scholarly journals Photocatalytic Antibacterial Effectiveness of Cu-Doped TiO2 Thin Film Prepared via the Peroxo Sol-Gel Method

Catalysts ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 352 ◽  
Author(s):  
Benjawan Moongraksathum ◽  
Jun-Ya Shang ◽  
Yu-Wen Chen
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Gel Method ◽  
Doped Tio2 ◽  
X Ray ◽  
Photocatalytic Activities

Cu-doped titanium dioxide thin films (Cu/TiO2) were prepared on glass substrate via peroxo sol-gel method and dip-coating process with no subsequent calcination process for the degradation of organic dye and use as an antibacterial agent. The as-prepared materials were characterised using transmission electron microscopy (TEM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). For photocatalytic degradation of methylene blue in water, the samples were subjected to Ultraviolet C (UVC) and visible light irradiation. Degraded methylene blue concentration was measured using UV-Vis spectrophotometer. The antibacterial activities of the samples were tested against the gram-negative bacteria Escherichia coli (ATCC25922). Copper species were present in the form of CuO on the surface of modified TiO2 particles, which was confirmed using TEM and XPS. The optimal observed Cu/TiO2 weight ratio of 0.5 represents the highest photocatalytic activities under both UVC and visible light irradiation. Moreover, the same composition remarkably exhibited high antibacterial effectiveness against E. coli after illumination with ultraviolet A. The presence of CuO on TiO2 significantly enhanced photocatalytic activities. Therefore, active Cu-doped TiO2 can be used as a multipurpose coating material.

scholarly journals Visible-enhanced photocatalytic performance of CuWO4/WO3 hetero-structures: incorporation of plasmonic Ag nanostructures

2018 ◽  
Vol 42 (13) ◽  
pp. 11109-11116 ◽  
Author(s):  
R. Salimi ◽  
A. A. Sabbagh Alvani ◽  
N. Naseri ◽  
S. F. Du ◽  
D. Poelman
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Light Irradiation ◽  
Photo Degradation ◽  
Gel Method ◽  
Sol Gel Method

A new plasmonic Ag hybridized CuWO4/WO3 heterostructured nanocomposite was successfully synthesized via a ligand-assisted sol gel method and the photocatalytic activity was evaluated by photo-degradation of methylene blue (MB) under visible light irradiation.

scholarly journals Photocatalytic conversion of CO2 into methanol: Significant enhancement of the methanol yield over Bi2S3/CdS photocatalyst

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
M.Rahim Uddin ◽  
Maksudur R. Khan ◽  
M. Wasikur Rahman ◽  
Chin Kui Cheng ◽  
Abu Yousuf
Keyword(s):  
Carbon Dioxide ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Significant Enhancement ◽  
Gel Method ◽  
Sol Gel Method ◽  
Photocatalytic Activities ◽  
Carbon Dioxide Co2

The present work is a significant approach to explore the photo-conversion of carbon dioxide (CO2) into methanol on Bi2S3/Cds photocatalyst under visible light irradiation. In this perspective, Bi2S3 nanoparticles have been successfully synthesized via corresponding salt and thiourea assisted sol-gel method. An innovative hetero-system Bi2S3/CdS has been proposed to achieve methanol photo evolution and its photocatalytic activities have been investigated.

scholarly journals Development of Smart Composites Based on Doped-TiO2 Nanoparticles with Visible Light Anticancer Properties

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2589 ◽  
Author(s):  
Evdokia Galata ◽  
Eleni A. Georgakopoulou ◽  
Maria-Emmanouela Kassalia ◽  
Nefeli Papadopoulou-Fermeli ◽  
Evangelia A. Pavlatou
Keyword(s):  
Visible Light ◽  
Tio2 Nanoparticles ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Ultra Violet ◽  
Light Irradiation ◽  
Composite Particles ◽  
Doped Tio2 ◽  
X Ray ◽  
Anticancer Properties

