstationary running conditions is presented in this paper. In this framework, IRT technique is first applied to obtain the thermograph. Then, the fault features are extracted using bag-of-visual-word (BoVW) from the IRT images. In the end, support vector machine (SVM) is utilized to automatically identify the fault patterns of rotating machinery. The effectiveness of proposed method is evaluated using lab experimental signal of rotating machinery. The diagnosis results show that the IRT-based method has certain advantages in classification rotating machinery faults under nonstationary running conditions compared with the traditional vibration-based method.

scholarly journals A Novel Bearing Fault Diagnosis Method Based on GL-mRMR-SVM

Processes ◽  
2020 ◽  
Vol 8 (7) ◽  
pp. 784
Author(s):  
Xianghong Tang ◽  
Qiang He ◽  
Xin Gu ◽  
Chuanjiang Li ◽  
Huan Zhang ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Feature Fusion ◽  
Global Features ◽  
Bearing Fault ◽  
Bearing Fault Diagnosis ◽  
Fault Recognition ◽  
Fault Features ◽  
Svm Model ◽  
Diagnosis Method ◽  
The Time Domain

A convolutional neural network (CNN) has been used to successfully realize end-to-end bearing fault diagnosis due to its powerful feature extraction ability. However, the CNN is prone to focus on local information, ignoring the relationship between the whole and the part of the signal due to its unique structure. In addition, it extracts some fault features with poor robustness under noisy environment. A novel diagnosis model based on feature fusion and feature selection, GL-mRMR-SVM, is proposed to address this problem in this paper. First, the model combines the global features in the time-domain and frequency-domain of the raw data with the local features extracted by CNN to make full use of the signal information and overcome the weakness of traditional CNNs neglecting the overall signal. Then, the max-relevance min-redundancy (mRMR) algorithm is used to automatically extract the discriminative features from the fused features without any prior knowledge. Finally, the extracted discriminative features are input into the SVM for training and output the fault recognition results. The proposed GL-mRMR-SVM model was evaluated through experiments on bearing data of Case Western Reserve University (CWRU) and CUT-2 platform. The experimental results show that the proposed method is more effective than other intelligent diagnosis methods.

scholarly journals Design of Fault Diagnosis Algorithm for Electromechanical System Based on Artificial Intelligence

2021 ◽  
Vol 2050 (1) ◽  
pp. 012011
Author(s):  
Fuyou Zhao ◽  
Mingying Huo ◽  
Naiming Qi ◽  
Lianfeng Li ◽  
Weiwei Cui
Keyword(s):  
Neural Network ◽  
Artificial Intelligence ◽  
Deep Learning ◽  
Fault Diagnosis ◽  
Data Sets ◽  
Learning Technology ◽  
Electrical System ◽  
Fault Recognition ◽  
Fault Features ◽  
Diagnosis Method

Abstract A relatively perfect system for the fault diagnosis of mechanical and electrical products has been formed through decades of development. Nevertheless, the traditional fault diagnosis methods fail to cope with the gradual huge mechanical and electrical system. As a result, the advantages of fault diagnosis mode driven by data are increasingly prominent. Meanwhile, the effect of fault diagnosis has exceeded the traditional fault diagnosis methods in many fields. Through the use of the deep learning technology based on artificial intelligence, it carries out mapping and fitting. By fully taking advantages of neural network, it can effectively obtain the accurate classification of fault data. A fault diagnosis method based on the fault data of mechanical and electrical system is designed in this thesis. When it comes to the basic process, it is to take data sets for different mechanical and electrical products. Through the use of feature engineering method, it extracts the fault features of data. Through the use of deep learning technology, it carries out the intelligent diagnosis. According to the experimental results, it indicates that the fault diagnosis method based on deep learning technology can distinguish a variety of fault modes in mechanical and electrical system in an effective way. What’s more, good classification results in fault recognition have been achieved by a variety of deep convolutional neural network structures, so the feasibility of the method is further verified.

Sign in / Sign up

Export Citation Format

Share Document