scholarly journals Effect of Interdendritic Precipitations on the Mechanical Properties of GBF or EMS Processed Al-Zn-Mg-Cu Alloys

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1162
Author(s):  
Sangeun Park ◽  
Saif Haider Kayani ◽  
Hyungrae Kim ◽  
Im Doo Jung ◽  
N.S. Reddy ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Backscatter Diffraction ◽  
Tensile Fracture ◽  
Cu Alloys ◽  
Cell Structures ◽  
Transmission Electron ◽  
Heat Treated ◽  
Electron Backscatter ◽  
Gas Bubbling ◽  
Backscatter Diffraction

The effects of nanoprecipitations on the mechanical properties of Al-Zn-Mg-Cu alloys after GBF (gas bubbling filtration) and EMS (electromagnetic stirring) casting were investigated. Dendritic cell structures were formed after GBF processing, while globular dendritic structures were nucleated after EMS processing. Equiaxed cell sizes were smaller in the EMS-processed specimens compared to the GBF-processed specimens, confirmed by EBSD (electron backscatter diffraction) analysis. Nanoprecipitations of η′ phases inside of dendrites were observed by TEM (transmission electron microscope), and other Fe-bearing compounds were located in the dendritic boundaries. The yield strength of the T4 and T6 heat-treated specimens was close to 400 MPa and 500 MPa, respectively. Fractographic analysis was performed to investigate the effect of precipitations on tensile fracture.

Where are the geometrically necessary dislocations accommodating small imprints?

2009 ◽  
Vol 24 (3) ◽  
pp. 647-651 ◽  
Author(s):  
M. Rester ◽  
C. Motz ◽  
R. Pippan
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Twin Boundary ◽  
Crystal Orientation ◽  
Electron Backscatter Diffraction ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Copper Single Crystals ◽  
Backscatter Diffraction ◽  
Small Misorientation

Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analyses of small indentations in copper single crystals exhibit only slight changes of the crystal orientation in the surroundings of the imprints. Far-reaching dislocations might be the reason for these small misorientation changes. Using EBSD and TEM technique, this work makes an attempt to visualize the far-propagating dislocations by introducing a twin boundary in the vicinity of small indentations. Because dislocations piled up at the twin boundary produce a misorientation gradient, the otherwise far-propagating dislocations can be detected.

Heteroepitaxy of Ge on Cube-Textured Ni(001) Foils Through CaF2 Buffer Layer

MRS Advances ◽  
2016 ◽  
Vol 1 (43) ◽  
pp. 2947-2952
Author(s):  
L. Chen ◽  
Z.-H. Lu ◽  
T.-M. Lu ◽  
I. Bhat ◽  
S.B. Zhang ◽  
...  
Keyword(s):  
Buffer Layer ◽  
High Efficiency ◽  
Electron Backscatter Diffraction ◽  
Low Cost ◽  
High Quality ◽  
Tem Analysis ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Image Position ◽  
Backscatter Diffraction

ABSTRACTEpitaxial Ge films are useful as a substrate for high-efficiency solar cell applications. It is possible to grow epitaxial Ge films on low cost, cube textured Ni(001) sheets using CaF2(001) as a buffer layer. Transmission electron microscopy (TEM) analysis indicates that the CaF2(001) lattice has a 45o in-plane rotation relative to the Ni(001) lattice. The in-plane epitaxy relationships are CaF2[110]//Ni[100] and CaF2[$\bar 1$10]//Ni[010]. Energy dispersive spectroscopy (EDS) shows a sharp interface between Ge/CaF2 as well as between CaF2/Ni. Electron backscatter diffraction (EBSD) shows that the Ge(001) film has a large grain size (∼50 μm) with small angle grain boundaries (< 8o). The epitaxial Ge thin film has the potential to be used as a substrate to grow high quality III-V and II-VI semiconductors for optoelectronic applications.

scholarly journals Coupling Automated Electron Backscatter Diffraction with Transmission Electron and Atomic Force Microscopies

2000 ◽  
Vol 6 (S2) ◽  
pp. 940-941
Author(s):  
A.J. Schwartz ◽  
M. Kumar ◽  
P.J. Bedrossian ◽  
W.E. King
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Thermomechanical Processing ◽  
Electron Backscatter Diffraction ◽  
Grain Boundary Character Distribution ◽  
Atomic Force ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Network Engineering ◽  
Backscatter Diffraction

Grain boundary network engineering is an emerging field that encompasses the concept that modifications to conventional thermomechanical processing can result in improved properties through the disruption of the random grain boundary network. Various researchers have reported a correlation between the grain boundary character distribution (defined as the fractions of “special” and “random” grain boundaries) and dramatic improvements in properties such as corrosion and stress corrosion cracking, creep, etc. While much early work in the field emphasized property improvements, the opportunity now exists to elucidate the underlying materials science of grain boundary network engineering. Recent investigations at LLNL have coupled automated electron backscatter diffraction (EBSD) with transmission electron microscopy (TEM)5 and atomic force microscopy (AFM) to elucidate these fundamental mechanisms.An example of the coupling of TEM and EBSD is given in Figures 1-3. The EBSD image in Figure 1 reveals “segmentation” of boundaries from special to random and random to special and low angle grain boundaries in some grains, but not others, resulting from the 15% compression of an Inconel 600 polycrystal.