In this study, the synthesis of smart, polymerically embedded titanium dioxide (TiO2) nanoparticles aimed to exhibit photo-induced anticancer properties under visible light irradiation is investigated. The TiO2 nanoparticles were prepared by utilizing the sol gel method with different dopants, including nitrogen (N-doped), iron (Fe-doped), and nitrogen and iron (Fe,N-doped). The dopants were embedded in an interpenetrating (IP) network microgel synthesized by stimuli responsive poly (N-Isopropylacrylamide-co-polyacrylicacid)–pNipam-co-PAA forming composite particles. All the types of produced particles were characterized by X-ray powder diffraction, micro-Raman, Fourier-transform infrared, X-ray photoelectron, ultra-violet-visible spectroscopy, Field Emission Scanning Electron, Transmission Electron microscopy, and Dynamic Light Scattering techniques. The experimental findings indicate that the doped TiO2 nanoparticles were successfully embedded in the microgel. The N-doped TiO2 nano-powders and composite particles exhibit the best photocatalytic degradation of the pollutant methylene blue under visible light irradiation. Similarly, the highly malignant MDA-MB-231 breast cancer epithelial cells were susceptible to the inhibition of cell proliferation at visible light, especially in the presence of N-doped powders and composites, compared to the non-metastatic MCF-7 cells, which were not affected.

scholarly journals Cu-Doped TiO2: Visible Light Assisted Photocatalytic Antimicrobial Activity

2018 ◽  
Vol 8 (11) ◽  
pp. 2067 ◽  
Author(s):  
Snehamol Mathew ◽  
Priyanka Ganguly ◽  
Stephen Rhatigan ◽  
Vignesh Kumaravel ◽  
Ciara Byrne ◽  
...  
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Density Functional ◽  
Anatase Phase ◽  
Sol Gel ◽  
Light Irradiation ◽  
Health Concern ◽  
Bacterial Inactivation ◽  
Doped Tio2 ◽  
X Ray

Surface contamination by microbes is a major public health concern. A damp environment is one of potential sources for microbe proliferation. Smart photocatalytic coatings on building surfaces using semiconductors like titania (TiO2) can effectively curb this growing threat. Metal-doped titania in anatase phase has been proven as a promising candidate for energy and environmental applications. In this present work, the antimicrobial efficacy of copper (Cu)-doped TiO2 (Cu-TiO2) was evaluated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) under visible light irradiation. Doping of a minute fraction of Cu (0.5 mol %) in TiO2 was carried out via sol-gel technique. Cu-TiO2 further calcined at various temperatures (in the range of 500–700 °C) to evaluate the thermal stability of TiO2 anatase phase. The physico-chemical properties of the samples were characterized through X-ray diffraction (XRD), Raman spectroscopy, X-ray photo-electron spectroscopy (XPS) and UV–visible spectroscopy techniques. XRD results revealed that the anatase phase of TiO2 was maintained well, up to 650 °C, by the Cu dopant. UV–vis results suggested that the visible light absorption property of Cu-TiO2 was enhanced and the band gap is reduced to 2.8 eV. Density functional theory (DFT) studies emphasize the introduction of Cu+ and Cu2+ ions by replacing Ti4+ ions in the TiO2 lattice, creating oxygen vacancies. These further promoted the photocatalytic efficiency. A significantly high bacterial inactivation (99.9999%) was attained in 30 min of visible light irradiation by Cu-TiO2.

scholarly journals Enhanced Photoactivity of Fe + N Codoped Anatase-RutileTiO2Nanowire Film under Visible Light Irradiation

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Kewei Li ◽  
Haiying Wang ◽  
Chunxu Pan ◽  
Jianhong Wei ◽  
Rui Xiong ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Synergistic Effects ◽  
Anatase Phase ◽  
Light Irradiation ◽  
Codoped Sample ◽  
X Ray ◽  
Photocatalytic Activities

Rutile-anatase phase mixedFe+Ncodoped TiO2nanowires were designed and prepared by a two-step anodic oxidation method. The results of X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy confirm that the preparedFe+Ncodoped TiO2nanowires exhibit intimately contacted anatase-rutile heterostructure with the rutile content of 21.89%. The X-ray photoelectron spectroscopy measurements show that nitrogen and iron atoms are incorporated into the titania oxide lattice, and the UV-visible absorption spectra show that the codoping of iron and nitrogen atoms could extend the absorption to visible light region. The photocatalytic activities of all the samples were evaluated by photocatalytic degradation of methylene blue under visible light irradiation. TheFe+Ncodoped sample achieves the best response to visible light and the highest photocatalytic activities. The enhancement of photocatalytic activity forFe+Ncodoped sample should be ascribed to the synergistic effects of codoped nitrogen and iron ions and the anatase-rutile heterostructure.

scholarly journals Photocatalytic Properties of Amorphous N-doped TiO2 Photocatalyst under Visible Light Irradiation

Catalysts ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1010
Author(s):  
Kyong-Hwan Chung ◽  
Byung-Joo Kim ◽  
Young-Kwon Park ◽  
Sang-Chai Kim ◽  
Sang-Chul Jung
Keyword(s):  
Heat Treatment ◽  
Low Temperature ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Sol Gel ◽  
Light Irradiation ◽  
Photocatalytic Decomposition ◽  
Doped Tio2 ◽  
Plasma Irradiation ◽  
Photocatalytic Activities

Amorphous TiO2 doped with N was characterized by its photocatalytic activity under visible light irradiation. The amorphous N-doped TiO2 was prepared by the sol-gel method through heat treatment at a low temperature. The photocatalyst showing activity in visible light despite heat treatment at low temperature can be applied to plastics and has excellent utility. The N-doped TiO2 appeared amorphous when heat-treated at 130 °C. It was converted into an anatase-type N-doped TiO2 when this was calcined at 500 °C. The photocatalyst showed photocatalytic activities in the photocatalytic decomposition of formaldehyde and methylene blue under visible light irradiation. The photocatalyst exhibited a higher rate of hydrogen production than that of TiO2 in photocatalytic decomposition of water under liquid-phase plasma irradiation. The bandgap of the amorphous N-doped TiO2 measured by investigation of optical properties was 2.4 eV. The lower bandgap induced the photocatalytic activities under visible light irradiation.

scholarly journals Visible Light Induced Photodegradation of Methylene Blue in Sodium Doped Bismuth Barium Ferrite Nanoparticle Synthesized by Sol-gel Method

2018 ◽  
Vol 5 (2) ◽  
pp. 120-126 ◽  
Author(s):  
Abdurrashid Haruna ◽  
Ibrahim Abdulkadir ◽  
Suleiman Ola Idris
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Light Irradiation ◽  
Blue Dye ◽  
Gel Method ◽  
Sol Gel Method

Perovskite-like BiFeO3 nanoparticles doped with barium and sodium ions were synthesized via the citric acid route by the sol-gel method. The as-prepared Bi0.65Na0.2Ba0.15FeO3 nanopowders were divided into three equal portions and separately annealed at various annealing temperatures of 600, 700 and 800°C. The powders were characterized using X-ray diffraction (XRD) and crystallized with a rhombohedral R3c space group. Scanning electron microscopy was used to determine the morphology of the crystal and Fourier transform infrared spectroscopy was conducted at room temperature to determine the phase purity and the B-site formation in the perovskite structure. The UV-vis diffuse reflectance spectroscopy of all the materials was investigated, showing strong photoabsorption (λ > 420 nm). The doping effect of BiFeO3 enhanced photocatalytic activity while it significantly reduced the energy bandgap to 2.05 eV (for BNBFO at 800°C) which showed strong visible light absorption. The photocatalytic activity of Bi0.65Na0.2Ba0.15FeO3 nanomaterials was tested by monitoring the degradation rate of methylene blue dye pollutant under visible light irradiation in aqueous solution. All powders showed photoactivity after 2 hours of visible light irradiation. The annealing temperature greatly affected the methylene blue degradation, showing the efficiencies of 57, 67 and 75 % for BNBFO at 600, 700 and 800°C, respectively. Kinetic studies were carried out and the rate constants of 6.70 x 10-3, 8.90 x 10-3 and 1.05 x 10-2 min-1 were obtained for powders annealed at 600, 700 and 800°C, respectively. The photocatalytic mechanism of the degradation process was proposed in this study.