scholarly journals Transmission Electron Backscatter Diffraction (tEBSD) analysis of Au Thin Films

2015 ◽  
Vol 21 (S3) ◽  
pp. 1671-1672
Author(s):  
Eliot Estrine ◽  
Nicholas Seaton ◽  
Prabesh Dulal ◽  
Bethanie Stadler
Keyword(s):  
Thin Films ◽  
Electron Backscatter Diffraction ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Au Thin Films ◽  
Backscatter Diffraction

Formation of Nanoporous Gold Studied by Transmission Electron Backscatter Diffraction

2015 ◽  
Vol 21 (6) ◽  
pp. 1387-1397 ◽  
Author(s):  
Leo T.H. de Jeer ◽  
Diego Ribas Gomes ◽  
Jorrit E. Nijholt ◽  
Rik van Bremen ◽  
Václav Ocelík ◽  
...  
Keyword(s):  
Crystallographic Texture ◽  
Manufacturing Process ◽  
Electron Backscatter Diffraction ◽  
Nanoporous Materials ◽  
Nanoporous Gold ◽  
Grain Structure ◽  
Misorientation Distribution ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Backscatter Diffraction

AbstractTransmission electron backscatter diffraction (t-EBSD) was used to investigate the effect of dealloying on the microstructure of 140-nm thin gold foils. Statistical and local comparisons of the microstructure between the nonetched and nanoporous gold foils were made. Analyses of crystallographic texture, misorientation distribution, and grain structure clearly prove that during the dealloying manufacturing process of nanoporous materials the crystallographic texture is enhanced significantly with a clear decrease of internal strain, whereas maintaining the grain structure.

scholarly journals High Strain Rate Properties of Various Forms of Ti6Al4V(ELI) Produced by Direct Metal Laser Sintering

2021 ◽  
Vol 11 (17) ◽  
pp. 8005
Author(s):  
Amos Muiruri ◽  
Maina Maringa ◽  
Willie du Preez
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Electron Backscatter Diffraction ◽  
Dynamic Strength ◽  
Strain Rates ◽  
Direct Metal Laser Sintering ◽  
Heat Treated ◽  
Electron Backscatter ◽  
Backscatter Diffraction

For analysis of engineering structural materials to withstand harsh environmental conditions, accurate knowledge of properties such as flow stress and failure over conditions of high strain rate and temperature plays an essential role. Such properties of additively manufactured Ti6Al4V(ELI) are not adequately studied. This paper documents an investigation of the high strain rate and temperature properties of different forms of heat-treated Ti6Al4V(ELI) samples produced by the direct metal laser sintering (DMLS). The microstructure and texture of the heat-treated samples were analysed using a scanning electron microscope (SEM) equipped with an electron backscatter diffraction detector for electron backscatter diffraction (EBSD) analysis. The split Hopkinson pressure bar (SHPB) equipment was used to carry out tests at strain rates of 750, 1500 and 2450 s−1, and temperatures of 25, 200 and 500 °C. The heat-treated samples of DMLS Ti6Al4V(ELI) alloys tested here were found to be sensitive to strain rate and temperature. At most strain rates and temperatures, the samples with finer microstructure exhibited higher dynamic strength and lower strain, while the dynamic strength and strain were lower and higher, respectively, for samples with coarse microstructure. The cut surfaces of the samples tested were characterised by a network of well-formed adiabatic shear bands (ASBs) with cracks propagating along them. The thickness of these ASBs varied with the strain rate, temperature, and various alloy forms.

scholarly journals Dislocation Creep of Olivine and Amphibole in Amphibole Peridotites from Åheim, Norway

Minerals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1018
Author(s):  
Sejin Jung ◽  
Takafumi Yamamoto ◽  
Jun-ichi Ando ◽  
Haemyeong Jung
Keyword(s):  
Electron Microscopy ◽  
Slip System ◽  
Electron Backscatter Diffraction ◽  
Microstructural Analysis ◽  
Dislocation Creep ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Different Types ◽  
Localized Shear Deformation ◽  
Backscatter Diffraction

Amphibole peridotite samples from Åheim, Norway, were analyzed to understand the deformation mechanism and microstructural evolution of olivine and amphibole through the Scandian Orogeny and subsequent exhumation process. Three Åheim amphibole peridotite samples were selected for detailed microstructural analysis. The Åheim amphibole peridotites exhibit porphyroclastic texture, abundant subgrain boundaries in olivine, and the evidence of localized shear deformation in the tremolite-rich layer. Two different types of olivine lattice preferred orientations (LPOs) were observed: B- and A-type LPOs. Electron backscatter diffraction (EBSD) mapping and transmission electron microscopy (TEM) observations revealed that most subgrain boundaries in olivine consist of dislocations with a (001)[100] slip system. The subgrain boundaries in olivine may have resulted from the deformation of olivine with moderate water content. In addition, TEM observations using a thickness-fringe method showed that the free dislocations of olivine with the (010)[100] slip system were dominant in the peridotites. Our data suggest that the subgrain boundaries and free dislocations in olivine represent a product of later-stage deformation associated with the exhumation process. EBSD mapping of the tremolite-rich layer revealed intracrystalline plasticity in amphibole, which can be interpreted as the activation of the (100)[001] slip system.

Sign in / Sign up

Export Citation Format

Share Document