Cu Doped TiO2: Visible Light Assisted Photocatalytic Antimicrobial Activity and High Temperature Anatase Stability

2018 ◽  
Author(s):  
Snehamol Mathew ◽  
Priyanka Ganguly ◽  
Stephen Rhatigan ◽  
Vignesh Kumaravel ◽  
Ciara Byrne ◽  
...  
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Density Functional ◽  
Anatase Phase ◽  
Sol Gel ◽  
Chemical Properties ◽  
Light Irradiation ◽  
Health Concern ◽  
Bacterial Inactivation ◽  
X Ray

Indoor surface contamination by microbes is a major public health concern. A damp environment is one potential sources for microbe proliferation. Smart photocatalytic coatings on building surfaces using semiconductors like titania (TiO<sub>2</sub>) can effectively curb this growing threat.<b> </b>Metal-doped titania in anatase phase has been proved as a promising candidate for energy and environmental applications. In this present work, the antimicrobial efficacy of copper (Cu) doped TiO<sub>2 </sub>(Cu-TiO<sub>2</sub>) was evaluated against <i>Escherichia coli</i> (Gram-negative) and <i>Staphylococcus aureus</i> (Gram-positive) under visible light irradiation. Doping of a minute fraction of Cu (0.5 mol %) in TiO<sub>2 </sub>was carried out <i>via</i> sol-gel technique. Cu-TiO<sub>2</sub> further calcined at various temperatures (in the range of 500 °C – 700 °C) to evaluate the thermal stability of TiO<sub>2</sub> anatase phase. The physico-chemical properties of the samples were characterised through X-ray diffraction (XRD), Raman spectroscopy, X-ray photo-electron spectroscopy (XPS) and UV-visible spectroscopy techniques. XRD results revealed that the anatase phase of TiO<sub>2</sub> was maintained well, up to 650 °C, by the Cu dopant. UV-DRS results suggested that the visible light absorption property of Cu-TiO<sub>2 </sub>was enhanced and the band gap is reduced to 2.8 eV. Density functional theory (DFT) studies emphasises the introduction of Cu<sup>+</sup> and Cu<sup>2+</sup> ions by replacing Ti<sup>4+</sup> ions in the TiO<sub>2</sub> lattice, creating oxygen vacancies. These further promoted the photocatalytic efficiency. A significantly high bacterial inactivation (99.9%) was attained in 30 mins of visible light irradiation by Cu-TiO<sub>2</sub>.

Photocatalytic Degradation of Methylene Blue over Co-Ag3VO4 under Visible Light Irradiation

2011 ◽  
Vol 335-336 ◽  
pp. 1385-1390 ◽  
Author(s):  
Shuo Wiei Zhao ◽  
Hui Xu ◽  
Hua Ming Li ◽  
Yuan Guo Xu
Keyword(s):  
Methylene Blue ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Visible Light Irradiation ◽  
Absorption Edge ◽  
Diffuse Reflectance Spectroscopy ◽  
Dye Degradation ◽  
Light Irradiation ◽  
Experimental Conditions ◽  
X Ray

In order to improve the photocatalytic activity, Co was successfully loaded into Ag3VO4 by using impregnation process. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS) and diffuse reflectance spectroscopy (DRS). The XRD and SEM–EDS analyses revealed that Co ion was dispersed on Ag3VO4. The DRS results indicated that the absorption edge of the Co–Ag3VO4 catalyst shifted to longer wavelength. The enhanced photocatalytic activity of Co–Ag3VO4 for Methylene Blue(MB) dye degradation under visible light irradiation was due to its wider absorption edge and higher separation rate of photo-generated electron and holes. In the experimental conditions, it is demonstrated that the MB was effectively degraded by more than 95% within 40 min when the Co–Ag3VO4 catalyst was calcined at 300°C with 1 wt.% Co content.

Sign in / Sign up

Export Citation Format

Share Document